UHF-100 Series Wireless Microphone System
Product Information
Technical Specifications
- Transmission frequencies: 660-690MHz
- Frequency band: UHF
- Number of channels: 99
- Bandwidth: 30MHz
- Signal to noise ratio: > 90dB
- Total harmonic distortion: < 0.3%
Product Usage Instructions
1. Powering On/Off
To power on the UHF-100&200 system, press the ON/OFF button
located on the device. To power off, press the same button
again.
2. Adjusting Settings
Utilize the Adjustment button to navigate through different
settings on the screen. Use the Volume button to adjust the audio
output levels.
3. Connecting Antennas and Outputs
Connect Antenna A and Antenna B to ensure proper signal
reception. Use Balanced Output A and Balanced Output B for audio
output connections.
4. IR Pairing and Frequency Transmission
Press the IR pairing button to transmit frequency information to
the transmitter. Ensure proper IR transmission for seamless
operation.
5. Battery Installation and Monitoring
To install or replace batteries, open the Battery compartment
cover and insert batteries into the Battery compartment. Monitor
battery status using the indicator.
FAQ
Q: What frequency band does the UHF system operate in?
A: The UHF system operates in the 660 MHz to 690 MHz frequency
band.
Q: How many channels are available in the UHF-100&200
series?
A: There are 99 channels available in the UHF-100&200 series
for versatile use.
Q: What European Directive does the UHF-100&200 series
comply with?
A: The UHF-100&200 series wireless microphone systems comply
with the European Directive 2014/53/EU.
UHF-100&200
SE T
SE T SE T
USER MANUAL
SET
1/ ON/OFF button 2/ IR transmitter 3/ Screen 4/ Adjustment button 5/ IR transmission of the frequency to the transmitter 6/ Audio signal indicator 7/ UHF signal indicator 8/ Volume button 9/ Antenna A 10/ Antenna B 11/ Mixed output 6.35mm jack 12/ Balanced output A 13/ Balanced output B 14/ Power supply connector
1 /Grid 2 / Control screen 3 / ON/OFF switch 4 / IR pairing button 5 / Battery compartment 6 / Battery compartment cover
UHF channel used
GROU P
MUTE indicator
Frequency used
Battery status indicator
INTRODUCTION
Thank you for choosing Mac Mah and its UHF-100&200 series wireless microphone system. This user’s manual covers the following systems: UHF-100 (M): Single channel diversity handheld mic version. UHF-200 (M) : Two channel handheld microphone version. Before using your equipment, we recommend that you read all the instructions in this manual. instructions in this manual. Mises en garde 1 / Read all instructions in this manual carefully. 2 / There are no user replaceable parts. 3 / Do not expose the unit to heat, rain or any source of moisture. source of moisture. 4 / Handle the microphone with care, do not drop it. 5 / Modification of the device will void the warranty.
FREQUENCES & CONFORMITY
UHF systems operate in the 660 MHz to 690 MHz frequency band. MacMah declares that the UHF-100&200 series wireless microphone systems comply with the European Directive 2014/53/EU.
UHF-100&200 System Operation – Handheld mic Version 1/ Unpack all the components of the system. We recommend that you keep your packaging. 2/ Connect the AC adapter to the power connector on the back of the receiver and receiver and then to the power outlet. 3/ Connect the audio cord to the OUTPUT jack on the back of the receiver. Note: The UHF-200R dual receiver has 3 audio outputs: 1 balanced XLR output for each channel and 1 6.35mm jack output for the «mixed» output (channel 1 + channel 2). 4/ Unfold the antennas. 6 / Press the power switch on the receiver, the power indicator will light up. 5/ Select the frequency you want to use with the SET button. 6/ On the handheld microphone, open the battery compartment. Insert the battery in the direction shown. 7/ Turn on the handheld microphone, if the battery indicator light is flashing, your battery is low. 8/Press the IR button on the handheld microphone and then the IR button on the receiver. Move your microphone closer to the receiver screen to pair. 9 / Adjust the receiver volume.
TECHNICAL SPECIFICATIONS
Transmission frequencies: 660-690MHz
General Frequency band : ………………………………………………………………. UHF Number of channels: …………………………………………………………. 99 Bandwidth ………………………………………………………………………….30MHz Signal to noise ratio : …………………………………………………………. > 90dB Total harmonic distortion : …………………………………………………… < 0,3%
Receiver Power supply : ………………………………………………………………….. DC 12V/500mA Consumption : ………………………………………………………………….. < 3W Audio signal level of XLR outputs (balanced) : ………………………. 400 mV Audio signal level of the mixed jack output (unbalanced) : ……… 200 mV Signal to noise ratio : …………………………………………………………. > 96dB De-Emphasis : ………………………………………………………………….. 50 µs
Handheld mic Power supply : ………………………………………………………………….. 2x 1.5V AA Emission power : ………………………………………………………………. 30mW Max. Type of modulation : ………………………………………………………….. FM Max. deviation : ………………………………………………………………… +/- 25 kHz Average autonomy : ………………………………………………………….. 6 heures Average distance : …………………………………………………………….. 50m Max. 80m Micro capsule type : …………………………………………………………… Unidirectional dyna-
mic microphone
Documents / Resources
 |
MAC MAH UHF-100 Series Wireless Microphone System [pdf] User Manual UHF-100 M, UHF-200 M, UHF-100 Series Wireless Microphone System, Wireless Microphone System, Microphone System |