SMD V3 4 Channel Traffic Light Controller
“
Specifications:
- 4-Channel Relay
- Control via Wi-Fi with its own Wi-Fi network
- Control via Access Point
- Control multiple devices from a single unit
- Expansion of the number of lights possible by adding another
controller - Cycle count limitation
- Individual manual control for each bulb
- Flash options are available
- Option to control the device using an existing Wi-Fi
network - On/Off control for all lights available with a single button
press - Control AC using SMD Relays
- Factory Reset option and Hard Factory Reset option
- Quiet Relays
- Almost unlimited switching counts
- Reverse option for Motions – Stop, Start, Pause, Resume options
available as Software/Hardware
Product Usage Instructions:
Basic Instructions:
Each motion will have a Start and End Time.
| Motion/Color | Seconds |
|---|---|
| RED | 7-12 |
| YELLOW | 5-7 |
| GREEN | 0-5 |
In this scenario, the green light will be active from 0 to 5
seconds, yellow from 5 to 7 seconds, and red from 7 to 12 seconds
in a continuous cycle.
Changing Light Controller Cycle:
- Power up your board and locate the device’s network in your
device’s Wi-Fi settings (default name starting with LC_********).
Connect to this network. - In any device’s browser, type 192.168.4.1, use the username
‘user’, and change the cycle as needed. - Cycle 0 means unlimited. To control multiple controllers, visit
the Devices page and add the MAC address of the client’s
controller.
FAQ:
Q: Where can I find detailed information on wiring and
setup?
You can check out our YouTube channel at www.youtube.com/@IOTmug
or visit our website at www.iotmug.com. For personalized
assistance, contact us at support@iotmug.com.
Q: How do I perform a factory reset or hard reset?
To perform a factory reset or hard reset, refer to the
instructions provided in the manual or visit the Setup/Settings
page on the device for detailed steps.
“`
4 Channel Traffic Light Controller SMD V3
Features
4-Channel Relay
Control via Wi-Fi. It has its own wifi network
Control via Access Point
Unlimited Traffic Modes Design All achievable with our advanced firmware
Control mul ple devices from a single unit
Expansion of the number of lights is possible by adding another controller to the exis ng system
Cycle count limita on
Individual manual control for each bulb
Flash op ons are available
Op on to control the device using your exis ng Wi-Fi network
On/Off control for all lights available with a single bu on press
Control AC using SMD Relays
So Factory Reset op on. Hard Factory Reset op on
Quite Relays
Almost unlimted switching counts
Reverse op on for Mo ons Stop, Start, Pause, Resume op ons availble as So ware / Hardware
More resource: www.iotmug.com
WIRING – Also See Image 11 below in images gallery
Need help with ASAP: support@iotmug.com
WIRING — Control AC LINES / BULBS Powered By AC Source
Glossary: Mo on: We use mo on to ac vate any relay/device/lamp in a me cycle. You will see M symbol next to each mo on. MAC address: A unique address for each controller. Devices: Controlling mul ple controllers from a single controller. We call Master and Slave / Client Flash: Turn on/off any device frequently within a specified me period. Cycle: You can set a limit for our cycle count. For example, if the cycle is set to 2, it means the controller will stop a er running all mo ons 2 mes. 0 means unlimited cycle count. Custom: Manually control each relay/device. Stop: Stop all mo ons. Start: Begin all mo ons. Turn On/Off ALL: This will turn on all relays. If any client controllers are connected to the master, it will also turn on the clients’ relays. SSID: If you want to connect your device to your WIFI network, you can use this.
Page 1 of 4
More Help Please check out our YouTube channel for detailed informa on: www.youtube.com/@IOTmug. You can also visit us at www.iotmug.com. If you would like a detailed video sent via email, please reach out to us at support@iotmug.com. Please describe what you would like to do, and we will be more than happy to assist you.
Basic Instruc on Each mo on will have Start, End Time.
Motion/M RED YELLOW GREEN
Seconds 7-12 5-7 0-5
For example, in this scenario, the green light will be ac ve from 0 to 5 seconds. Following that, the yellow light will be ac ve from 5 to 7 seconds. Lastly, the red light will be ac ve from 7 to 8 seconds. These light sequences will run in a con nuous cycle. The minimum start me corresponds to the beginning of the cycle, and the maximum end me corresponds to the last point of the cycle.
How to Change Light Controller Cycle 1. Power up your board Image 11 . Locate your device’s network in your device’s Wi-Fi se ngs. It will have a default name
star ng with “LC_********”. Connect to this network (Image 1). Default password is “12345678” 2. In any device’s browser (mobile or computer), type “192.168.4.1” and press Enter. Use the username “user” and
password “123456” (Image 2). 3. You’ll be directed to the default mo on se ngs in your browser (Image 3). These mo ons operate in a cycle/loop. 4. To add a new mo on, click the “Add New Mo on” bu on. Enter your se ngs and click “Add” (Image 4). 5. Modify exis ng mo ons by clicking on them (Image 5). 6. By default, channel Turns on defined mo ons. By Reverse op on, it will be turned off. (Image 12). 7. For manual relay control, click the “Custom” bu on to gain manual access (Image 6). 8. To limit the cycle count, adjust it on the mo on screen and press “Save” (Image 7 shows an example of a 2- me run).
Cycle 0 means unlimited. 9. For controlling mul ple controllers, visit the Devices page. Add the MAC address of the client’s controller and provide a
name (Image 8). You can find the mac address of desired devices on the mo on page (image 3) or “Print Mac Address” page. 10. Customize the device network name, default IP address, and add the device to your Wi-Fi network on the se ngs page. It supports 2.4GHz networks (Image 9).” 11. Factory Reset from Se ngs Page: To perform a factory reset, navigate to the se ngs page, scroll down, and select “Factory Reset.” A erward, turn off the power, then turn it back on. 12. To reset the board to factory se ngs, ensure the device is powered off, then briefly connect the “IO5” pin to GND. Turn the device on and wait for the green light to appear. Once the green light is visible, power off the device again and remove the jumper. Finally, turn the device back on, and it will be restored to its factory se ngs. 13. To enable wired Stop, Start, Pause, and Resume op ons, you need to create connec ons between the ground and the corresponding pin numbers. For example, to use the Stop func on (pin IO4), place a bu on between the Ground pin and the IO4 pin. The other pin assignments are as follows: STOP (IO4), START (IO5), PAUSE (IO2), and RESUME (IO0). If you wish to
IMAGES
Page 2 of 4
Image 1 Controller AP
Image 2 Login Page
Image 3 Mo on Page
Image 4 Add new mo on
Image 5 Update/ Remove Mo on
Image 6 Manual/Custom Relay Control
Page 3 of 4
Image 7 Cycle Count 10 a Factory
Image 8 Adding New Device
Image 9 Setup /Se ngs Page
10 b Stop Wiring (Exmaple)
Image 10a Hard Reset and Image 10b Wired Control Ex: Stop
Image 11 Powering Controller
Page 4 of 4
Image 12 Reverse The Ac on
Documents / Resources
 |
IOTmug SMD V3 4 Channel Traffic Light Controller [pdf] User Guide SMD V3, SMD V3 4 Channel Traffic Light Controller, SMD V3, 4 Channel Traffic Light Controller, Traffic Light Controller, Light Controller, Controller |