Contents
hide
ledyilighting DSA DMX512-SPI Decoder and RF Controller
Compatible with 34 kinds IC/Numeric display/Stand-alone function/Wireless remote control
Features
- DMX512 to SPI decoder and RF controller with digital display.
- Compatible with 34 kinds digital IC RGB or RGBW LED strip, IC type and R/G/B order can be set.
- Compatible ICs: TM1803, TM1804, TM1809, TM1812, UCS1903, UCS1909, UCS1912, UCS2903, UCS2909, UCS2912, WS2811,WS2812, TM1829, TLS3001, TLS3002 GW6205, MBI6120, TM1814B, SK6812, UCS8904B, LPD6803, LPD1101, D705, UCS6909, UCS6912, LPD8803, LPD8806, WS2801, WS2803, P9813, SK9822, TM1914A, GS8206,GS8208.
- DMX decode mode, standalone mode and RF mode selectable.
- Standard DMX512 compliant interface, set DMX decode start address by buttons.
- Under stand-alone mode, change mode, speed or brightness by bottoms.
- Under RF mode, match with RF 2.4G RGB/RGBW remote control.
- 32 kinds dynamic mode, include horse-race, chase, flow, trail or gradual change style.
Technical Parameters
| Input and Output | |
| Input voltage | 5-24VDC |
| Power consumption | 1W |
| Input signal | DMX512 + RF 2.4GHz |
| Output signal | SPI(TTL) x 3 |
| Dynamic mode | 32 |
|
Control dots |
170 pixels RGB 510 CH Max 900pixels |
Mechanical Structures and Installations
Wiring diagram
Note
- If the SPI LED pixel strip is single-wire control, the DATA and CLK output is same, we can connect up to 6 LED strips.
- If the SPI LED pixel strip is two-wire control, we can connect up to 3 LED strips.
Operation
IC type, RGB order and pixel length length setting
- You must first assure IC type, RGB order and pixel length of the LED strip is correct.
- Long press M and ◀ key, prepare for setup IC type, RGB order, pixel length, automatic blank screen, Short press M key to switch four item.
- Press ◀ or ▶ key to setup value of each item.
- Long press M key for 2s, or timeout 10s, quit setting.
IC typ
RGB orde
Pixel length
Disable automatic blank screen
IC type table
| No. | IC type | Output signal |
| C11 | TM1803 | DATA |
| C12 | TM1809,TM1804,TM1812,UCS1903,UCS1909,UCS1912, UCS2903,UCS2909,UCS2912,WS2811,WS2812 | DATA |
| C13 | TM1829 | DATA |
| C14 | TLS3001,TLS3002 | DATA |
| C15 | GW6205 | DATA |
| C16 | MBI6120 | DATA |
| C17 | TM1814B(RGBW) | DATA |
| C18 | SK6812(RGBW) | DATA |
| C19 | UCS8904B(RGBW) | DATA |
| C21 | LPD6803,LPD1101,D705,UCS6909,UCS6912 | DATA,CLK |
| C22 | LPD8803,LPD8806 | DATA,CLK |
| C23 | WS2801,WS2803 | DATA,CLK |
| C24 | P9813 | DATA,CLK |
| C25 | SK9822 | DATA,CLK |
| C31 | TM1914A | DATA |
| C32 | GS8206,GS8208 | DATA |
- RGB order: O-1
- O-6 indicate six order RGB, RBG, GRB, GBR, BRG, BGR.
- Pixel length: Range is 008-900.
- Automatic blank screen: enable (bon) or disable boF automatic blank screen.
DMX decode mode
- Short press M key, when display 001-999, enter DMX decode mode.
- Press ◀ or ▶ key to change DMX decode start address(001-999), long press for fast adjustment.
- Short press M key to switch two item.
- Press ◀ or ▶ key to setup value of each item.
- Decode number display dno: DMX decode channel number, range is 003-600(for RGB).
- Multiple of pixels display Pno : Each 3 DMX channel control length(for RGB), range is 001- pixel length.
- Long press M key for 2s, or timeout 10s, quit setting.
- If there is a DMX signal input, will enter DMX decode mode automatically for example, the DMX-SPI decoder connect with RGB strip.
DMX data from DMX512 console
DMX-SPI decoder output
- Start address: 00
- Decode channel number: 18
- Each 3 channel control length: 1
DMX-SPI decoder output
- Start address: 001
- Decode channel number: 18, each
- 3 channel control length: 3
Stand alone mode
- Short press M key, when display P01-P32, enter stand-alone mode.
- Press ◀ or ▶ key to change dynamic mode number(P01-P32).
- Each mode can adjust speed and brightness.
- Long press M key for 2s, prepare for setup mode speed and brightness.
- Short press M key to switch two item.
- Press ◀ or ▶ key to setup value of each item.
- Mode speed: 1-10 level speed S-1, S-9, S-F.
- Mode brightness: 1-10 level brightness b-1, b-9, b-F.
- Long press M key for 2s, or timeout 10s, quit setting.
- Enter stand-alone mode only when DMX signal is disconnected or lost.
Speed (8 level)
Brightness (10 level,100％)
Dynamic mode list
| No. | Name | No. | Name | No. | Name |
| P01 | Red horse race white ground | P12 | Blue White chase | P23 | Purple float |
| P02 | Green horse race white ground | P13 | Green Cyan chase | P24 | RGBW float |
| P03 | Blue horse race white ground | P14 | RGB chase | P25 | Red Yellow float |
| P04 | Yellow horse race blue ground | P15 | 7 color chase | P26 | Green Cyan float |
| P05 | Cyan horse race blue ground | P16 | Blue meteor | P27 | Blue Purple float |
| P06 | Purple horse race blue ground | P17 | Purple meteor | P28 | Blue White float |
| P07 | 7 color multi horse race | P18 | White meteor | P29 | 6 color float |
| P08 | 7 color horse race close + open | P19 | 7 color meteor | P30 | 6 color smooth sectionally |
| P09 | 7 color multi horse race close + open | P20 | Red float | P31 | 7 color jump sectionally |
| P10 | 7 color scan close + open | P21 | Green float | P32 | 7 color strobe sectionally |
| P11 | 7 color multi-scan close + open | P22 | Blue float |
RF mode
- Match: Long press M and ▶ key for 2s
- Display RLS within 5s, press on/off key of the RGB remote, display RLO, match is successful, then use the RF remote to change mode number, adjust speed or brightness.
- Delete: Long press M and ▶ key for 5s, until display RLE, delete all matched RF remote.
Restore factory default parameter
Long press ◀ and ▶ key, restore factory default parameter, display RES.
Factory default parameter
DMX decode mode, DMX decode start address is 1, decode number is 510, multiple of pixels 1, dynamic mode number is 1, chip type is TM1809, RGB order, pixel length is 170, disable automatic blank screen, without matched RF remote.
Documents / Resources
 |
ledyilighting DSA DMX512-SPI Decoder and RF Controller [pdf] Installation Guide DSA DMX512-SPI Decoder and RF Controller, DSA, DMX512-SPI Decoder and RF Controller |
