PIR46 360° PIR Motion Sensor
Product Information
Specifications
- Function: PIR46
- Voltage: 220 – 240V AC
- Power: Not specified
- Frequency: 50/60 Hz
- Ambient Light: Not specified
- Time Delay: Not specified
- Rated Load: Not specified
- Detection Area: Not specified
- Detection Distance: Not specified
- Detection Motion Speed: Not specified
- Installation Type: Indoor
Product Usage Instructions
- Installation:
- Setting Up:
- Operation:
- Maintenance:
1. Ensure the power supply is disconnected before
installation.
2. Mount the PIR46 device securely in the desired indoor
location.
3. Connect the device to a 220-240V AC power source.
1. Adjust the detection area and distance settings based on your
requirements.
2. Set the time delay for the light activation after motion
detection.
1. Once installed and set up, the PIR46 will detect motion
within the specified area.
2. When motion is detected, the device will activate the
connected load (e.g., lights).
1. Regularly check and clean the device to ensure proper
functioning.
Frequently Asked Questions (FAQ)
1. How can I adjust the detection area of the PIR46?
To adjust the detection area, refer to the user manual for
specific instructions on changing the settings.
2. Can the PIR46 be used outdoors?
No, the PIR46 is designed for indoor installation only.
INSTRUCTION MANUAL
PIR46
360° PIR Motion Sensor
Indoor Installation
1. INTRODUCTION The PIR46 automa cally turns on lights or any electrical device within the sensors rated load, when mo on and body heat is detected. It has a 360° detec on range and an installa on height of up to 4m, with adjustable se ngs for Lux and Time. Specially designed for long passages or large rooms with a detec on range of 30m in length and a width detec on range of 10m, easily integrated into new or exis ng setups. With an IP20 ra ng, the sensor is intended for inside installa ons. Installa on must be done by a qualified professional.
2. SPECIFICATIONS
Function Voltage Power Frequency Ambient Light Time Delay Rated Load Detection Area Detection Distance Detection Motion Speed Installation Type
Range 220 – 240V AC 50/60 Hz <3 – 2000 Lux 10 sec (±3 sec) to 15 min (±2 min) 2000W Incandescent/ 1000W LED/CFL 360° 10m x 30m Max <24°C 0.6 to 1.5m/s Ceiling Surface Mount
Function Working Temperature Working Humidity Power Consumption Installation Height IP Protection Swivel Head Warranty Standards
Range -20~40°C. <93% RH Approx. 0.5W 2.2 – 4m IP20 Indoor Installation No 5 years IEC 60669-1, IEC 60669-2-1 AS/NZS 60669.1, AS/NZS 60669.2.1
3. FUNCTION a. Sensor Can identify between day and night (Lux Mode):
The consumer can adjust working state in different ambient light. It can work in the day time and at night when it is adjusted on the ” ” (sun) position (max). It can work in the ambient light less than 3 LUX when it is adjusted on the “3” position (min). As for the adjustment pattern, please refer to the testing pattern. b. Time-Delay is added continually: When the sensor detects movement while the light is already on, the countdown timer resets. This means the light will remain On for the full set duration from the moment of the latest detection. c. Adjustable Time Delay: The sensor can be set according to the consumer’s desire (10s, 30s, 90s, 3min, 7min, 15min)
4. CONTROL SETTING INFORMATION ! Turn the TIME knob anticlockwise to the minimum (10s). Turn the LUX
knob clockwise to the maximum (Sun). ! Switch on the power; the sensor will require 30 seconds to warm up.
Once the sensor detects movement, the lamp will turn On. If no other movement is detected within the time duration set, the light will turn Off within the 10 seconds ±3 sec. ! Turn the LUX knob anticlockwise to the minimum (3). If the ambient light is more than 3 Lux, the sensor is not able to function. If the ambient light is less than 3 Lux (dark), the sensor will operate.
Note: When testing in daylight, please turn Lux knob to position, otherwise the sensor will not work!
(Sun)
5. INSTALLATION & WIRING OPTIONS
! Unscrew and remove fixing bracket from base of the sensor. ! Insert the power cable into the slot provided. ! Connect the power cable into the terminal block as per the wiring
diagram. ! Identify the ideal field of view and use fixing bracket mounting
holes to ensure correct alignment for motion sensor. ! Drill holes and screw the fixing bracket to the marked location. ! Reconnect the sensor to the fixing bracket and fasten the screws. ! Once installation is complete, swivel the head to point in the
intended direction, secure it, and turn on the power to test.
6. WIRING INFORMATION 7. SENSOR INFORMATION
WARNING: Danger of Death Through Electrical Shock Y Must be installed by professional
electrician. Y Disconnect power source. Y Cover or shied any adjacent live
components.
8. INSTALLATION ADVICE ! Avoid pointing the detector towards objects with highly
reflective surfaces, such as mirrors etc. ! Avoid mounting the detector near heat sources, such as
heating vents, air conditioning units, light etc. ! Avoid pointing the detector towards objects that may move in
the wind, such as curtains, tall plants etc.
Note: The PIR sensor operates by detecting motion when the detector beams are interrupted, typically by the movement of an object or a walking person. If a person walks directly in front of or towards the beam, the sensor may not detect movement. However, when two beams are crossed, the PIR sensor detects movement, as it picks up the change in the infrared radiation pattern caused by the interruption of both beams. This method increases detection accuracy and reduces the chances of false or non-detection.
9. TROUBLESHOOTING
MAJOR TECH (PTY) LTD
South Africa
Australia
www.major-tech.com
www.majortech.com.au
sales@major-tech.com
info@majortech.com.au
Documents / Resources
 |
MAJOR TECH PIR46 360° PIR Motion Sensor [pdf] Instruction Manual PIR46 360 PIR Motion Sensor, PIR46, 360 PIR Motion Sensor, PIR Motion Sensor, Motion Sensor, Sensor |