ELEVY LASH & BROW TINT AND 3% DEVELOPER
ELEVY LASH & BROW TINT AND 3% DEVELOPER is available in two different shades and will dye the hair for 3-6 weeks, depending on your clients’ natural hair growth.
Tint color options: Black Each tint will come with a 3% cream developer
Lash & Brow Tint and 3% Developer includes
Black Lash & Brow Tint (0.16 fl oz / 5ml) a true natural black that can be used for clients who prefer a subtle or more dramatic black lash
3% Cream Developer (0.16 fl oz / 5ml)
Storage conditions
Store at 41-77°F / 5-25°C.
Do not overcool or overheat.
Avoid direct sunlight.
Keep away from children.
Keep containers closed as the products may lose their properties if exposed to air.
How to apply to brows
When performing and ELEVY Brow Lamination treatment, tinting is done after Step #2 (Volumising Fix) and before Step #3 (Care Plus).
Mix equal parts tint and cream developer into a creamy paste. This mixing ratio is 1:1 (1 cm of tint and 3 drops of cream developer).
Gather the tint on a tint brush and apply it to the brows until they are completely covered. Make sure that the tint is placed in the desired shape and only on the eyebrow hair because it can slightly stain the skin.
Application time varies 5-15 minutes depending on the desired intensity and results (the longer you leave the tint, the darker the results) and apply a thin layer of tint to reduce temporary skin stain.
Remove the tint with a dry cotton pad/ball.
Brush brows into place.
After the treatment
Tell your client to avoid water for 24 hours.
How to apply to lashes
When performing an ELEVY Lash Lift treatment tinting is done after Step #2 (Volumising Fix) and before Step #3 (Care Plus).
Prep: remove any contact lenses, clean the eye area with a lash cleanser and place under eye pads underneath the lashes.
Immediately before tinting, mix equal parts tint and cream developer into a creamy paste. This mixing ratio is 1:1 (1 cm of tint and 3 drops of cream developer).
Apply to lashes using a tint brush.
When performing a lash lift treatment application time varies 8-10 minutes depending on the desired intensity and results (Leave the tint on for 10-15 minutes for darker results).
Remove the tint with a damp q-tip. Make sure the q-tip is not completely saturated with water, it just needs to be slightly damp. Use as many q-tips needed to remove all of the tint from the lashes before applying step 3.
After the treatment
Tell your client to avoid water for 24 hours.
Ingredients
Black Lash & Brow Tint: Aqua, Cetearyl Alcohol, Polyoxyethylene Lauryl ether, Polyquaternium-63, Glycerol, Petrolatum, p-Phenylenediamine, Ethanolamine, Ammonium Hydroxide, Glycerine Monostearate, Ammonium bicarbonate, Decamethylcyclopentasiloxane, Sodium sulfite, EDTA-2Na, 5-Methyl-2-phenyl-1,2dihydropyrazol-3-one, 2-(2,4-Dianminophenoxy) ethanol sulfate, DL-Menthol.
3% Cream Developer: Aqua, Cetearyl Alcohol, Cremophor(R)A25, Glycerine monostearate, Disodium Phosphate, Hydrogen Peroxide, p-Phenylenediamine, Coconut oil, Parfum.
Disclaimer
Your clients skin may stain for 1-3 days.
Documents / Resources
 |
Iolite Lashes ELEVYLash and Brow Tint and 3 Percentage Developer [pdf] Instructions ELEVYLash and Brow Tint and 3 Percentage Developer, Brow Tint and 3 Percentage Developer, Percentage Developer, Developer |
