Kmart 43471836 Custom Storage Double System Installation Guide

Plaster Wall: When installing on a plaster wall
without studs, use Type A screws and Type B anchors. When
installing on studs, use an electric drill and Type A screws.

Wood Wall: Use a 3mm diameter drill bit and
Type A screws for installation.

Concrete Wall: Use a 6mm diameter drill bit,
Type A screws, and Type C anchors for installation. Secure the
plastic piece in the hole using a hammer.

Step-by-Step Assembly Guide

Step 1: Establish the suitable height and mark
with a pencil. Ensure the hang track is at least 200cm above the
ground if using the full system.

Step 2: Draw a horizontal line based on the
marked points.
Step 3: Use the wall stud finder to locate and
mark the studs.

Step 4: Use a level to ensure the hang track
Beam sticker is horizontal. Secure the hang track according to the
markings ensuring at least one wall strip can be attached to a
stud.
Step 5: Drill holes with Type B anchor
according to the markings on the sticker, then remove the
sticker.

Note: If wall strip cannot be installed on the stud, ensure
at least one Type A screw is used on the hang track with the
stud.

Frequently Asked Questions (FAQ)

Q: Can I install this system on a drywall?

A: Yes, ensure you use appropriate anchors and
screws based on the wall type. For drywall without studs, use Type
A screws and Type B anchors.

Q: Do I need professional help for
installation?

A: While the installation can be done by
following the instructions, if you are unsure or uncomfortable with
any step, seeking professional advice is recommended.

“`

View Fullscreen

Assembly Instructions
43471836 CUSTOM STORAGE DOUBLE SYSTEM
CARE INSTRUCTIONS: WIPE CLEAN WITH A DAMP OR DRY CLOTH. DO NOT USE ABRASIVE MATERIALS AND SOLVENTS. KEEP AWAY FROM WATER AND DIRECT SUNLIGHT.STORE IN A DRY PLACE. FOR INDOOR AND DOMESTIC USE ONLY. WARNING: WHEN THIS PRODUCT IS INSTALLED IN A PLASTER WALL, PLEASE MAKE SURE THAT THE WALL SURFACE IS STABLE, DRY AND INTACT. IF UNSURE PLEASE SEEK PROFESSIONAL ASSISTANCE IN INSTALLING THIS PRODUCT, IN PARTICULAR IF NOT ABLE TO LOCATE A STUD WALL. PLASTER WALLS ARE QUITE DELICATE. BEFORE STARTING TO INSTALL, PLEASE READ THESE INSTRUCTIONS CAREFULLY TO MAKE SURE YOU USE THE RIGHT TOOLS AND FOLLOW THE CORRECT STEPS FOR INSTALLATION. PLEASE CHOOSE THE SUITABLE HARDWARE ACCORDING TO YOUR WALL TYPE. USING A DRILL BIT WITH THE WRONG DIAMETER WILL CAUSE THE HARDWARE INSTALLATION TO FAIL AND DAMAGE THE WALL. A STUD WALL MUST BE LOCATED WITHIN THE SPACE HANGING TO ENSURE MAXIMUM STABILITY AND STRENGTH. THIS PRODUCT REQUIRES AT LEAST TWO PEOPLE FOR INSTALLATION. OPERATING ALONE MAY LEAD TO IMPROPER INSTALLATION OR SAFETY ACCIDENTS. IMPROPER INSTALLATION REQUIRES A SPACE BETWEEN. MAXIMUM SAFE LOAD: 20KG FOR EACH SHELF WITH HANGING RAIL. PLEASE SEEK PROFESSIONAL ADVICE IF IN DOUBT. INSTRUCTIONAL VIDEO: https://youtu.be/Hfe7QugxMdc
Required Assembly Tools

Tape Measure Pencil

Ladder

Hardware List

Phillips Head Screwdriver

Spirit Level Hammer

Electric Drill

Wall Stud Finder

A M4x50mm 32pcs

B M14x40mm 32pcs

C M7.5x38mm32pcs

Only For Plaster Wall

Only For Concrete Wall

Parts List

wire shelf

wall strip

right bracket

left bracket

4PCS 2

6PCS 3

2PCS 4

2PCS

hang track

right hanger hook

left hanger hook

extendable hanger rail

2PCS 6

4PCS 7

2PCS 8

2PCS

connector

3PCS

Beam sticker

1PC

middle bracket

2PCS

INSTRUCTIONAL VIDEO AVAILABLE ONLINE

7 9
4 2
7

1 11
6 2
8
9
1 11
6 2
8

5 1
6

3 2
9

1 6

3 2

Do not tighten the screws fully during assembly. Fully tighten screws after the final assembly steps
Tips Before you Start
APPLICABLE HARDWARE FOR DIFFERENT WALL TYPES AND THEIR METHODS OF USE.

Tape Measure Pencil

Ladder

Spirit Level
Phillips Head Screwdriver

PLASTER WALL: MINIMUM THICKNESS > 10MM WHEN INSTALLING THE PRODUCT ON A PLASTER WALL WITHOUT STUDS, PLEASE USE A SCREWDRIVER WITH TYPE A SCREWS AND TYPE B ANCHORS FOR INSTALLATION. NOTE: WHEN INSTALLING ON STUDS, PLEASE DIRECTLY USE ELECTRIC DRILL AND TYPE A SCREWS.

Phillips Head 3mm Drill Bit

Tape Measure Pencil

Ladder

Spirit Level
Phillips Head Screwdriver

WOOD WALL USE A 3MM DIAMETER DRILL BIT TO MAKE A HOLE AND ENSURE THAT THE DEPTH OF THE INSTALLATION HOLE IS GREATER THAN 5CM. PLEASE USE TYPE A SCREWS FOR INSTALLATION.

Wall Stud Finder
Phillips Head 3mm Drill Bit

Tape Measure Pencil

Ladder

Phillips Head Screwdriver

Spirit Level Hammer

CONCRETE WALL: MASONRY WALLS, CONCRETE WALLS , BRICK WALLS, ETC. USE A 6MM DIAMETER DRILL BIT TO MAKE A HOLE AND ENSURE THAT THE DEPTH OF THE INSTALLATION HOLE IS GREATER THAN 5CM. PLEASE USE TYPE A SCREWS AND TYPE C ANCHORS FOR INSTALLATION. INSTALL TYPE C ANCHOR AND SECURE THE PLASTIC PIECE IN THE HOLE USING A HAMMER.

6mm Drill Bit

This setup shows steps for a plaster wall. If your wall is different, use the right tools shown in the TIPS for your wall type. Please seek professional advice if in doubt.
STEP 1 establish the suitable height and Mark with pencil,
If using the full system, please ensure that the hang track is at least 200cm above the ground.
STEP 2 Draw a horizontal line based on the marked points.
STEP 3 Use the wall stud finder to find the stud and Mark the location of the studs.
wall stud finder wall stud
It is highly recommended that the wall strip is mounted on stud, please try and locate the stud and ensure the screws are used at this point as well as the centre of the hang track.

STEP 4 Use a level to ensure that item hang track Beam sticker is horizontal.
10

Secure the hang track Beam sticker according to the horizontal line with the condition that at least one wall strip can be attached to a stud. Also ensure that the mounting holes of the wall strip align with the location of the stud.
Noted:If wall strlp cannot install on the stud, please make sure at least one type A screw be used on the hang track with the stud.

STEP 5 Drill holes with type B anchor according to the markings on the Sticker, then remove the sticker.
10

note: when install with stud, please use the type A screw . The second hole on the left still use the type a screw, and also this hole is on the stud.

STEP 6

5
BB B

5 5

use the 3rd hold

use the right B

on hang track

Secure one end of the hang track with a screw.

BB BB

Use a level to ensure the hang track is horizontal.

Then secure the remaining screws of the hang track.

warning: if wall strip cannot install on the stud, please make sure at least one type A screw be used on each hang track with the stud.

STEP 7 Hanging the wall strip onto the hang track and positioning into the wall strip install hole per as the beam sticker.

2 Use a spirit level to ensure the wall strip is vertical and mark the installation holes at the same time.
STEP 8 Drill the correct holes according to the marked positions.
B
B
B
note: when install with stud, please use the type A screw .

STEP 9 Secure the wall strip with screws. A

A
2
A

warning: please pay attention to the

type of screws dependant on whether

it is plaster board only or stud wall.

STEP 10 Hanging the wall strip onto the hang track and positioning into the wall strip install hole per as the beam sticker.

2
Use a spirit level to ensure the wall strip is vertical and mark the installation holes at the same time.
Make sure the distance is the same as the top.

Note: please measure the distance before drilling the holes and make sure the distance between the centers of the installation holes is 59cm.

STEP 11 Drill the correct holes according to the marked positions.

B
B
B
note: when install with stud, please use the type A screw .
STEP 12 Secure the wall strip with screws. A
A
2
A
A

warning: please pay attention to the type of screws dependant on whether it is plaster board only or stud wall.

STEP 13 Hanging the wall strip onto the hang track and positioning into the wall strip install hole per as the beam sticker.

Note: please measure the distance before drilling the holes and make sure the distance between the centers of the installation holes is 59cm.
STEP 14 Drill the correct holes according to the marked positions.

Use a spirit level to ensure the wall strip is vertical and mark the installation holes at the same time.
Make sure the distance is the same as the top.

B
B
B
note: when install with stud, please use the type A screw .

STEP 15 Secure the wall strip with screws.

A
A
2
A

warning: please pay attention to the type of screws dependant on whether it is plaster board only or stud wall.
STEP 16 Use a connector to attach the lower part of
the wall strip.

A
STEP 17 Remove the lower wall strip and drill holes
at the marked locations, according to your wall type.

9
B

2
Use a spirit level to ensure the wall strip is vertical and mark the installation holes at the same time.

B B B
note: when install with stud, please use the type A screw .

STEP 18 Secure the wall strip with screws.

STEP 19 Use a connector to attach the lower part of
the wall strip.

A
A
2
A
A
warning: please pay attention to the type of screws dependant on whether it is plaster board only or stud wall.
STEP 20 Remove the lower wall strip and drill holes
at the marked locations, according to your wall type.

2
Use a spirit level to ensure the wall strip is vertical and mark the installation holes at the same time.

Make sure the distance is the same as the top.

Note: please measure the distance before drilling the holes and make sure the distance between the centers of the installation holes is 59cm.

STEP 21 Secure the wall strip with screws.

B
note: when install with stud, please use the type A screw .

A
warning: please pay attention to the type of screws dependant on whether it is plaster board only or stud wall.

STEP 22 Use a connector to attach the lower part of
the wall strip.

STEP 23 Remove the lower wall strip and drill holes
at the marked locations, according to your wall type.

9
B

Note: please measure the distance before drilling the holes and make sure the distance between the centers of the installation holes is 59cm.

Use a spirit level to ensure the wall strip is vertical and mark the installation holes 2 at the same time.
Make sure the distance is the same as the top.

STEP 24 Secure the wall strip with screws.

B B B
note: when install with stud, please use the type A screw .

warning: please pay attention to the type of screws dependant on whether it is plaster board only or stud wall.

A
A
2
A
A

STEP 25 install the left, middle and right brackets and apply a downward push to ensure it is locked in place.
4 11 3
4 11 3

STEP 26 Install the wire shelf and ensure that the snaps underneath the wire shelf engage with the notches. Secure the
wire shelf and give it a push to ensure it is locked in place.When the wire shelf is locked, the front end is flush.
1 1
1 1

STEP 27 hanger Installation: attach the hanger hook on the opening of the bracket, then install the hanger rail on the hook.
Please ensure that hanger rail is securely installed and tightly fastened. Please seek professional advice if in doubt.

7 8 6

8 6

7 8 6

8 6

Documents / Resources

Kmart 43471836 Custom Storage Double System [pdf] Installation Guide
43471836, 43471836 Custom Storage Double System, 43471836, Custom Storage Double System, Double System, System

References

User Manual

Kmart 43471836 Custom Storage Double System Installation Guide

43471836 Custom Storage Double System

Product Specifications

Product Usage Instructions

Required Assembly Tools

Parts List

Assembly Instructions

Tips Before you Start

Step-by-Step Assembly Guide

Frequently Asked Questions (FAQ)

Documents / Resources

References

Leave a comment

Cancel reply