JRN-340K IT Controller
Product Information
Specifications:
- Model: JRN-430K
- Communication: 4G/3G/GSM
- Supported Frequency Bands:
- GSM/GPRS/EDGE: Quad band 850/900/1800/1900MHz
- UMTS/HSPA+: Eight band 850/900/1700/1900/2100MHz
- LTETwelve band: 700/800/850/900/1800/1900/2100/2600MHz
- Output Power: Class E2 for GSM, Class 3 for
UMTS
Configuration:
- Equipment: IT Controller, Communication
Module, Battery pack, eSIM - Models: JRN-340K, Cinterion PLS63-WTelit,
NBB-3400TOCAD ENERGY, 7DZLE0001docomo
Product Usage Instructions
Installation:
- Connect the mechatronic I/F cable to the vehicle
batteries. - Insert a fuse with a recommended current rating of 2A for
protection against overcurrent. - Ensure proper power supply and control unit connection.
- Install LTE, GPS antennas for communication.
Operation:
- The device operates during key OFF status, performing periodic
batches at specified times. - It responds to server calls and acquires current location
information via GPS for generating out-of-area alerts.
Frequently Asked Questions (FAQ)
Q: How do I charge the built-in battery pack?
A: The built-in battery pack must be charged by replenishing
power when external power is supplied. Continuous power
replenishment is necessary to maintain battery capacity.
IT Controller (used 4G/3G/GSM Communication) JRN-430K
1/21 LE245523
IT Controller (used 4G/ 3G/ GSM Communication)
JRN-340K
User Manual
Doc# : LE-246534 Ver.1.00
Date: Jun. 26, 2024
@Copyright JRC Mobility Inc. Locator Products Groupe Product Development Department
IT Controller (used 4G/3G/GSM Communication) JRN-430K
NO
Date
.
1 Jun.26,2024
Number 1.00
The contents of change first edition
2/21 LE245523
–
IT Controller (used 4G/3G/GSM Communication) JRN-430K CONTENTS.
3/21 LE245523
Introduction ……………………………………………………………… 4 Overview …………………………………………………………………. 4 Configuration …………………………………………………………….. 5 Functions ………………………………………………………………… 5 Specifications ……………………………………………………………. 8 External Interface Specifications ………………………………………….. 14 Dimensions ………………………………………………………………. 16 Handling Precautions ……………………………………………………… 18 Compliance Notation ………………………………………………………. 21
IT Controller (used 4G/3G/GSM Communication) JRN-430K
4/21 LE245523
Introduction
The IT controller for 4G communication is a location information communication terminal device with packet data communication function of 4G/3G/GSM system (see table below) and GPS rec eiving function (L1 1.5GHz band). It uses TCP/IP/PPP as the communication protocol.
Overview
Supported frequency bands
Items
Specification
Band
GSM/GPRS/EDGE: Quad band 850/900/1800/1900MHz
UMTS/HSPA+: Eight band 850(BdXIX) / 850(BdVI) / 850(BdV) / 900
(BdVIII) / 1700(BdIII) / 1900(BdII) / 2100(BdIV) / 2100MHz (BdI) LTETwelve band700 (Bd12,Bd28) 800 (Bd20) 850 (Bd18,Bd19,Bd5)
/ 900 (Bd8) / 1800 (Bd3) / 1900 (Bd2) / 2100(Bd1,Bd4) / 2600 (Bd7)
Output Power
(according to release 99)
Class 4 (+33dBm ±2dB) for GSM850
Class 4 (+33dBm ±2dB) for GSM900
Class 1 (+30dBm ±2dB) for GSM1800
Class 1 (+30dBm ±2dB) for GSM1900
Class E2 (+27dBm ± 3dB) for GSM 850 8-PSK
Class E2 (+27dBm ± 3dB) for GSM 900 8-PSK
Class E2 (+26dBm +3 /-4dB) for GSM 1800 8-PSK
Class E2 (+26dBm +3 /-4dB) for GSM 1900 8-PSK
(according to release 99) Class 3 (+24dBm +1/-3dB) for UMTS 850, WCDMA FDD BdXIX Class 3 (+24dBm +1/-3dB) for UMTS 850, WCDMA FDD BdVI Class 3 (+24dBm +1/-3dB) for UMTS 850, WCDMA FDD BdV Class 3 (+24dBm +1/-3dB) for UMTS 900, WCDMA FDD BdVIII Class 3 (+24dBm +1/-3dB) for UMTS 1700, WCDMA FDD BdIII Class 3 (+24dBm +1/-3dB) for UMTS 1900, WCDMA FDD BdII Class 3 (+24dBm +1/-3dB) for UMTS 2100, WCDMA FDD BdIV Class 3 (+24dBm +1/-3dB) for UMTS 2100, WCDMA FDD BdI
(according to release 8) Class 3 (+23dBm ±2dB) for LTE 700, LTE FDD Bd12 Class 3 (+23dBm +2dB/-2.5dB) for LTE 700, LTE FDD Bd28 Class 3 (+23dBm ±2dB) for LTE 800, LTE FDD Bd20 Class 3 (+23dBm ±2dB) for LTE 850, LTE FDD Bd18 Class 3 (+23dBm ±2dB) for LTE 850, LTE FDD Bd19 Class 3 (+23dBm ±2dB) for LTE 850, LTE FDD Bd5 Class 3 (+23dBm ±2dB) for LTE 900, LTE FDD Bd8 Class 3 (+23dBm ±2dB) for LTE 1800, LTE FDD Bd3 Class 3 (+23dBm ±2dB) for LTE 1900, LTE FDD Bd2 Class 3 (+23dBm ±2dB) for LTE 2100, LTE FDD Bd4 Class 3 (+23dBm ±2dB) for LTE 2100, LTE FDD Bd1 Class 3 (+23dBm ±2dB) for LTE 2600, LTE FDD Bd7
IT Controller (used 4G/3G/GSM Communication) JRN-430K
Configuration
5/21 LE245523
NO.
Equipment
Model
Quantity
1 IT Controller 2 Communication Module 3 Battery pack
4 eSIM
JRN-340K
1
Cinterion PLS63-WTelit(Note
1
1)
NBB-3400TOCAD ENERGY
1
(Note 2)(Note 3)
7DZLE0001docomo
1
(Note 1) The scope of our quality assurance for the communication module is limited to the isolation of whether problem s caused by the communication module or not. The quality assurance of the communication module is to be p erformed by Telit. Therefore, we will ask Telit to conduct a detailed analysis of the cause of the problem and t o confirm the spread of the defective lot. (Note 2) The built-in battery pack is warranted for 1 year for function and 3 months for performance. Please replace the
battery pack on a regular basis. If periodic replacement is difficult, the performance of the battery itself may deteriorate or the battery may malf unction, which may cause the emergency call function not to operate when the heavy equipment battery is rem oved. In addition, do not use metal products (tools, etc.) when removing and installing the battery connector. The battery may short-circuit, resulting in excessive current flow, which may cause the battery to overheat, rupt ure, leak, or damage the equipment. (Note 3)
The built-in battery pack must be restored to a fully charged state by replenishing (charging) power to the built
-in battery pack when external power is supplied. If no power replenishment continues, the remaining capacity
of the built-in battery pack may decrease or become empty.
It controller (JRN-340K)
Mechatronic I/F cable
To Vehicle batteries(Note3 To Mechatronic Controller
fuse Note2
Built-in battery pack
Communication Module
Power supply and control unit
eSIM
LTE antenna LTE antenna GPS antenna
Configuration Diagram
Note1 Note2
Note3
Please prepare mechatronic I/F cables by customer. A fuse (recommended current rating: 2[A]) is required for the mechatronic I/F cable to pr otect against overcurrent. Fuses should be inserted at two locations: battery and GND. Do not take main power from a DC cigar. Poor contact may cause malfunction.
Functions
(1) Operation during key OFF performs the following. Periodic batches are performed at the specified time. The server responds to the call from the server side. Acquire current location information by GPS and generate out-of-area alerts.
IT Controller (used 4G/3G/GSM Communication) JRN-430K
6/21 LE245523
(2) Standby (power saving) control function Return from standby (power saving) is as follows *Set to allow return by the following interrupt when shifting to standby. CAN1_EN/CAN2_EN (Engine Key) ON from mechatronics Detect ACC ONOFF change Interrupt by RING0 signal from communication module Date and time notification return by date and time setting UART (serial data) receiving from PC Charge signal (HOUR_METER) ON When the device is restored from standby, the application is notified of the restoration. Shift to standby follows the instruction from the application.
(3) Storing operating data Enables storage of operating data.
(4) Clock Enables the current time to be determined by information from GPS satellites. Maintains and counts the date and time even when the main power is disconnected.
(5) Backup It retains the IT controller’s operation mode and communication settings even when the ma in power is disconnected. Also, when fully charged, within one hour (typ), at least one set of mail can be sent and received to and from the server.
(6) External communication function It has 3 channels: mechatronics (CAN2), mechatronics 2 (CAN1), and monitor (RS-232C). The communication protocol for CAN1/2 is SAE J1939, and baud rates of 250k/500k are s upported.
(7) GPS Both during key ON and key OFF, coordinates are acquired every 30 minutes or so. Rollover is described separately.
(8) 4G/3G/GSM communications Built-in communication module enables data communication using 4G/3G/GSM communicati on. The mobile communication network will be compatible with NTTdocomo line.
(9) Software rewriting It also enables software rewriting using WiFi and monitor (RS-232C) port.
(10) LED indication The following LED indications are provided. Power source In/out of range of cellular phone netwok
(11) Mechatronics commands [supported by user application] The following command exchanges information with the mechatronics via CAN communicati on. Key ON Engine ON Key OFF
IT Controller (used 4G/3G/GSM Communication) JRN-430K
Alarm Fuel level Engine water level Engine oil level Fluid level Engine oil pressure Engine water temperature Air cleaner Charge DS (forced key OFF) RT (status inquiry) HS (hour meter change) CTO (command) Automatic key OFF judgment processing HD (Health Diagnostic command)HD FD (Failure Diagnosis command)FD
7/21 LE245523
(12) Communication protocols in cell phone networks Send in e-mail format to a mail server using the TCP/IP protocol.
(13) Operates at UTC+h. h can be rewritten from outside. (Server input and console input)
(14) WLAN WLAN that enables communication at 2.4GHz using IEEE802.11g/n is supported in AP mo de. WLAN Alliance certification (device certification) is not obtained.
(15) Abnormality detection function
It has a function to detect the following abnormalities and notify the VCU. Built-in battery pack removal CAN1/2 communication line disconnection
IT Controller (used 4G/3G/GSM Communication) JRN-430K
Specifications
.1 Mechatronic interface specifications
(1) Mechatronic CAN2 (standard)
NO.
Item
Specification
1
Data transmission method SAE J1939
2
Data transmission speed 250k/500kbps
Depends on software configuration
3
Communication format
Extension 29bit
(2) Mechatronic CAN1Second
NO.
Item
Specification
1
Data transmission method SAE J1939
2
Data transmission speed 250k/500kbps
Depends on software configuration
3
Communication format
Extension 29bit
8/21 LE245523
(3) Monitor port (maintenance connector)
NO.
Item
Specification
1
Data transmission method Half-duplex start-stop synchronization
2
Signal level
RS-232C
3
Data transmission speed 115,200bps
4
Frame length
Variable length
5
Data length
8bit
6
Start bit
1bit
7
Parity bit
None
8
Stop bit
1bit
9
Character code
EUC
IT Controller (used 4G/3G/GSM Communication) JRN-430K
.2 General Specifications
NO.
Item
Specification
9/21 LE245523
1 Supply voltage Voltage range DC +10 to +16V (max. 32V)
2 Built-in battery Secondary battery Nickel-metal hydride battery (Ni-MH)
Pack
NBB-3400500mAh/4.8V
3 SIM interface 1.8V/3.0V
4 Current consu During communication: Average current 400mA or less/12V (+25°C)
mption
During standby: 23mAtyp./12V (when not charged, +25°C, within range)
(Target value) (Note 1)
5 Surrounding e Operating temperature: -30 to +70°C
nvironment
Storage temperature: -40 to +85°C
Operating humidity: 0 to 95%Rh (non-condensing)
Communication module operation is subject to communication module s
pecifications.
6 Dimensions 7 Weght
Also, when using the built-in battery pack Operating temperature: -20°C to +70°C Charging temperature: 0°C to +70°C 200 x 60 x 30 (mm) (Excluding protrusions) Less than 400g
8 Cabinet
Material : PBT 751SA
(Note 1) The condition for intermittent receiving operation within the range is LTE communication DRX= 256.
After the LTE communication module is set to sleep when the power-saving mode is shifted, the LTE module starts intermittent receiving operation.
The receiving interval of intermittent receiving varies according to the DRX (Discontinuous r eceiving) value specified by the communication operator as follows. (DRX is specified from 32
to 256)
Receive interval: 10 ms * DRX value.
Every 0.32 seconds for DRX=32 Every 0.64 seconds for DRX=64 Every 1.28 seconds for DRX=128 Every 2.56 seconds for DRX=256
(*) When out of range, the standby current increases due to carrier search.
IT Controller (used 4G/3G/GSM Communication) JRN-430K .3 Communication module (GPS function) specifications
10/21 LE245523
No Item
Specifications
1 Receiving satellite
GPS, QZSS
2 Incoming signal
GPS : 1575.42MHz (L1) QZSS : 1575.42MHz (L1C)
3
Number of receiving channe ls
55ch
4 Positioning accuracy
< 2m CEP-50 (Open Sky)
*The rollover of the GNSS receiver will temporarily revert t
o the past date (April 28, 2013) on December 12, 2032,
but will then automatically recalibrate to the correct presen
t date in a few minutes.
5 Geodetic system
WGS-84 (default)
6 Time system
UTC
7 Antenna detection function None
IT Controller (used 4G/3G/GSM Communication) JRN-430K .4 Communication module (communication function) specifications
11/21 LE245523
No.
Item
1 Type name
2 Radio frequency *1
3 Transmitting output (room temperature) *2
Specifications Cinterion PLS63-W (Thales) GSM/GPRS/EDGE: Quad band 850/900/1800/1900MHz UMTS/HSPA+: Eight band850(BdXIX) / 850(BdVI) / 850(BdV)
/ 900(BdVIII) / 1700(BdIII) / 1900(BdII) / 2100(BdIV) / 2100MHz (BdI)
LTETwelve band700 (Bd12,Bd28) 800 (Bd20) 850 (Bd18,Bd 19,Bd5) / 900 (Bd8) / 1800 (Bd3) / 1900 (Bd2) / 2100(Bd1,Bd 4) / 2600 (Bd7)
(according to release 99) Class 4 (+33dBm ±2dB) for GSM850 Class 4 (+33dBm ±2dB) for GSM900 Class 1 (+30dBm ±2dB) for GSM1800 Class 1 (+30dBm ±2dB) for GSM1900 Class E2 (+27dBm ± 3dB) for GSM 850 8-PSK Class E2 (+27dBm ± 3dB) for GSM 900 8-PSK Class E2 (+26dBm +3 /-4dB) for GSM 1800 8-PSK Class E2 (+26dBm +3 /-4dB) for GSM 1900 8-PSK
(according to release 99) Class 3 (+24dBm +1/-3dB) for UMTS 850, WCDMA FDD BdXI X Class 3 (+24dBm +1/-3dB) for UMTS 850, WCDMA FDD BdVI Class 3 (+24dBm +1/-3dB) for UMTS 850, WCDMA FDD BdV Class 3 (+24dBm +1/-3dB) for UMTS 900, WCDMA FDD BdVII I Class 3 (+24dBm +1/-3dB) for UMTS 1700, WCDMA FDD BdIII Class 3 (+24dBm +1/-3dB) for UMTS 1900, WCDMA FDD BdII Class 3 (+24dBm +1/-3dB) for UMTS 2100, WCDMA FDD BdI V Class 3 (+24dBm +1/-3dB) for UMTS 2100, WCDMA FDD BdI
(according to release 8) Class 3 (+23dBm ±2dB) for LTE 700, LTE FDD Bd12 Class 3 (+23dBm +2dB/-2.5dB) for LTE 700, LTE FDD Bd28 Class 3 (+23dBm ±2dB) for LTE 800, LTE FDD Bd20 Class 3 (+23dBm ±2dB) for LTE 850, LTE FDD Bd18 Class 3 (+23dBm ±2dB) for LTE 850, LTE FDD Bd19 Class 3 (+23dBm ±2dB) for LTE 850, LTE FDD Bd5 Class 3 (+23dBm ±2dB) for LTE 900, LTE FDD Bd8 Class 3 (+23dBm ±2dB) for LTE 1800, LTE FDD Bd3 Class 3 (+23dBm ±2dB) for LTE 1900, LTE FDD Bd2 Class 3 (+23dBm ±2dB) for LTE 2100, LTE FDD Bd4 Class 3 (+23dBm ±2dB) for LTE 2100, LTE FDD Bd1 Class 3 (+23dBm ±2dB) for LTE 2600, LTE FDD Bd7
IT Controller (used 4G/3G/GSM Communication) JRN-430K
12/21 LE245523
4 Receiving sensitivity -97dBm or less
(room temperature)*3
5 LTE specification
3GPP Release 10 UE CAT 1 supported
DL 10Mbps, UL 5Mbps
6 HSPA specification 3GPP Release 7
DL 7.2Mbps, UL 5.7Mbps
HSDPA Cat.8 / HSUPA Cat.6 data rates
Compressed mode (CM) supported according to 3GPP TS2
5.212
7 UMTS specification 3GPP Release 4
PS data rate 384 kbps DL / 384 kbps UL
CS data rate 64 kbps DL / 64 kbps UL
8 SMS specification
Point-to-point MT and MO
Cell broadcast
Text and PDU mode
Storage: SIM card plus SMS locations in mobile equipment
*1 The following bands supported by PLS63-W are masked by this device as unused ba nds. LTE: Bd13
*2,*3 These are the guaranteed design values of the communication module alone and do not guarantee the performance of the module when installed on construction equip ment. Communication status should be checked in the actual usage environment.
Fig. : PLS63-W Block Diagram
IT Controller (used 4G/3G/GSM Communication) JRN-430K
.5 Built-in battery pack specifications
NO
Item
Specifications
1 Type name
NBB-3400
2 Type
Nickel-Metal Hydride battery (Ni-MH)
3 Nominal Voltage
4.8V
4 Nominal capacity
500mAh
5 Battery Label
See diagram below.
13/21 LE245523
Fig. : Internal Battery Pack Label Diagram
.6 External Connector Specifications
N
Item
O
Specofications
1 Interface connector
ManufacturerTE
Type name : 368050-1
IT Controller (used 4G/3G/GSM Communication) JRN-430K
External Interface Specifications
.7 Interface Connector Specifications .7.1 Pin assignment table
1
BAT
Battery
2
GND
GND
3
HOUR_MET Hour meter signal (operating/non-operating
ER
discrimination signal)
4
GND
GND
5
NC
NC
6
NC
NC
7
MONI_RXD IT Controller Monitor
8
MONI_TXD Monitor IT Controller
9
CAN0_EN CAN0 Enable
10
CAN0_H
CAN0 High-Level input-output
11
CAN0_L
CAN0 Low-Level input-output
12
GND
GND
13
CAN1_EN CAN1 Enable
14
CAN1_H
CAN1 High-Level input-output
15
CAN1_L
CAN1 Low-Level input-output
16
GND
GND
14/21 LE245523
Connector Outline Drawing Mating surface
IT Controller (used 4G/3G/GSM Communication) JRN-430K .8 Power Serial Interface Equivalent Circuit
15/21 LE245523
1
BAT
DC/DC Converter
to PWR SPLY
3
HOUR_METER
To CPU
7
MONI_RXD
8
MONI_TXD
9/13
CAN0/1_EN
10/14
CAN0/1_H
from Serial Interface IC from Serial Interface IC Enable control circuit from CAN Interface IC
11/15
CAN0/1_L
from CAN Interface IC
5/6
NC
2/4/12/16
GND
Fig: Power Serial Interface Equivalent Circuit
IT Controller (used 4G/3G/GSM Communication) JRN-430K
Dimensions
.9 JRN-340K
16/21 LE245523
Fig : Outline drawing of JRN340K
IT Controller (used 4G/3G/GSM Communication) JRN-430K
17/21 LE245523
About GPS Week Number Rollover The GNSS receiver rollover will temporarily revert to the past date (April 28, 2013) on December 12, 2032, but will then automatically recalibrate to the correct present date within a few minutes.
IT Controller (used 4G/3G/GSM Communication) JRN-430K
18/21 LE245523
Handling Precautions
Caution
Instruction
This symbol indicates a general caution, warning, or hazard not otherwise specified.
This symbol indicates a general action to the user.
Procedure for turning off the power Prohibition
This symbol indicates that the user must unplug the power plug from the outlet.
This symbol indicates a general prohibition notice.
Disassembly Pr This symbol indicates a prohibition against disassembling this de
ohibited
vice, which may cause electric shock or other problems.
Don’t touch No wetting
This symbol indicates a prohibition notice for touching certain par ts of the product under certain conditions that may result in injur y. This symbol indicates a prohibition notice when the product is us ed in a place where water may be splashed, wet, soaked, applie d, or spilled, which may cause electric shock or fire due to elect rical leakage.
.10 Specification values Be sure to observe the specification values for this device. Exceeding the specificati
on values may cause malfunctions. 1 Power supply voltage: Main unit (input voltage) This is the maximum voltage that can be applied between the power supply terminal and the ground terminal (GND). 2 Operating Temperature The operating temperature is the temperature range within which the product can operate satisfying the specifications. Exceeding this temperature range may result in malfunction. 3 Storage Temperature This is the temperature range for storing the product without operating it, and if the temperature exceeds this range, the performance may not be satisfied. Exceeding this temperature range may result in malfunction.
.11 Precautions for use 1 This product is not suitable for use in areas where children are likely to be present. 2 Do not unscrew or disassemble this equipment. Doing so may cause performance degradation or malfunction.
3 When performing maintenance with the screws removed, be sure to take me asures against static electricity (battery replacement, reset switch operation, et c.). Failure to do so may cause performance degradation or malfunction.
4 Dropping this device or leaving it outside for a long period of time may cause scratches, stains, or malfunctions.
5 This equipment is not designed for use in the following special environments. Do not use the instrument in the following special environments, as it may cause
IT Controller (used 4G/3G/GSM Communication) JRN-430K
19/21 LE245523
performance degradation or malfunction.
-Water, oil, chemicals, organic fluids, etc.
-In dust -In corrosive gases such as salt air, chlorine, hydrogen sulfide, ammonia, sulfur oxides, hydrogen chloride, and sulfurous gases. -Environment with strong static electricity or electromagnetic waves
6 Do not use for medical equipment, space, aerospace equipment, disaster prevention, security equipment, or other equivalent equipment that requires a high level of safety that may affect human life.
7 Do not use the product near people wearing medical or electrical equipment. Radio waves may cause malfunction of medical equipment, etc.
8 Depending on the car model, the antenna may affect in-vehicle electronic devices. When installing or wiring the antenna, it should be installed and wired as far away from in-vehicle electronic devices as possible. In particular, when installing a GPS antenna, please install it as far away from the car navigation system and other antennas as possible. This may cause performance degradation.
9 Forcing, heating, pulling, or bending the cable with heavy objects may damag e the cable and cause fire or electric shock.
11 Do not operate it while driving a car or machine. Doing so may cause an ac cident.
12 If water, metal, or other foreign objects enter the interior, first turn off the po wer to the product, disconnect the power cable, and contact us. Using the pr oduct as it is may cause fire, electric shock, or malfunction.
13 When cleaning, turn off the power and unplug the power cable for safety. Fai lure to do so may cause fire or electric shock.
14 When cleaning the surface, do not use organic solvents such as thinner or b enzene. They may damage the surface paint. To clean the surface, remove d ust and dirt and wipe with a clean cloth
.12 Precautions for implementation 1 When handling this equipment, be careful to avoid static electricity. Static electricity may cause malfunctions. In particular, pay attention to static electricity on the interface connector. 2 Be sure to turn off the power circuit before inserting connectors. Also, avoid collision and insert the connectors in parallel.
3 Be careful not to touch the terminals of the interface connector with bare or greasy hands.
4 Do not use or leave the equipment in high direct sunlight or in high temperat ures. Doing so may cause overheating, deformation, or malfunction of the eq uipment.
5 Install the main unit and cables in such a way that they do not interfere with the operation or handling of airbags or other equipment.
6 Connect each cable securely to the product. Failure to do so may cause the cables to disconnect or damage the connectors.
7 Do not install the device near devices that generate magnetic fields, such as high-voltage power lines or transformers. The device may not operate properl y.
IT Controller (used 4G/3G/GSM Communication) JRN-430K
20/21 LE245523
.13 Overcurrent protection
1 This device does not have a built-in fuse for overcurrent protection. To prevent hazards, use a fuse for overcurrent protection in the power supply line.
.14 Storage Precautions 1 Avoid locations where corrosive gases such as salt air, chlorine, hydrogen su lfide, ammonia, sulfur oxides, hydrogen chloride, and sulfurous gases are gen erated. 2 Since condensation will form on a set of equipment in places where there ar e sudden changes in temperature and humidity, avoid such environments and store the equipment in places where there are few changes in temperature. 3 Do not place the product on an unstable surface, such as on a wobbly table or on a tilted surface. Doing so may cause the product to fall, resulting in malfunction or injury. 4 Do not store the product in a humid or dusty place. Doing so may cause ov erheating, ignition, or malfunction.
.15 Transportation Method 1 Do not throw or drop it. Doing so may break the device.
2 Do not allow it to get wet. Please be careful not to get it wet during transpo rtation during rainfall and snowfall.
.16 Disposal 2 Do not throw batteries into fire. It may explode and cause fire or injury.
.17 Other 1 Please note that we are not responsible for any defects or abnormalities cau sed by deviations from the specifications.
2 The Company reserves the right to change to alternative components to the extent that electrical, mechanical, and environmental characteristics are not im paired with respect to the equipment described in this specification.
3 If the enclosure becomes too hot to touch, avoid touching it directly, stop usi ng it immediately, and contact our sales department or the nearest branch or sales office.
4 Never perform internal inspections or repairs by the customer. Inspection and repair by unprofessional maintenance personnel may result in fire or electric shock. For internal inspection and repair, contact our sales department or the nearest branch/branch office or distributor.
IT Controller (used 4G/3G/GSM Communication) JRN-430K
Compliance Notation
21/21 LE245523
True Importer No subject countries
Compliance with FCC/IC Rules and Regulations (USA and Canada)
FCC This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm betwe en the radiator and any part of your body. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. IC This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Scien ce and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux C NR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est aut orisée aux deux conditions suivantes : 1. L’appareil ne doit pas produire de brouillage; 2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susce ptible d’en compromettre le fonctionnement.
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolle d environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body.
Documents / Resources
 |
JRC Mobility JRN-340K IT Controller [pdf] User Manual JRN-340K, JRN-430K, JRN-340K IT Controller, JRN-340K, IT Controller, Controller |