CCD-0007739 Key Less RV Door Lock with Bluetooth
“
Product Information
Specifications
- Product Name: SolidStep 4.0
- Operational Weight Rating: 500 lbs (227 kg)
- Maximum Floor Height: 46.75 inches
- Minimum Floor Height: 35.25 inches
- Leg Heights: Short Leg and Long Leg options available
Product Usage Instructions
Pre-Installation
Before installation, measure the door frame inner flange as
depicted in Fig. 2 to ensure proper fit.
Installation
To secure the SolidStep 4.0 Threshold Hinge Plate:
- Remove the threshold hinge plate from the SolidStep 4.0 by
pulling both spring-loaded hinge pins out far enough so that the
plate separates from the step.
Securing and Storing the Steps
After installation, make sure to securely store the steps
following manufacturer’s recommendations to prevent accidents and
damage.
Operation
Follow these steps for operating the SolidStep 4.0:
- Release Steps: Properly release the steps for use.
- Leg Extension Adjustment: Adjust the leg extensions as needed
for stability. - Securing and Storing the Steps: Secure and store the steps when
not in use.
FAQ
Q: What should I do if I encounter difficulties during
installation?
A: If you face challenges during installation, refer to the
provided resources or contact a qualified professional for
assistance.
Q: Is it necessary to wear any safety equipment while using the
product?
A: It is recommended to wear eye protection during service,
maintenance, or installation procedures. Additional safety
equipment like hearing protection, gloves, and face shields may be
required based on the task being performed.
“`
SolidStep® 4.0
OEM INSTALLATION MANUAL
TABLE OF CONTENTS
Introduction
2
Safety
2
Resources Required
3
SolidStep® 4.0 Floor Height Variations
3
Installation
4
Securing the SolidStep 4.0 Threshold Hinge Plate
4
Pre-Installation
4
Final Adjustment of Transport Lock
7
Operation
9
Release Steps
9
Leg Extension Adjustment
10
Securing and Storing the Steps
10
Notes
11
Introduction
The SolidStep® 4.0 is a trailer entry step assembly that can be mounted to the side of any trailer, providing an ease of entry, regardless of level ground.
For information on the assembly or individual components of this product, please visit: https://support.lci1.com/steps-support-solidstep.
NOTE: Images used in this document are for reference only when assembling, installing and/or operating this product. Actual appearance of provided and/or purchased parts and assemblies may differ.
Safety
Read and understand all instructions before installing or operating this product. Adhere to all safety labels.
This manual provides general instructions. Many variables can change the circumstances of the instructions, i.e., the degree of difficulty, operation and ability of the individual performing the instructions. This manual cannot begin to plot out instructions for every possibility, but provides the general instructions, as necessary, for effectively interfacing with the device, product or system. Failure to correctly follow the provided instructions may result in death, serious personal injury, severe product and/or property damage, including voiding of the Lippert limited warranty.
The “WARNING” symbol above is a sign that a procedure has a safety risk involved and may cause death or serious personal injury if not performed safely and within the parameters set forth in this manual.
Failure to follow instructions provided in this manual may result in death, serious personal injury and/or severe product and property damage, including voiding of the component warranty.
Unit MUST be supported per manufacturer’s recommendations before working underneath. Failure to do so may result in death or serious personal injury.
Rev: 01.17.25
Page 2
CCD-0007739
The “CAUTION” symbol above is a sign that a safety risk is involved and may cause personal injury and/or product or property damage if not safely adhered to and within the parameters set forth
in this manual
No repairs should be attempted by anyone other than a qualified professional. The deployment and retraction of the step assembly can cause injury if proper precautions are not taken. The step assembly was designed for an operational weight rating of 500 lbs (227 kg).
Always wear eye protection when performing service, maintenance or installation procedures. Other safety equipment to consider would be hearing protection, gloves and possibly a full face
shield, depending on the nature of the task.
Moving parts can pinch, crush or cut. Keep clear and use caution.
Resources Required
· Cordless or electric drill or screw gun · Appropriate drive bit · 7/16″ wrench or socket · Measuring tape
· #10 x 1 1/2″ wood screws (wood floor) · #10 x 1 1/2″ self-tapping screws (laminate floor) · Non -permanent method of marking
SolidStep® 4.0 Floor Height Variations
Figure 1 depicts an example from the chart below (a quad step, specifically) of the typical variations for the SolidStep 4.0 step assembly. Make sure the correct SolidStep 4.0 variation is installed for the intended unit by also measuring the door frame threshold. Step identification tags are located under one of the step extrusions, typically the top full step.
Fig. 1
35.25″ Minimum
46.75″ Maximum
SolidStep 4.0 Assembly Steps Double Step 8″ Rise Double Step 8″ Rise Triple Step 8″ Rise Quad Step 8″ Rise
Rev: 01.17.25
Maximum to Minimum Floor Height 27.75″ Maximum to 22.25″ Minimum Floor Height 30.75″ Maximum to 26.25″ Minimum Floor Height 39.75″ Maximum to 27.25″ Minimum Floor Height 46.75″ Maximum to 35.25″ Minimum Floor Height
Page 3
Leg Height Short Leg Long Leg Long Leg Long Leg
CCD-0007739
Pre-Installation
If the measurement of the door frame inner flange (Fig. 2) to opposite door frame inner flange is an even number, i.e. 28, 30, 30 1/2, etc., center the threshold hinge plate (Fig. 3A) for installation. If the measurement of the door frame inner flange to opposite door frame inner flange (Fig. 2) is an odd number, i.e. 27, 29, 29 1/4″, etc., the threshold hinge plate (Fig. 3A) will be shifted 1″ to the left from the center of the threshold for installation. Record the measurement of the door frame inner flange to door frame inner flange for later use in installation. The latches (Fig. 10A) on the step assembly will be preset and will additionally account for any offset of the threshold hinge plate if the inner flange to inner flange measurement is an odd number. Fine tune adjustments to the latches can be made once the threshold plate is installed and the steps are attached.
Fig. 2
Door Frame Inner Flange
Measure
Door Frame Inner Flange
Installation
Securing the SolidStep 4.0 Threshold Hinge Plate
1. Remove the threshold hinge plate (Fig. 3A and 4A) from the SolidStep 4.0 by pulling both spring loaded hinge pins (Fig. 3B and 4B) out far enough so that the threshold hinge plate separates from the SolidStep 4.0.
Fig. 3
B
A
B
Fig. 4 A B
Rev: 01.17.25
Page 4
CCD-0007739
2. Look for the notch (Fig. 5B) at the center edge of the threshold hinge plate (Fig. 5A), this notch will be aligned to the center of the door frame threshold or 1″ left of center, depending on the door frame inner flange measurement. Figure 6 shows the door frame inner flange for verification. Place the threshold hinge plate notched side (Fig. 5B), flush against the door frame threshold (Fig. 5D). Screw holes (Fig. 5C) in the threshold hinge plate will be farthest away from the door frame threshold. Fig. 5
A
C
D B
3. Use the measurement of the inner flange to inner flange and find the center (Fig. 6A). Align the threshold hinge plate notch to the center of the door frame threshold or if the door frame is an odd measurement, to the left 1″ from the center (Fig. 6B) of the door frame inner flange measurement.
Fig. 6
C
C
C
C
C D
B
A
4. Install #10 x 1 1/2″ wood screws for a wood floor or #10 x 1 1/2″ self-tapping screws (Fig. 6C) for a laminate floor in the five predrilled screw holes (Fig. 6D).
Rev: 01.17.25
Page 5
CCD-0007739
5. Place the SolidStep 4.0 assembly (Fig. 7B) into the door frame (Fig. 7A), in the extended position. 6. Pull the spring loaded hinge pins (Fig. 8A) out and move the Solidstep 4.0 assembly towards the threshold
hinge plate aligning the center hinge barrel (Fig. 8B) with the threshold hinge plate barrels (Fig. 8C).
Fig. 7
Fig. 8
B
A
C A B
C
A
7. Release the spring loaded threshold pins (Fig. 9A) so that the Solidstep 4.0 assembly is now attached to the threshold hinge plate.
Fig. 9
A
A
Rev: 01.17.25
Page 6
CCD-0007739
Final Adjustment of Transport Lock
Prior to using the transport lock, the latching mechanism may need to be adjusted to the proper left-right orientation and tightened in position. Attempting to engage the transport lock without
proper adjustment may cause damage to the door frame or step assembly. 1. Lift up SolidStep 4.0 to its stored position (Fig. 10). Make sure transport latch flanges (Figs. 10A, 11A
and 12A) are resting against the door frame. If final adjustment is required, loosen the two bolts (Fig. 11B and Fig. 12B) on either side of the adjustable transport lock. This allows for side-to-side adjustment in the latch mechanism.
Fig. 10
A
A
Fig. 11 A
Rev: 01.17.25
Fig. 12 A
B B
B B
Page 7
CCD-0007739
Do not overtighten the bolts. Overtightening the bolts may damage the threads or cause the bolt heads to break off.
2. Once the transport lock mechanism (Fig. 13A) and the transport latch flanges (Figs. 14A and 15A) are in the correct position, tighten the bolts (Figs. 14B and 15B) with a 7/16″ wrench or socket.
3. Once the transport lock has been adjusted, test its functionality by shaking the step assembly to simulate road vibration.
4. Engage and disengage the transport lock (Fig. 14C) to ensure the transport latch flanges (Figs. 14A and 15A) do not scrape against the door frame (Figs. 14D and 15C).
Fig. 13
Fig. 14 A
A D
Transport lock view from inside.
Fig. 15
B C
B
A
C B
B
Rev: 01.17.25
Page 8
CCD-0007739
Operation
Moving parts can pinch, crush or cut. Keep clear and use caution.
Release Steps
1. From the stowed position (Fig. 16), disengage the transport lock (Fig. 16A) by pulling the transport lock knob to the right.
2. Firmly grasp and pull out the vertically-stored SolidStep 4.0 and rest the step firmly on the ground. 3. Adjust leg extensions as needed. See Leg Extension Adjustment section.
Fig. 16
A B
Rev: 01.17.25
Page 9
CCD-0007739
Leg Extension Adjustment
The leg extension is secured with a spring-loaded catch pawl (Fig. 17A). Adjustments can be made to the leg extensions in 1″ increments by extending or retracting the inner leg for the optimal angle and to adjust for the ground surface angle. 1. Pull the spring-loaded catch pawl (Fig. 17A) up to release it from the tube and the slot
in the angle. 2. Extend or retract the inner leg (Fig. 18A) as needed so the steps are parallel to the ground and level
when extended, and unobtrusive while retracted. 3. When the leg is at the desired position, release the spring-loaded catch pawl into the tube and slot
closest to where the inner leg and tube meet to lock them (Fig. 19).
Fig. 17
Fig. 18
A
A Fig. 19
Securing and Storing the Steps
1. Retract leg extensions. See Leg Extension Adjustment section. 2. Lift up SolidStep 4.0 to its stored position (Fig. 16) until the transport locks engage and click into place. 3. Make sure the latches (Fig. 16B) are resting against the door frame. 4. Once the transport locks have been engaged, test the locking functionality by shaking the step
assembly to simulate road vibration, making sure that the SolidStep 4.0 is secure.
Rev: 01.17.25
Page 10
CCD-0007739
Notes
Rev: 01.17.25
Page 11
CCD-0007739
The contents of this manual are proprietary and copyright protected by Lippert. Lippert prohibits the copying or dissemination of portions of this manual unless prior written consent from an authorized Lippert representative has been provided. Any unauthorized use shall void any applicable warranty. The information contained in this
manual is subject to change without notice and at the sole discretion of Lippert. Revised editions are available for free download from lippert.com.
Please recycle all obsolete materials.
For all concerns or questions, please contact Lippert Ph: 432-LIPPERT (432-547-7378) | Web: lippert.com | Email: customerservice@lci1.com
Documents / Resources
 |
LiPPERT CCD-0007739 Key Less RV Door Lock with Bluetooth [pdf] Instruction Manual CCD-0007739 Key Less RV Door Lock with Bluetooth, CCD-0007739, Key Less RV Door Lock with Bluetooth, RV Door Lock with Bluetooth, Lock with Bluetooth, with Bluetooth |