ICE COBOTICS i18B Automatic Scrubber Instruction Manual

Do not operate the machine in a manner other than
intended.
Ensure the battery compartment is open when charging, except
for maintenance-free batteries.

Avoid sparks and open flames near batteries.

i18C:

This machine is designed for indoor commercial use. Only use
recommended accessories. Follow these safety precautions:

Avoid using flammable materials in tanks or picking them
up.
Replace damaged power cords promptly by authorized personnel
only.

Machine Components:

The machine consists of various components including brush
cover, recovery tank, squeegee, adjusting handle, brush plunger,
and more. Refer to the manual for a detailed list of components for
i18B and i18C models.

Machine Set Up & Installation:

Unpack the machine carefully, checking for any damage.

Report any damage to the carrier immediately.
Ensure the contents of the package include the machine,
squeegee assembly, brush/pad driver, and charger cord.

FAQ

How do I order parts for the ICE Cobotics Automatic
Scrubber?

To order parts, follow these steps:

Identify the machine model and serial number.

Use only ICE Cobotics Company supplied or equivalent
parts.
Order online, by phone, by fax, or by mail.

Provide necessary information like part number, quantity, name,
company name, customer ID, billing and shipping address, phone
number, and purchase order number.

View Fullscreen

www.icecobotics.com

OPERATOR & Parts Manual

i18B i18C

Automatic Scrubber

8019009 REV.07(08-2025)

OPERATOR MANUAL
READ OPERATOR MANUAL MANUAL CAREFULLY
IMPORTANT:7RHQVXUHIXOOZDUUDQWSURWHFWLRQ3OHDVH¿OORXW UHWXUQ your warranty card.
3OHDVH¿OORXWDWWLPHRILQVWDOODWLRQIRUIXWXUHUHIHUHQFH Model No. Serial No. Machine Options Sales Rep. Sales Rep. phone no. Customer ID Number Installation Date
HOW TO ORDER PARTS Only use ICE Cobotics Company supplied or equivalent parts. Parts and supplies may be ordered online,by phone, by fax or by mail. 1. Identify the machine model. 2. Identify the machine serial number from the data label. 3. Ensure the proper serial number is used from the parts list. 4. Identify the part number and quantity.
Do not order by page or reference numbers. 5. Provide your name, company name, customer ID number,billing and shipping address,
phone number and purchase order number.
PROTECT THE ENVIRONMENT Please dispose of packaging materials,old machine components VXFKDVEDWWHULHVKD]DUGRXVÀXLGVLQFOXGLQJDQWLIUHH]HDQGRLO in an environmentally safe way according to local waste disposal regulations.
Always remember to recycle.

ICE Cobotics (GuangDong) Company Limited XiangShi Road LiaoBu DongGuan GuangDong China Tel: 0769 – 81869000 Fax:0769 – 81863000
Specifications and parts are subject to change without notice.
2

i18B/i18C

OPERATOR MANUAL
TABLE OF CONTENTS
SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 MACHINE COMPONENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 MACHINE SETUP & INSTALLATION . . . . . . . . . . . . . . . . . . 7 MACHINE OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . 8 WHILE OPERATING MACHINE . . . . . . . . . . . . . . . . . . . . . . . 8 TANK DRAINING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 PREVENTATIVE MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . 10 BASIC TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 TECHNICAL SPECIFICATION . . . . . . . . . . . . . . . . . . . . . 13 PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 WEAR & TEAR PARTS LIST . . . . . . . . . . . . . . . . . . . 35 WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

i18B/i18C

OPERATOR MANUAL

SAFETY PRECAUTIONS(FOR i18B)
This machine is intended for commercial use. It is designed exclusively to scrub hard floors in an indoor environment and is not constructed for any other use.Only use recommended accessories.
All operators should read, understand and exercise the following safety precautions:

WARNING:Batteries may emit hydrogen gas. Explosion or fire can result from hydrogen gas. Keep sparks and open flames away! Keep battery compartment open when charging(except maintenance-free batteries).

1. Do not operate machine:
Unless trained and authorized. Unless you have read and understood the
operator’s manual. ±,QÀDPPDEOHRUH[SORVLYHDUHDV If not in proper operating condition. In outdoor areas and standing water.

WARNING:Flammable materials can cause an explosion or fire. Do not XVHÀDPPDEOHPDWHULDOVLQWDQNV

2. Before operating machine:

Make sure all safety devices are in place and operating properly.
3. When using machine:

WARNING:Flammable materials or reactive mentals can cause explosion or ¿UH’RQRWSLFNWKHPXS

Go slow on inclines and slippery surfaces. Follow all safety guidelines. ± 5HSRUW DQG ¿[ DQ GDPDJH WR PDFKLQH SULRU
to operating it. Never allow children to play on or around
the machine. Do not operate on inclines that exceed
2%(3°).

4. Before leaving or servicing machine:
Stop on level surface. ±7XUQRPDFKLQH

5. When servicing machine:
Read operator’s manual thoroughly prior to operating or servicing this machine.
Use manufacturer supplied or approved replacement parts.
Secure machine with wheel blocks prior to jacking the machine up.
Use approved jack or hoist to safety elevate the machine.
Disconnect batteries prior to working on machine.
Wear gloves when handling batteries or battery cables.
Avoid any contact with battery acid. ±$YRLGPRYLQJSDUWV’RQRWZHDUORRVH¿WWLQJ clothing while servicing machine.

i18B/i18C

OPERATOR MANUAL SAFETY PRECAUTIONS(FOR i18C)

WARNING:Carefully read and understand this manual before operating this machine. This scrubbing machine shall be grounded while in use to protect the operator from electric shock.Grounding provides a path of least resistance for electric current. This machine is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. Do not remove the ground pin under any circumstances.
This machine is for use on a nominal 110-volt circuit and has a grounding plug that resembles the plug illustrated in Figure. Make sure that the machine is FRQQHFWHG WR DQ RXWOHW KDYLQJ WKH VDPH FRQ¿JXUDWLRQ as the plug. No adapter should be used with this machine.

This machine is intended for commercial use. It is constructed for use in an indoor environment

and is nor intended for any other use. Use only recommended accessories.

1. Do not operate machine:

Unless trained and authorized.

Unless you have read and

±,QÀDPPDEOHRUH[SORVLYHDUHDVXQGHUVWRRGWKHRSHUDWRU
VPDQXDO

With a damaged cord or plug

With the use of extension cords.

If not in proper operating condition.

In outdoor areas and standing water.

2. Before operating machine: Make sure all safety devices are in place and operating properly.

3. When using machine: Do not run machine over cord. Do not pull cord around
sharp edges or corners. Do not handle plug with wet hands. Report machine damage or fault
operation immediately.

Do not pull machine by cord or plug. Do not unplug by pulling on the cord. Do not stretch cord. Keep cord away from heated surfaces.

4. Before leaving or servicing machine: ±7XUQRPDFKLQH±8QSOXJFRUGIURPRXWOHW

5. When servicing machine: Unplug cord from outlet.

Use manufacturer supplied or approved replacement parts.

WARNING:To avoid electrical shock,please replace the power cord immediately if any damage is being detected. The replacement must be performed only by an authorized person or by our customer service center.

WARNING:Flammable materials can cause explosion or fire. Do not use flammable materials in tanks or pick them up.

i18B/i18C

OPERATOR MANUAL
MACHINE COMPONENTS

9 22*
20 23 21 i18B

20 23 21

i18C

13 11
3

16 4

24* 24** 18 19

1. Brush cover 4. Recovery tank 7. Squeegee 10. Adjusting handle 13. Squeegee lifting handle 16. Brush plunger 19. Clear tube
22*. Battey monitor 24**. Power cord
6

10 12

6 11

2. Brush 5. Solution tank 8. Control box 11. Water filter 14. Power cord hook 17. Plug of water filling port 20. Switch for brush motor 23. Circuit breaker
25. Adjustable wheel

3. Cover tank 6. 8″ wheels 9. Trigger 12. Ball valve 15. Brush/pad driving hub 18. Knob 21. Switch for vacuum motor
24*. Charger power cord

* : only for i18B **:only for i18C
i18B/i18C

OPERATOR MANUAL
MACHINE SET UP & INSTALLATION

UNPACK MACHINE:
Be sure and check packing carton for any damage. Immediately report any damage to carrier. Be careful not to let machine vibrate while carrying, Check contents of package to ensure that the following items are included: Machine, squeegee assembly, brush/pad driver, charger cord.
MACHINE SET UP & PRE-OPERATION CHECKS:
1) Sweep the outside of the machine. 2) Check battery meter to make sure batteries are fully charged (see battery charging, only for i18B ). 3) Check that squeegee and brush / pad is properly installed. 4) The forward speed of machine can be controlled by turning the handle(10). Turn the handle
clockwise to speed up machine. or turn the handle anticlockwise to slow down machine. 0DNHVXUHWKHZRUNLQJVXUIDFHFDQVXSSRUWWKHPDFKLQHZHLJKWWKHJUDGLHQWRIWKHÀRRUFDQ¶W
exceed the limit that machine allowed(2%).
INSTALLING PAD DRIVER OR BRUSH:
7XUQRPDFKLQH 2) Tilt the machine backwards, line up the driving hub with the hole of brush or pad driver, make VXUHWKHWKUHHEORFNVDUH¿WWHGLQWRWKHWKUHHVORWVRIWKHGULYHKXE
,IDSDGGULYHULVEHLQJXVHGWKHDSSURSULDWHSDGVKRXOGEHDWWDFKHGWRWKHSDGGULYHU¿UVW 3) Push the plunger which on the brush cover to prevent the driving hub from rotating,then spin
the brush/pad clockwise with your another hand till the clip clamp the block on the brush/pad.
INSTALLING THE SQUEEGEE:
1) Loosen the two knobs(18) on the squeegee and slide the squeegee into the slots at the rear of the squeegee bracket. (the wheels on the squeegee point to the machine.)
2) Tighten the knobs securely.
FILLING THE SOLUTION TANK:
7KH¿OOSRUWLVORFDWHGDWWKHUHDURIPDFKLQHSXOOWKHSOXJRXWRIWKHKROH 2) Fill solution tank with water. (use a hose which link to a water faucet,water temperature
should not exceed 50° C) The clear tube(19) in the back right of the machine has gallon markers to help determine the water level in the solution tank(5). *Convertional scrubbing – Fill solution tank with water (not to exceed 60°C/140°F. Pour a recommended cleaning detergent into the solution tank according to mixing instructions on the container)
:$51,1*’RQRWSXWDQÀDPPDEOHPDWHULDOVLQWRVROXWLRQWDQN7KLVFDQFDXVH an explosion or a fire. Only use recommended cleaning chemicals. Contact your janitorial supply distributor for recommendations on proper chemicals.

i18B/i18C

OPERATOR MANUAL
MACHINE OPERATION
WARNING:Do not operate machine unless you have read and understand this manual. /RZHUVTXHHJHHDVVHPEOWRWKHÀRRUEVSLQWKHVTXHHJHHOLIWLQJKDQGOH 2) Turn brush motor switch(20) to “on” position. 3) Turn vacuum motor switch(21) to “on” position. 5RWDWH WKH EDOO YDOYH KDQGOH WR YHUWLFDO SRVLWLRQ 6ROXWLRQ ZLOO QRW EHJLQ WR ÀRZ XQWLO WKH operating triggers (9) are pulled. 5) To begin scrubbing, pull on the blue operating trigger(9), when this triggers is pulled, the pad GULYHUZLOOEHJLQWRVSLQDQGWKHVROXWLRQZLOOEHJLQWRÀRZ 6) Begin scrubbing by moving the machine forward $GMXVWVROXWLRQÀRZEDGMXVWLQJWKHSRVLWLRQRIEDOOYDOYHNQRE
WARNING:Do not keep the machine in the same position with the pad / EUXVKVSLQQLQJRURXPLJKWGDPDJHWKHÀRRU
WHILE OPERATING MACHINE
1) Occasionally open the cover tank(3) to see if there is any foam build-up. If excessive foam is found, add defoamer to the recovery tank.
:$51,1*)RDPPXVWQRWHQWHUWKHÀRDWVKXWRVFUHHQRUGDPDJHFDQRFFXUWR WKHYDFXXPPRWRU)RDPZLOOQRWDFWLYDWHWKHPDFKLQH
VÀRDWVKXWRGHYLFH 2) Occasionally view the clear tube at the back left of the machine to check the amount of cleaning VROXWLRQWKDWLVOHIWLQWKHPDFKLQH,IWKHVTXHHJHHDVVHPEOOHDYHVVWUHDNVRQWKHÀRRUUDLVH WKHVTXHHJHHRWKHÀRRUDQGZLSHWKHEODGHVGRZQZLWKDGDPSFORWK
WARNING:Do not use your fingers to wipe or remove debris from the blades, as injury may occur. :KHQ WKH VROXWLRQ WDQN UXQV HPSW WXUQ R WKH EUXVK VZLWFK DQG EDOO YDOYH RI VROXWLRQ WDQN Keep the squeegee down and continue to vacuum until all the dirty water is picked up.

TANK DRAINING
7XUQWKHVZLWFKHVRQWKHFRQWUROSDQHOWR³R´SRVLWLRQ 2) Raise the squeegee, transport machine to approved area for draining tank(s).
:$51,1*$Q WLPH VFUXEELQJ LV FRPSOHWHG RU ZKHQ UH¿OOLQJ VROXWLRQ WDQN WKH recovery tank should be drained and cleaned.
WARNING:If the recovery tank is not drained when the solution tank has been UH¿OOHGIRDPRUZDWHUPDHQWHUWKHÀRDWVKXWRPHFKDQLVPDQGFDXVHGDPDJH to the vacuum motor.

i18B/i18C

OPERATOR MANUAL
DRAINING THE RECOVERY (DIRTY) TANK
5HPRYHWKHGUDLQKRVHIURPWKHKROGHUDQGSODFHWKHGUDLQKRVHRYHUWKHÀRRUGUDLQ 7ZLVWRWKHGUDLQKRVHSOXJWREHJLQWKHGUDLQLQJSURFHVV 2) Clean the recovery tank after every use. Use a fresh water hose to rinse out the recovery WDQN%HFDUHIXOQRWWRVSUDZDWHULQWRWKHÀRDWVKXWRPHFKDQLVP
WARNING:If you are storing the machine for any period of time, keep the cover tank open so the tank can dry completely and smell fresh.
DRAINING THE SOLUTION (CLEAN) TANK
WARNING:Any time scrubbing operation is completed, the solution tank should be drained and cleaned.
1) Pull down on the clear tube (back left of the machine) to remove it from the hose barb. This ZLOODOORZWKHVROXWLRQWRÀRZIUHHOLQWRDEXFNHWRUÀRRUGUDLQ 2) Rinse the solution tank with clean water after every use. This will help prevent chemical buildup and clogging of the solution lines. 2QFHWDQNLVULQVHGÀXVKHGDQGGUDLQHGUHFRQQHFWWKHFOHDUWXEHWRWKHKRVHEDUE%H sure the tube is pushed all the way up on the hose barb. 6FUHZRWKHFRYHURIWKHZDWHU¿OWHUWRFRPSHOHWOH[KDXVWWKHWDQNDQGFKHFNWKH¿OWHU screen, clean it up if necessary. 6FUHZXSWKHFRYHURIWKHZDWHU¿OWHUEXVXUHWRLQVWDOOWKHVFUHHQDQGWKH2ULQJLQWKH correct position.

¿OWHUVFUHHQ
2ULQJ
¿OWHUFRYHU
BATTERY CHARGING (ONLY FOR i18B)
Each machine was equipped with on-board charger and batteries, please use oringinal parts only.
WARNNING: Fire or explosion hazard. Batteries may emit hydrogen gas. Keep sparks and open flame away. Keep battery compartment open when 127(8VHRQODSSURYHGFKDUJHUVZLWKWKHIROORZLQJVSHFL¿FDWLRQV $XWRPDWLFVKXWRFLUFXLW – Deep cycle charging. – Output current of 8-15 Amps. – Output voltage of 24 volts.

i18B/i18C

OPERATOR MANUAL

Battery Indicator Description:

Green lights on: full power. <HOORZOLJKWVRQJUHHQOLJKWVRPHGLXPSRZHU 5HGOLJKWRQRWKHUOLJKWVRSRZHUWKH maichine should be stopped and the batteries
should be recharged. 5HGOLJKWÀDVKWKHEDWWHULHVKDYHDOUHDGEHHQ discharged deeply.

NOTE:Frequently deep discharging will reduce the life of the batteries, charge the batteries when Red Yellow 2 Ye l l o w Green 2 Green 1 the red light is on.

1) Place the machine in a well ventilated area. 7XUQWKHPDFKLQHR ,IFKDUJLQJZHWOHDGDFLGEDWWHULHVFKHFNWKHÀXLGOHYHOEHIRUHFKDUJLQJ 4) Connect the charger’s AC power supply cord to a properly grounded receptacle. 5) The charger will automatically begin to charge and will automatically shut off once the
batteries are fully charged. 6) Upon completion of charging, disconnect the AC power supply cord.
NOTE: The charging status can be seen through the lights behind the transparent panel: Yellow light on: Normal charging *UHHQOLJKWÀDVKFKDUJHG Green light on: Fully charged, batteries ready for use. <HOORZOLJKWVÀDVK1REDWWHULHVRULQFRUUHFWZLULQJ
PREVENTATIVE MAINTENANCE

WARNNING: Before performing any maintenance on the machine, be sure WKDWWKHSRZHULVWXUQHGRRUWKHEDWWHULHVDUHGLVFRQQHFWHG
WARNNING: Repairs are to be completed by authorized service centers only. Any repairs completed by unauthorized persons will avoid the warranty.
DAILY MAINTENANCE
1) Remove pad driver / brush and clean with approved cleaner. 2) Drain recovery and solution tanks completely and rinse out with clean water. Visually check
the recovery tank for debris and clean out as necessary. 5DLVHVTXHHJHHDVVHPEORÀRRUDQGZLSHLWGRZQZLWKDGDPSWRZHO%HVXUHWRVWRUHWKH
squeegee in the up position. 5HPRYHWKHÀRDWVKXWRDVVHPEODQGULQVHLWRXWZLWKFOHDQZDWHU &OHDQPDFKLQHZLWKDQDSSURYHGFOHDQHUDQGDGDPSWRZHO’RQ¶WVSUDZDWHUWRFOHDQWKH
outside of machine to avoid damage to motor and wiring. 8QSOXJYDFXXPPRWRUIURPSRZHUVRXUFHDQGKRVHFX UHPRYHWKHGUDLQKRVHIURPWKH
holder prior to removing the recovery tank when performing maintenance. 7) Check the condition of the squeegee blade wiping edge, rotate blade or replace it if worn.

i18B/i18C

OPERATOR MANUAL
MONTHLY MAINTENANCE
1) Clean the battery tops to prevent corrosion (only for i18B). 2) Check for loose battery cable connections (only for i18B). 3) Inspect and clean the recovery tank cover seal. Replace it if damaged. 4) Lubricate all grease points and pivot points with silicon spay and approved grease. 5) Check the machine for loose nuts and bolts. 6) Check the machine for leaks. 7) Battery must be stored in a charged state, please charge monthly.
MOTOR MAINTENANCE
1) Contact your local ICE Distributor for any motor maintenance. 2) Check the motor brushes every 250 hours, Replace the brushes when they are worn to a
length of 10mm or less.
BATTERY MAINTENANCE (ONLY FOR i18B)
:$511,1* %DWWHULHV PD HPLW KGURJHQ JDV DQG DQ H[SORVLRQ RU ¿UH FDQ UHVXOW.HHSVSDUNVDQG¿UHDZDIURPEDWWHULHVDWDOOWLPHV
WARNNING: Whenever servicing batteries, be sure to wear protective gloves. Avoid contact with battery acid at all times.
Note: For the best machine performance, keep batteries charged at all times.Do not let them sit in a discharged condition. 1) Always follow the battery charging direction as outlined in the BATTERY CHARGING section of this manual. 2) Keep battery tops and terminals free from corrosion. A strong solutin of baking soda and water is the best way to keep the batteries corrosion free. DO NOT ALLOW THE BAKING SODA / WATER SOLUTION TO ENTER THE BATTERY CELLS. 3) Use a wire brush with the baking soda solution to properly clean the battery posts and
connections. 4) Check battery connections for wear and loose terminals. Replace them if necessary.
MACHINE STORAGE
1) Always store the machine indoors and in its upright position. 2) Always store the machine in a dry area. $OZDVWDNHRWKHSDGGULYHUEUXVKEHIRUHVWRUDJH $OZDVVWRUHWKHPDFKLQHZLWKWKHVTXHHJHHDVVHPEOUDLVHGRWKHÀRRU ,IVWRULQJLQDQDUHDZKLFKPDUHDFKIUHH]LQJWHPSHUDWXUHVEHVXUHWRGUDLQDOOÀXLGVIURP WKHPDFKLQHSULRUWRVWRUDJHLQFOXGHWKH¿OWHU$QGDPDJHFDXVHGEIUHH]LQJWHPSHUDWXUHV will not be covered by the warranty. ‘UDLQWKHUHFRYHUWDQNDQGNHHSWKHFRYHUWDQNRSHQVRWKDWLWFDQEUHDWKHGXULQJVWRUDJH ‘UDLQWKHVROXWLRQWDQNRIDOOÀXLG

i18B/i18C

OPERATOR MANUAL

BASIC TROUBLESHOOTING

PROBLEM

CAUSE

SOLUTION

No Power

The wiring not connected correctly or bad wiring
Bad brush motor

Check the wiring or contact ICE Distributor Contact ICE Distributor

Carbon brushes worn out Contact ICE Distributor

The wiring not connected

Vacuum correctly or bad wiring

motor does

not run

Bad vacuum motor

Carbon brushes worn out

Little or no solution ÀRZ

Bad ball valve Bad solution valve
Ball valve position in need of adjustment

Check the wiring or contact ICE Distributor
Contact ICE Distributor Contact ICE Distributor Contact ICE Distributor Contact ICE Distributor When ball valve is in horizontal position,the DPRXQWRIVROXWLRQÀRZLVPD[LPXP

Squeegee clogged Squeegee blades worn

&OHDQGHEULVRVTXHHJHHZLWKDGDPSWRZHO Install new squeegee blades

Squeegee not mounted correctly

&RQ¿UPWKDWWKHVTXHHJHHDVVHPEOLVVHFXUHO IDVWHQHGWRWKHPDFKLQHDQGQRWORRVH¿WWLQJ

Poor water pick up

Vacuum hoses have a hole Check hose connections and make sure they

or are loose

DUH¿UP5HSODFHKRVHLIGDPDJHG

Vacuum hose may be clogged

Check hose for debris and remove any clog.

Drain hose stopper is loose Tighten drain plug.

Vacuum motor is loose

Tighten vac motor mounting screws. Do not over tighten or damage will occur.

cover tank is loose

&RQ¿UPWKHFRYHUWDQNLVVHFXUHOLQLWVSODFH

short runtime*

Recovery tank is full

Drain recovery tank

)ORDWVKXWRLVFORJJHG

5HPRYHÀRDWVKXWRIURPLQVLGHUHFRYHUWDQN and remove any debris

Low battery charge

Fully recharge batteries

Defective batteries

Replace batteries

Batteries need maintenance See BATTERY MAINTENANCE

Faulty battery charger

Repair or replace battery charger

* ONLY FOR i18B

i18B/i18C

OPERATOR MANUAL TECHNICAL SPECIFICATION

ITEM
Working Width Squeegee Width Productivity rate
Brush Dia. Brush Speed Max Pad Pressure Voltage Brush Motor Vacuum Motor Batteries Solution Tank Capacity Recovery Tank Capacity Machine Weight (w/o batteries) Batteries Weight Machine Length Machine Height Machine Width Power cord Length Charger cord length Max Gradient Type of Drive Noise Level
WATER LIFT – AIR FLOW

i18B

i18C

18in / 450mm

30in / 762mm

16145 ft2h / 1500m2h

12915 ft2h / 1200m2h

18in / 450mm

180rpm

55lbs / 25kg

24VDC

120VAC

0.75hp / 550W

0.7hp / 500W

2-12V, 85AH @20hr

N/A

9.25Gal / 35L

10.57Gal / 40L

138lbs / 62.5kg

110lbs / 50kg

N/A

45.87in / 1165mm

40.35 in / 1025mm

20.5in / 520mm

N/A

82ft / 25m

8.2ft / 2.5m

Brush assisted

70 dB

45 IN.H2O

i18B/i18C

PART LISTS

RECOVERY TANK ASSEMBLY

24 16 26

20 19
4 18
16 14
28

i18B/i18C

RECOVERY TANK ASSEMBLY

PART LISTS

DIA PART NO. number

DESCRIPTION

8011001 RECOVERY TANK 1
8016001 RECOVERY TANK

SERIAL NUMBER 60003100364~60003100853 50010100124~50010100713 60003100945~60012103001~ 50010100714~51010101228~

2 8011011 DECAL,LEFT

3 4010316 ICE LOGO

8131030 DRAIN HOSE 4
8131031 DRAIN HOSE

60003100958~60012102302 50010100724~51010101128
60012102343~51010101129~

5 1962050 HOSE CLAMP 27-51mm

8011006 VACUUM HOSE
6
8011060 SUCTION PIPE

60003100945~60012102405 50010100713~51010101150 60012102457~ 50010100713~51010101150~

8132006 CARBON BRUSH (FRO i18B)

7 8112008 CARBON BRUSH (FRO i18B)

8011022 CARBON BRUSH (FRO i18C)

8 1113608 SELFLOCKING NUT M6

9 1411612 3/$,1:$6+(5îî

10 8011007 MUFFLER

8132050 AMETEK VACUUM MOTOR , KIT, 24VDC 60003100101~60003100364

11 8112100 VACUUM MOTOR 24V, KIT (FRO i18B) 60003100365~60012103001~

8011200

VACUUM MOTOR 110V, 500W, KIT (FRO i18C)

50010100124~51010101228~

12 8112005 GASKET

13 8112006 BOLT

14 1111605 HEX NUT M6

15 1021616 +(;+($’%2/70î

16 1421618 3/$,1:$6+(5îî

17 8111300 HINGE ASSEMBLY

18 8011012 DECAL,RIGHT

19 8011009 PLATE

20 1421409 3/$,1:$6+(5îî66

21 1221410 3+6&5(:0î66

22 8111015 FLOAT CAGE

23 8111014 FLITER COUPLING

24 8111001 GASKET

25 1321110 $8727$33,1*6&5(:67î

26 1421612 3/$,1:$6+(5îî
8131003 CAP 27
8131004 CAP

60003100364~60012102611 50010100713~51010101150 60012102612~51010101151~

28 8011013 CABLE

Note: NO 14711Supplier change, code update. NO 277KHUHVXOWVDUHRSWLPL]HGDQGZLOODOVR¿WROGHUPDFKLQHV

NO REQ’D
1
1
1 3
1
1 2
1
1
2 2 2 3 5 1 1 1
1
1 3 3 10 10 2 1 2 5 2 1 1 1 1 2
1
1 1

i18B/i18C

PART LISTS

COVER TANK ASSEMBLY

DIA NO.
1
2
3
4

PART number
8012005 8012001 8111022 8012003 8011005 8012002
8012002A

DESCRIPTION
COVER TANK WARNING LABLE WARNING LABLE (FOR i18B) WARNING LABLE (FOR i18C) CAP GASKET
GASKET

Note: DIA NO 4:Supplier change, code update.

SERIAL NUMBERNUMBER
50010000124~50010100713 60003000364~60012103001~ 51010101150~
60003100471~60012103001~ 50010100557~51010101228~

NO REQ’D
1 1 1 1 1 1
i18B/i18C

SOLUTION TANK ASSEMBLY

PART LISTS

31 3

26 28 27

6
8 24

10 17 18
15 19

i18B/i18C

PART LISTS

SOLUTION TANK ASSEMBLY

DIA PART NO. number

DESCRIPTION

1 8114750 BATTERY CABLE(I18B)

8050476

CABLE ASSEMBLY WITH CONNECTOR(RED i18B)

8050476-1

CONNECTOR,BATTERY,RED ANDERSON 5916G7(i18B)

8013001 SOLUTION TANK

3 8017001 SOLUTION TANK

8133033

SOLUTION TANK(I18B,I18C REPLACE THE OLD WATER TANK 8013001)

4 8013010 12V BATTERY(FOR i18B)

5 1321110 $8727$33,1*6&5(:67î

6 1421409 3/$,1:$6+(5îî

7 8133002 PLUG

8 8013005 TRANSPARENT HOSE

9 8034012 BRACKET, CASTER

10 8013016 &$6725

11 1421618 3/$,1:$6+(5îî

12 1422616 SPRING WASHER 6 SS

13 1021616 +(;+($’6&5(:0î66

14 1021830 +(;+($’6&5(:0î66

15 1422821 SPRING WASHER 8

16 1421824 3/$,1:$6+(5îî

17 8016010 WHEEL SHAFT

18 1421816 3/$,1:$6+(5îî

19 1021820 +(;+($’6&5(:0î66

8115200 :+((/ 1612607 BALL BEARING, 6004LU

21 1421828 3/$,1:$6+(5îî

22 8115203 WHEEL CAP

23 1962032 HOSE CLAMP

24 8013009 DECAL,RIGHT

25 8013002 BACKET

26 1221510 3+6&5(:0î66

27 1421510 3/$,1:$6+(5îî66

28 8113009 WIRE CLAMP

29 8114751 WIRING BOOT(FOR i18B)

30 8013008 DECAL,LEFT

8050475

CABLE ASSEMBLY WITH CONNECTOR(BLACK i18B)

8050475-1

CONNECTOR,BATTERY,BLACK ANDERSON 5916G4(i18B)

SERIAL NUMBERNUMBER
60003000364~60003000853 50010000124~50010000713 60003100945~60012103001~ 50010100713~51010101228~

NO REQ’D
1
1
1
1
1
1
2 1 1 1 1 1 1 3 3 3 1 3 1 1 2 4 2 4 2 2 1 1 1 4 4 4 4 1
1
1

Note: ‘,$127KHUHVXOWVDUHRSWLPL]HGDQGZLOODOVR¿WROGHUPDFKLQHV

i18B/i18C

CONTROL BOX ASSEMBLY (FOR i18B)

PART LISTS

i18B/i18C

PART LISTS

CONTROL BOX ASSEMBLY(FOR I18B)

DIA PART NO. number

DESCRIPTION

SERIAL NUMBERNUMBER

NO REQ’D

1 8014062 REAR PANEL

2 1421512 3/$,1:$6+5(îî

3 1211516 3+6&5(:0î

4 1421409 3/$,1:$6+(5îî

5 8114707 RELAY

6 1113305 SELFLOCKING NUT M3

7 8014061 SWITCH BRACKET

8 1411309 3/$,1:$6+(5îî

9 8014034 BRCKET

10 1411824 3/$,1:$6+(5îî

11 1021820 +(;+($’%2/70î

12 8114030 FIXING BRACKET,CONTROL BOX

13 8014076 BATTERY CHARGER 24V

14 8113104 HANDLE

6210111 HOSE CLAMP 15
6210120 HOSE CLAMP

60003000364~60003000534

60003101551~60012103001~ 1

16 1221416 3+6&5(:0î66

17 8014010 SQUEEGEE LIFTING HANDLE

18 8014008 CONTROL BOX

8014013 SQUEEGEE LIFTING ROPE 8034010 SQUEEGEE LIFTING ROPE

~60003000515~60012000614 1 1

20 8114511 JOINT BEARING SQ6

21 1421618 3/$,1:$6+(5îî66

22 1121605 HEX NUT M6

23 1421828 3/$,1:$6+(5îî

24 1021830 +(;+($’%2/70î

25 1221512 3+6&5(:0î66

26 8114005 PIPE COUPLING

27 8112030A CHARGER CORD (FOR US)

28 8014038 GASKET

29 8014036 PANEL

30 8014044 PLATE

31 1221516 3+6&5(:0î66

32 1123608 SELFLOCKING NUT M6,SS

33 8114703 OVERLOAD PROTECTOR 35A

34 1421518 3/$,1:$6+(5îî

35 1021512 +(;+($’%2/70î66

36 8034011 BAFFLE

37 8014101 LIFTING ROPE SPACER

38 1021630 +(;+($’%2/70î66

39 8014045 TRANSPARENT PLATE

40 8014006 WATERPROOF SWITCH 250V 16A

i18B/i18C

CONTROL BOX ASSEMBLY(FOR I18B)

PART LISTS

DIA PART NO. number

DESCRIPTION

41 8014043 WIRE BUFFER 42 8014041 WIRE CLAMP 43 1221616 3+6&5(:0î66 44 2320403 STRAIN RELIEF 45 8014063 BATTERY CAPACITY INDICATOR

46 1221410 3+6&5(:0î66 47 8014067 PANEL DECAL 48 8014069 FRONT PANEL 49 8114101 SHAFT

50 8014004 GASKET 51 1221412 3+6&5(:0î66 52 1432411 SPRING WASHER 4 53 1411409 3/$,1:$6+(5îî 54 8014022 CONTROL TRIGGER 55 8014033 PLATE 56 1534608 6(76&5(:0î 57 8014031 HEX BUSHING

58 8014032 SPRING ROD 59 8014035 SPRING 60 1211320 3+6&5(:0î 61 1434300 WASHER WITH TOOTH 3

62 8114712 MICROSWITCH 63 1113507 SELFLOCKING NUT M5

64 8210421 RELAY 24VDC 30A

65 1123406 SELFLOCKING NUT M4, SS

SERIAL NUMBERNUMBER

NO REQ’D
1 1 1 1 1 15 1 1 1 1 4 2 2 1 1 4 1 1 1 2 2 1 7 1 2

Note: DIA NO 1519:Supplier change, code update.

i18B/i18C

PART LISTS

CONTROL BOX ASSEMBLY (FOR i18C)
48 47 46 45 44 43

49 50 51 52 27

59 60

19 58

56
57 3 4 5

6 7

8 9 10
11

42 41 40 39 38 37
36
35 34 33 32 31
30
29 28 27 26 25 24 23 22
21 20

13 14

15 16 17 18 19

i18B/i18C

PART LISTS

CONTROL BOX ASSEMBLY(FOR I18C)

DIA PART NO. number

DESCRIPTION

1 1421409 3/$,1:$6+(5îî 2 1211516 3+6&5(:0î 3 1113305 SELFLOCKING NUT M3 4 1021820 +(;+($’%2/70î 5 1411824 3/$,1:$6+(5îî 6 1113507 SELFLOCKING NUT M5
7 8114030 FIXING BRACKET,CONTROL BOX
8 8113104 HANDLE

SERIAL NUMBERNUMBER

NO REQ’D
11 4 2 6 6 4 1 1

6210111 HOSE CLAMP 9
6210120 HOSE CLAMP

50010000430~50010100924

50010100943~51010101228~

10 1221416 3+6&5(:0î66

11 8014010 SQUEEGEE LIFTING HANDLE

12 8014008 CONTROL BOX

8014013 SQUEEGEE LIFTING ROPE 13
8034010 SQUEEGEE LIFTING ROPE

~50010100629~51010101227 1 50010100724~51010101228~ 1

14 8114511 JOINT BEARING SQ6

15 1421618 3/$,1:$6+(5îî66

16 1121605 HEX NUT M6

17 1421828 3/$,1:$6+(5îî

18 1021830 +(;+($’%2/70î

19 1221512 3+6&5(:0î

20 1221516 3+6&5(:0î66

21 8014044 PLATE

22 8114005 PIPE COUPLING

23 8014037 PANEL, BOTTOM

24 8014038 GASKET

25 8014068 OVERLOAD PROTECTOR 10A

8014053

Power Cord, 82’ Resistant (18C)

14AWG Water

8014058 Pigtail Kit (i18C)

27 1221410 3+6&5(:0î66

28 1123608 SELFLOCKING NUT M6,SS

29 8034011 BAFFLE

30 1421512 3/$,1:$6+5(îî

31 1021512 +(;+($’%2/70î66

32 8014101 LIFTING ROPE SPACER

33 1021630 +(;+($’%2/70î66

34 8014006 WATERPROOF SWITCH 250V 16A

35 8014041 WIRE CLAMP

i18B/i18C

PART LISTS

CONTROL BOX ASSEMBLY(FOR I18C)

DIA PART NO. number

DESCRIPTION

36 8014043 WIRE BUFFER 37 1221614 3+6&5(:0î 38 1422616 SPRING WASHER 6 39 2320403 STRAIN RELIEF 40 8014007 PANEL DECAL 41 8014005 FRONT PANEL 42 8014004 GASKET 43 8114101 SHAFT 44 1221412 3+6&5(:0î66 45 1411409 3/$,1:$6+5(îî 46 1432411 SPRING WASHER 4 47 8014033 PLATE 48 8014022 CONTROL TRIGGER 49 1534608 6(76&5(:0î 50 8014031 HEX BUSHING 51 8014032 SPRING ROD 52 8014035 SPRING 53 1211325 3+6&5(:0î 54 1411309 3/$,1:$6+(5îî 55 8014071 SWITCH 56 8014061 SWITCH BRACKET 57 8014002 REAR PANEL 58 8014034 BRACKET 59 6210423 RECTIFIER 60 1421510 3/$,1:$6+(5îî66 61 1123507 LOCK NUT M5

Note: DIA NO 913:Supplier change, code update

SERIAL NUMBERNUMBER

NO REQ’D
1 1 1 1 1 1 1 1 2 2 2 1 1 4 1 1 1 2 4 1 1 1 1 1 1 1

i18B/i18C

SCRUB HEAD GROUP

PART LISTS

i18B/i18C

PART LISTS

SCRUB HEAD GROUP

DIA PART NO. number

DESCRIPTION

8015200 MOTOR 24V 550W, KIT(FOR i18B)

8015220

MOTOR 120V 550W, KIT(FOR i18C)

2 8015020 ADJUSTING HANDLE

3 8015010 BRUSH HANGER

4 1511065 +(;62&.(76&5(:0î 5 1644220 3,1î

6 8015101 DECAL

7 1111008 HEX NUT M10

8 8015104 BEARING GEC6C

9 8015105 BEARING HOUSING

10 1439005 DETENT RING 5

11 8015087 ASSAMBLY BOARD

12 8015050 BRUSH PLUNGER

13 1123810 SELFLOCKING NUT M8,SS

14 1421816 3/$,1:$6+(5îî66 15 8115404 SPACER

16 8116009 BUMPING WHEEL

17 8111023 WARNING DECAL

18 1221512 3+6&5(:0î 19 1421510 3/$,1:$6+(5îî66

20 8116002 WASHER

21 8116003 SPRING CLAMP

22 8116008 BRUSH HUB

9050018 %586+ 24 1421828 3/$,1:$6+(5îî

25 8015090 SPLASH GUARD

26 1422821 SPRING WASHER 8

27 1023810 +(;+($’%2/7î66 28 1021835 +(;+($’%2/70î66

29 1111215 HEX NUT M16

30 8015108 SUPPORTER

31 1011016 +(;%2/70î

32 1411020 3/$,1:$6+(5îî 33 1011625 +(;+($’%2/70î 34 1421618 3/$,1:$6+(5îî66 35 1221510 6+6&5(:0î

36 1212410 6+6&5(:0î 37 8015060 WATER INLET

38 8015041 MOTOR BRACKET

39 8015005 BRUSH COVER

40 1222510 6+6&5(:0î 41 1421518 3/$,1:$6+(5îî66

42 1422513 SPRING WASHER 5

43 1221515 3+6&5(:0î 44 1221616 3+6&5(:0î

SERIAL NUMBERNUMBER

NO REQ’D
1
1
1 1 1 2 1 1 1 1 1 1 1 1 3 1 1 1 2 2 1 1 1 1 1 1 1 1 1 1 1 1 4 4 8 1 2 1 1 1 2 4 5 3 8
i18B/i18C

PART LISTS

SCRUB HEAD GROUP

DIA NO.
45 46
47
48 49 50 51 52 53 54 55 56 57 58 59 60 61

PART number
8015103 1221410
1321213
1646240 8015116 8015001 1123608 1511040 8015007 1113012 8015115 8015121 8015002 8116004 1656432 8015003 8115004

DESCRIPTION
VALVE BRACKET 3+6&5(:0î66 AUTO TAPPING SCREW 67î &277(53,1î 1</21:$6+(5îî BRACKET SELFLOCKING NUT M6,SS +(;62&.(76&5(:0î BUSHING SELFLOCKING NUT M10 1</21:$6+(5îî 63$&(5îî BRACKET DETENT RING .(<î 63$&(5îî SPRING

SERIAL NUMBERNUMBER

NO REQ’D
1 2
2
2 4 1 4 2 3 1 2 1 1 1 1 1 1

DIA PART NO. number

DESCRIPTION

1 9050018 %586+

2 9040017 3$”5,9(5

3 9000001 BIG MOUTH

SERIAL NUMBERNUMBER

NO REQ’D
1 1 1

i18B/i18C

PART LISTS

SQUEEGEE HOLDER ASSEMBLY (NEW)

i18B/i18C

PART LISTS

SQUEEGEE HOLDER ASSEMBLY(NEW)

DIA PART NO. number

DESCRIPTION

1 8037020 BRACKET, SQUEEGEE MNTG

2 1421618 3/$,1:$6+(5îî

3 1422616 SPRING WASHER 6 SS

4 1021616 +(;+($’6&5(:0î66

5 1021230 +(;+($’%2/70î66

6 1421132 3/$,1:$6+(5îî

7 8135001 3/$67,&:$6+(5îî

8 8115004 SPRING

8115405 SLEEVEE, P/M 9
8115005 SLEEVEE, P/M

10 8037010 BRACKET, SQUEEGEE 11 1123115 SELFLOCKING NUTS M12 12 8115001 SQUEEGEE SUPPORT 13 8037015 3,1î 14 1645324 COTTER PIN

SERIAL NUMBERNUMBER
60003000364 50010000124~50010000518 60003000365~60012103001~ 50010000519~51010101228~

Note: NO 97KHUHVXOWVDUHRSWLPL]HGDQGZLOODOVR¿WROGHUPDFKLQHV

NO REQ’D
1 3 3 3 2 2 4 1
2
2
1 2 1 1 1

i18B/i18C

PART LISTS

SQUEEGEE HOLDER ASSEMBLY (OLD) 17

13 2

4
12 5

7 8

i18B/i18C

PART LISTS

SQUEEGEE HOLDER ASSEMBLY(OLD)

DIA PART NO. number

DESCRIPTION

1 8017003 SPRING

2 1411816 3/$,1:$6+(5îî

3 1432821 SPRING WASHER 8

4 1021820 +(;+($’%2/70î66

5 1021230 +(;+($’%2/70î66

6 8015117 1</21:$6+(5îî

7 8115001 SQUEEGEE SUPPORT

8 1123115 SELFLOCKING NUTS M12

9 8017010 SQUEEGEE BRACKET

10 8117006 CUSHION

11 8115005 63$&(5îî

12 8017002 SPRING

13 1644248 3,1î

14 1645324 COTTER PIN

15 8017024 SUPPORTING PIPE

16 8017020 SQUEEGEE HOLDER

17 1221550 3+6&5(:0î

18 8017005 BUSHING

19 1123507 SELF-LOCKING NUT M5

SERIAL NUMBERNUMBER

NO REQ’D
1 3 3 3 2 4 1 2 1 2 2 1 1 3 1 1 1 1 1

i18B/i18C

PART LISTS

SOLUTION SYSTEM ASSEMBLY

10 9 8 7

2 1
13

15 16

SOLUTION SYSTEM ASSEMBLY

DIA PART NO. number

DESCRIPTION

1 1962016 HOSE CLAMP

2 8018004 HOSE

8018007 SOLENOID VALVE, 24V (FOR i18B) 8018009 SOLENOID VALVE, 110V (FOR i18C)

4 8018003 HOSE

5 8119006 HOSE CLAMP

6 8119200 WATER FILTER

7 8018002 HOSE

8 8013007 JOINT

9 8018006 BALL VALVE

10 8013006 90º JOINT

11 8119101 FILTER BODY

12 1622765 O RING

13 8119104 FILTER SCREEN

14 8119102 FILTER COVER

15 1421409 3/$,1:$6+(5îî66

16 1221412 3+6&5(:0î66

SERIAL NUMBERNUMBER

NO REQ’D
2 1 1 1 1 4 1 1 1 1 1 1 1 1 1 2 2

i18B/i18C

SQUEEGEE ASSEMBLY

PART LISTS

i18B/i18C

PART LISTS

SQUEEGEE ASSEMBLY

DIA PART NO. NUMBER

DESCRIPTION

1123810 LOCK NUT M8

1421824 FLAT WASHER M8× 24×2.0

8116009 PROTECTIVE WHEEL

1021616 HEX BOLT M6×16

8115404 BEARING, JOURNAL

1421612 FLAT WASHER M6× 12×1.6

8118300 LEFT BRACKET

8118400 CASTER, 2 INCH

8118600 CLAMP ASSEMBLY, SQUEEGEE

8118022 SQUEEGEE BLADE, REAR, LINATEX

8118002

SQUEEGEE BLADE, REAR, PU (OPTION)

8118003 STAR KNOB M8

8118004 SQUEEGEE HOUSING

1021835 HEX BOLT M8×35

8118009 RETAINER,SQUEEGEE

8118008 SPACER

1222515 SCREW M5×15

8118010 RETAINER ASSEMBLY

8118021 SQUEEGEE BLADE, FRONT, LINATEX

8118001

S Q U E E G E E B L A D E , F R O N T, P U (OPTION)

8118610 SHORT CLAMP ASSEBLY

1221575 SCREW M5×75

8118200 RIGHT BRACKET

1121008 HEX NUT M10

23 8118600A CLAMP ASSEMBLY

8118624 SHAFT

8118623 SPACER

1123507 LOCK NUT M5

8011003 VACUUM HOSE 27
8011060 VACUUM HOSE

8118050 SQUEEGEE ASSEMBLY, LINATEX 28
8118051 SQUEEGEE ASSEMBLY, PU

Note: DIA NO 27:Supplier change, code update.

SERIAL NUMBER

NO REQ’D
2 4 2 2 2 2 1 2 1 1 1 4 1 2 1 1 6 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1
i18B/i18C

WEAR & TEAR PARTS LIST

DIA PART NO. NUMBER
1 8115200 2 8116009 3 8118022 4 8118021 5 9040017 6 9050018

DESCRIPTION
8 INCH WHEEL BUMPING WHEEL REAR SQUEEGEE FRONT SQUEEGEE 3$’+2/'(5
%586+

SERIAL NUMBER

PART LISTS
NO REQ’D
2 3 1 1 1 1

i18B/i18C

WIRING DIAGRAM

WIRING DIAGRAM(i18B)

i18B/i18C

WIRING DIAGRAM(i18C)

WIRING DIAGRAM

i18B/i18C

CERTIFICATE OF QUALIFIED
MODEL:__________ SERIAL NO.:__________

INSPECTOR:__________

DATE:__________

ICE Cobotics (GuangDong)Company Limited

TEL:(+86) 769 8186 9000 FAX:(+86) 769 8186 3000

Documents / Resources

ICE COBOTICS i18B Automatic Scrubber [pdf] Instruction Manual
i18B, i18C, i18B Automatic Scrubber, i18B, Automatic Scrubber, Scrubber

References

User Manual

ICE COBOTICS i18B Automatic Scrubber Instruction Manual

i18B Automatic Scrubber

Product Information

Specifications:

Product Usage Instructions

Safety Precautions:

i18B:

i18C:

Machine Components:

Machine Set Up & Installation:

FAQ

How do I order parts for the ICE Cobotics Automatic
Scrubber?

Documents / Resources

References

Leave a comment

Cancel reply