LUTRON PD-OSENS-WH, PD-VSENS Caseta Wireless Motion Sensor User Guide

Q: Can I use rechargeable batteries with the motion sensor?
A: No, only use high-quality lithium batteries, size CR123, 3V. Rechargeable batteries may damage the sensor.

Q: What should I do with used batteries from the device?
A: Dispose of batteries in compliance with legal requirements. Contact your waste disposal provider for information on proper battery disposal.
Q: How do I contact customer support for assistance?
A: You can reach Lutron customer support at the following numbers:
- U.S.A / Canada: 1.844.LUTRON1
- Others: +1.610.282.3800

Wireless
Quick Start Guide

Motion Sensor

Please Read Before Installing
Welcome—and thank you for purchasing a Caséta motion sensor. The sensor provides hands-free operation by automatically turning on and turning off the lights simply by entering and exiting the room.

Extend Your Warranty

Love Caséta motion sensors? Have ideas for making them better? Tell us what you think and we’ll extend your warranty by 1 year. www.casetawireless.com/register

Contents supplied

Tools you’ll need

Important notes

The sensor is intended for indoor use only. Operate between 32 °F and 104 °F (0 °C and 40 °C).
Use only high-quality lithium batteries, size CR123, 3 V (ANSI-5018LC, IEC-CR17345). DO NOT use rechargeable batteries. Using improperly rated batteries could damage the sensor.
NOTICE: DO NOT disassemble, crush, puncture, drop on a hard surface, subject to high heat, place in water, paint, incinerate, or alter batteries in any way. Please dispose of batteries in compliance with all applicable legal requirements. Your waste disposal provider may have information regarding any state or local restrictions on battery disposal.

The battery in this device contains Perchlorate material, special handling may apply. For more information visit www.dtsc.ca.gov/hazardouswaste/perchlorate

WARNING: Entrapment hazard. To avoid the risk of entrapment, serious injury, or death, these controls must not be used to control equipment which is not visible from every control location or which could create hazardous situations such as entrapment if operated accidentally. Examples of such equipment which must not be operated by these controls include (but are not limited to) motorized gates, garage doors, industrial doors, microwave ovens, heating pads, etc. It is the installer’s responsibility to ensure that the equipment being controlled is visible from every control location and that only suitable equipment is connected to these controls. Failure to do so could result in serious injury or death.

Customer Assistance
www.lutron.com/support
U.S.A / Canada: 1.844.LUTRON1
Others: +1.610.282.3800

Limited Warranty

For warranty information, please see www.lutron.com/warranty

FCC / IC Information

For FCC /IC information: Please visit: www.lutron.com/fcc-ic

Lutron, Caséta, the Lutron Caséta & RA2 Select app logo, and Smart Bridge are trademarks or registered trademarks of Lutron Electronics Co., Inc. in the US and / or other countries.
App Store is a trademark of Apple Inc., registered in the U.S. and other countries.
All other product names, logos, and brands are property of their respective owners.
© 2018-2020 Lutron Electronics Co., Inc.

Insert Battery

Insert battery as shown.

Motion Sensor Setup Using a Smartphone or Tablet (Bridge required, sold separately)
If you are using the load control (dimmers / switches / fan controls) and sensor with the Lutron Smart Bridge follow the instructions below.

Download and launch the Lutron app

Search for “Lutron Caséta” www.casetawireless.com/lutronapp

Click the settings icon and choose Add Device. Use the Lutron app to complete all the remaining steps.

Motion Sensor Pairing without Using a Smartphone or Tablet (Bridge not required)

Pairing the sensor to a Caséta load control device (dimmer / switches / fan control).

Press and hold “OFF” button on the load control

Press and hold button on the sensor

Sensor Placement and Coverage

Before mounting the sensor, please note the following:

If you cannot see the sensor, it cannot see you. The sensor cannot see through glass.

The sensor should be mounted at eye level. Recommended placement 6 to 8 ft (1.8 to 2.4 m).
DO NOT place the sensor within 4 ft (1.2 m) of moving air currents (ie: HVAC vents), heat sources (ie: light bulbs, or microwave / standard ovens), or within 6 in (15 cm) of other RF devices.
If there is line of sight from the sensor to the paired devices (no obstructions) sensor can be located within 60 ft (18.3 m). Otherwise sensor must be within 30 ft (9.1 m).

Whenever possible, avoid placing the sensor in a location where it has a broad view outside the intended space.

For additional tips and recommendations for sensor placement and coverage visit: www.casetawireless.com/sensorcoverage

Sensor Coverage

Minor Motion Coverage- (small movement, i.e., turning a page) 15 X 2 X 35 = 1050 ft2 (97.5 m2)

Major Motion Coverage- (large movement, i.e., walking) 20 X 2 X 45 = 1800 ft2 (167.2 m2)

Temporary Mounting

To test sensor coverage, a 3MT CommandT adhesive strip is provided for temporarily mounting the sensor. The strip is not reusable and should not be used for permanently mounting the sensor.

Testing Sensor Coverage

Press and release the “Test” button on the top of the sensor. The lens will glow briefly, indicating the test mode has been entered.
With the sensor temporarily mounted in the intended location, walk around the space while observing the lens. If the lens glows, motion is detected. If you are not satisfied with the sensor’s performance, relocate the sensor and repeat the test.

Press and release the “Test” button again to exit test mode.

Testing Wireless Communication

Press and release the button to toggle the lights on and off, while the sensor is in its intended mounting location.
If the lights do not respond properly, refer to the Troubleshooting section.

Removing Temporary Mounting Strip
Pull down very slowly. DO NOT pull at an angle.

Permanent Mounting
The sensor is designed to be free-standing or for installation on drywall or plaster surfaces.

Flat Wall-Mount
The flat wall-mount bracket is designed to mount flat against a wall. Use the provided screws and drywall anchors.

Mark wall
Drill holes
Push anchors into wall and mount bracket

Corner-Mount
The corner-mount bracket can be used to mount in a corner or angled on a wall away from a corner.

Mounting directly in a corner
Use the mounting bracket side “A” and the provided screws.
Mounting angled on wall away from corner
Use the mounting bracket side “B”. Use provided screws and drywall anchors.

Advanced Sensor Features

The sensor has three adjustable advanced set-up modes. For most installations, the default settings will provide the best performance. If you determine the default settings require adjustment, refer to the back of the sensor. For additional information, visit www.casetawireless.com/sensorfeatures

Timeout: The sensor will turn off if no motion occurs for the duration of the timeout period. The available timeout settings are: 1, 5, 15, and 30 minutes. (Default: 15 minutes)

Activity: The sensitivity of the sensor can be adjusted based on the expected level of activity within the room. There are three available activity settings: Low Activity, Medium Activity, and High Activity. (Default: Low Activity)
Auto-On: (PD-OSENS model only) When Enabled, lights will turn on automatically when the room is entered and turn off when vacant. When Disabled, lights will need to be manually turned on but will turn off automatically when the room becomes vacant. (Default: Enabled)

Recommendation: For applications in bedrooms or when pets are in the space, it’s suggested to change Auto-on setting to Disabled.

Troubleshooting

Symptom	Solution
Lights do not turn ON when pressing the button.	Verify that the load control device is installed properly AND turned ON at the breaker.
	Verify that the sensor was successfully paired with the correct load control.
	Ensure that the sensor is within range. 30 ft (9.1 m) with obstructions, 60 ft (18.3 m) without.
	Make sure that the battery has been installed correctly (Refer to Step 1).
	Check if the light bulb is blown out.
Lights do not turn ON when space is occupied.	While in the final mounted position, ensure that the wireless communication is working properly by pressing the button on the sensor.
	If the lights were turned off manually, verify that the room has been unoccupied for the duration of the sensor timeout period. (Press the button on the sensor, if lights come on, this was the issue and sensor is operating correctly).
	Change the activity setting of the sensor to Medium or Low Activity. Refer to the back of the sensor or visit www.casetawireless.com/sensorfeatures
	Ensure that the intended motion is occurring within the coverage area (Refer to Step 3).
	(Occupancy Versions Only) Verify that the Auto-On setting of the sensor is set to “Enabled”. Refer to the back of the sensor or visit www.casetawireless.com/sensorfeatures
Lights turn OFF while space is occupied.	Change the timeout setting to a longer timeout. Refer to the back of the sensor or visit www.casetawireless.com/sensorfeatures
	Check that the view of the sensor is not obstructed (Refer to Step 3).
	Change the activity setting of the sensor to Medium or Low Activity. Refer to the back of the sensor or visit www.casetawireless.com/sensorfeatures
Lights stay ON after space is vacated.	Verify that the room has been unoccupied for the duration of the sensor’s timeout period.
	Check that the sensor is not mounted within 4 ft (1.2 m) of moving air currents (i.e.: HVAC vents), heat sources (i.e.: light bulbs, or microwave / standard ovens), or within 6 in (15 cm) of other RF devices.
	Change the activity setting of the sensor to Medium or High Activity. Refer to the back of the sensor or visit www.casetawireless.com/sensorfeatures
	Pet movement may be detected by the sensor and signal that the space is occupied.
	Make sure that the battery has been installed correctly (Refer to Step 1).
Lights won’t turn ON automatically after I manually turn them OFF.	The room must be vacant for the duration of the sensor’s timeout period. After this time, if the room becomes occupied, the sensor will turn ON the lights.
Behavior of lights does not match sensor settings.	Check sensor settings. Refer to the back of the sensor or visit www.casetawireless.com/sensorfeatures
Behavior of lights does not match sensor settings.	Check that all of the sensors paired to the same load control device are using the same settings. Refer to the back of the sensor or visit www.casetawireless.com/sensorfeatures
Sensor lens does not glow in response to motion during sensor coverage testing.	Ensure all items in Step 3 have been followed. For additional details, visit www.casetawireless.com/sensorcoverage
	Make sure that the battery has been installed correctly (Refer to Step 1).
Lens does not stop glowing during sensor coverage testing even when there is no motion.	Check that the sensor is not mounted within 4 ft (1.2 m) of moving air currents (i.e.: HVAC vents), heat sources (i.e.: light bulbs, or microwave / standard ovens), or within 6 in (15 cm) of other RF devices.
Sensor lens flashes and lights do not turn ON when space is occupied.	Verify that the sensor is not in test mode (Refer to Step 5). Visit www.casetawireless/sensorfeatures
	Replace the battery (Refer to Step 1).

For additional help with sensor features visit: www.casetawireless.com/sensorfeatures
For additional tips and recommendations for sensor placement and coverage visit: www.casetawireless.com/sensorcoverage

Documents / Resources

LUTRON PD-OSENS-WH, PD-VSENS Caseta Wireless Motion Sensor [pdf] User Guide
PD-OSENS-WH, PD-VSENS, PD-OSENS-WH PD-VSENS Caseta Wireless Motion Sensor, PD-OSENS-WH PD-VSENS, Caseta Wireless Motion Sensor, Wireless Motion Sensor, Motion Sensor, Sensor

References

User Manual

LUTRON PD-OSENS-WH, PD-VSENS Caseta Wireless Motion Sensor

Product Usage Instructions