CCD-0002707 Onecontrol Bluetooth Switch
Product Information
Specifications
- Product Name: Bluetooth Switch
- Model Number: CCD-0002707
- Battery Requirement: Two (2) CR 2032 batteries
- Manufacturer: Lippert
- Website: https://support.lci1.com/onecontrol-wireless-formerly-myrv
Product Usage Instructions
Safety Precautions
Read and understand all instructions before installing or
operating the Bluetooth switch. Adhere to all safety labels.
Installation Steps
- Remove the red tab on the back of the switch to activate the
battery. - Using a flat head screwdriver, remove the switch cover from the
mounting plate. - Position the mounting plate on the wall at the desired
location. - Check the mounting plate for level using a bullet level.
- Mark the location of the four mounting holes on the wall.
- Attach the mounting plate to the wall using four #2 wood screws
with an electric or cordless drill. - Reattach the switch cover.
Frequently Asked Questions (FAQ)
Q: What type of batteries does the Bluetooth switch
require?
A: The Bluetooth switch requires two (2) CR 2032 batteries.
Q: Where can I find additional support for this product?
A: For additional support, please visit: https://support.lci1.com/onecontrol-wireless-formerly-myrv
OneControl® Bluetooth Switch
OEM INSTALLATION MANUAL
TABLE OF CONTENTS
Introduction
2
Safety
2
Resources Required
2
Installation
3
Introduction
This document explains how to install the wireless switches which pair to the OneControl® controller. The controller MUST be equipped with bluetooth capability that allows the controller to operate different functionalities. The bluetooth switches are OPTIONAL equipment. OneControl® Bluetooth Switches come in 2, 4, 5 and 6 button configurations with various preassigned functions.
For additional support on this product, please visit: https://support.lci1.com/onecontrol-wireless-formerly-myrv.
NOTE: Images used in this document are for reference only when assembling, installing and/or operating this product. Actual appearance of provided and/or purchased parts and assemblies may differ.
Safety
Read and understand all instructions before installing or operating this product. Adhere to all safety labels.
This manual provides general instructions. Many variables can change the circumstances of the instructions, i.e., the degree of difficulty, operation and ability of the individual performing the instructions. This manual cannot begin to plot out instructions for every possibility, but provides the general instructions, as necessary, for effectively interfacing with the device, product or system. Failure to correctly follow the provided instructions may result in death, serious personal injury, severe product and/or property damage, including voiding of the Lippert limited warranty.
Resources Required
· Cordless or electric screw gun · Assorted drill bits · Phillips head bit or screwdriver
· Flat head screwdriver · Pen or pencil · Bullet level
Rev: 02.18.2025
Page 2
CCD-0002707
Installation
NOTE: Installation location of the bluetooth switches will vary by OEM and the floor plan of a particular unit. NOTE: Remove red tab on the back of the switch in order to activate the battery (Fig. 1). In the event that it
is necessary to replace the batteries, the switch requires two (2) CR 2032 batteries. 1. Using the tip of a flat head screwdriver, remove the switch cover from the mounting plate by inserting
the tip into the side slot of switch and pry open (Fig. 2A).
Fig. 1
Fig. 2
A
2. With the switch cover removed, position the mounting plate in the predetermined location on the wall. 3. Check the mounting plate for level using a bullet level. 4. Using a pen or pencil mark the location of the four mounting holes located in each corner of the
mounting plate (Fig. 3).
Fig. 3
Mounting Hole
Mounting Hole
5. Using an electric or cordless drill, attach the mounting plate onto the wall with four #2 wood screws. Do not over-tighten screws. Over-tightening screws may cause cracking in the mounting plate.
6. Reattach the switch cover.
Rev: 02.18.2025
Page 3
CCD-0002707
The contents of this manual are proprietary and copyright protected by Lippert. Lippert prohibits the copying or dissemination of portions of this manual unless prior written consent from an authorized Lippert representative has been provided. Any unauthorized use shall void any applicable warranty. The information contained in this manual is subject to change without notice and at the sole discretion of Lippert. Revised editions are available
for free download from lippert.com.
Please recycle all obsolete materials.
For all concerns or questions, please contact Lippert Ph: 432-LIPPERT (432-547-7378) | Web: lippert.com | Email: customerservice@lci1.com
Documents / Resources
 |
LiPPERT CCD-0002707 Onecontrol Bluetooth Switch [pdf] Instruction Manual CCD-0002707, CCD-0002707 Onecontrol Bluetooth Switch, Onecontrol Bluetooth Switch, Bluetooth Switch, Switch |