V2+R12
Dual Color LED Controller Kit
Contents
hide
V2PlusR12 Dual Color LED Controller Kit
- Ultra sensitive color temperature touch slide.
- Smooth dimming and switch without any ickering.
- Light on/off fade time 3s selectable.
- Magnet on the back which can be easily stuck on back holder or any metal surfaces.
Technical Parameters
| LED Receiver’s Input and Output | LED Remote’s Input and Output | ||
| nput voltage | 10.5A | Output signal | RF2.4GHz |
| Input current | 12-24VDC | Working voltage | 3VDC(CR2032) |
| Output voltage | 2x(12-24)VDC | Working current | ＜5mA |
| Output current | 2CH,5A/CH | Standby current | ＜10μA |
| Output power | 2x(60-120)W | Standby time | 1.year |
| Output type | Constant voltage | Remote distance | 30m(Barrier-free space) |
| Dimming data | Warranty and Protection | ||
| Dimming level | 0 -100% | ||
| Dimming range | Logarithmic | Warranty | 5 years |
| Dimming curve | 4096 (2^12) levels | Protection | Reverse polarity Short circuit |
| PWM Frequency | 2000Hz (default) | ||
| Safety and EMC | |
| Radio Equipment | EN 55015 EN IEC 61547:2023 ETSI EN 301 489-1 ETSI EN 301 489-3 ETSI EN 301 489-17 EN 55032EN 55035 |
| EMC standard | EN 61347-2-11 EN 61347-1 |
| Safety standard | EN 62479:2010 EN 50663:2017 ETSI EN 300 440 ETSI EN 300 328 |
| Certication | CE RED |
| Environment | |
| Operation temperature | Ta: -30 OC ~ +55 OC |
| Case temperature (Max.) | Tc: +85 OC |
| IP rating | IP20 |
Mechanical Structures and Installations
To fix the remote, three options are offered for selection:
Option 1. Can be adsorbed directly onto metal surfaces.
Option 2. Fix the remote’ back holder on the wall with two screws.
Option 3. Adhere the remote’ back holder to the wall with paster.
Note:
- Before the first use, please remove the protective film on the battery.
- If the LED indicator is not on when press key, it is due to dead battery or bad contact caused by multiple plugging, please replace the battery, or raise the battery shrapnel with a screw driver.
Wiring Diagram
Note:
- Long press the match key for 15s to enable the continuous switch off-on two times rapidly to switch 3 levels color temperature function (This feature is disabled by factory default).
Long press the match key for 10s to restore the factory setting. - Power failure memory: after setting the light state for 5s, the current light state will be saved automatically, the light state will not be changed when re-powering.
Key Function
Match Remote Control (two match ways)
End user can choose the suitable match/delete ways. Two options are offered for selection:
| Use the controller’s Match key Match: Short press match key, immediately press on/off key of the remote. Delete: Press and hold match key for 5s to delete all match, The light blinks 5 times means all matched remotes were deleted. |
Use Power Restart Match: Switch off the power, then switch on power, repeat again. Immediately short press on/off key 3 times on the remote. The light blinks 3 times means match is successful. Delete: Switch off the power, then switch on power, repeat again, Immediately short press on/off key 5 times on the remote. The light blinks 5 times means all matched remotes were deleted. |
Dual Color Control
WW=Warm white LED CW=Cool white LED
Each channel can supply up to 120W(@24V) and white balance can be controlled as such:
| Color temperature | Cool white | Neutral white | Warm white |
| Power distribution | WW=0W,CW=120W | WW=60W,CW=60W | WW=120W,CW=0W |
Light on/off Fade Time
Long press match key 5s, then short press match key 3 times, the lighting effect will be set to the fade in and fade out in 3s, the indicator light of LED controller blinks 3 times.
Long press match key 10s, restore factory default parameter, the light on/off time restores to 0.5s.
Malfunctions Analysis & Troubleshooting
| Malfunctions | Causes | Troubleshooting |
| No light | 1. No power 2. Wrong connection or insecure. |
1. Check the power. 2. Check the connection. |
| Uneven intensity between front and rear,with voltage drop | 1. Output cable is too long. 2. Wire diameter is too small. 3. Overload beyond power supply capability. 4. Overload beyond controller capability. |
1. Reduce cable or loop supply. 2. Change wider wire. 3. Replace higher power supply. 4. Add power repeater. |
| No response from the remote | 1. The battery has no power. 2. Beyond controllable distance. 3. The controller did not match the remote. |
1. Replace battery. 2. Reduce remote distance. 3. Re-match the remote. |
User Manual Ver 1.0.5
2024.9
Documents / Resources
 |
iskydance V2PlusR12 Dual Color LED Controller Kit [pdf] Owner's Manual V2PlusR12, V2PlusR12 Dual Color LED Controller Kit, V2PlusR12, Dual Color LED Controller Kit, Color LED Controller Kit, LED Controller Kit, Controller Kit |