Thermal Network Bullet Camera & Turret Camera
V5.5.98 build 240726
Release Note
(2024-09-30)
1. Basic Information
| Firmware Version | V5.5.98 build240726 |
| SDK Version | V6.1.9.3 build20220126 |
| Play Lib | 7.4.2.41 |
| iVMS-4200 | V3.7.4.1 build20220412 |
| Web Component | V4.0.1.0 build 240426 |
| Perimeter Protection Algorithm Version | V1.9.4build20240229 |
| Fire Source Detection Algorithm Version | V4.0.2build20231109 |
| Temperature Measurement Algorithm Version | V2.1.9build20231211 |
| Smoke Detection Algorithm Version | V2.3.0build20220325 |
Key note:
V5.5.98build240726 mainly fixed temperature range display issue for 2608 camera.
V5.5.98build240528 mainly fixed temperature exception issue when device upgrade from V5.5.76 to V5.5.98build240426.
2. V5.5.98build240426 New Features
2.1 Support Bi-Spectrum analysis to avoid missing alarms in low temperature difference scene.
2.2 VCA performance optimization enhanced by distillation model.
2.3 Support Perimeter Protection Combined Event Alarm.
Setup line crossing as conditions of intrusion rules, the line crossing is triggered first, then intrusion is activated and triggered with alarm interval, then intrusion alarm triggered.
When conditions are not triggered, if people walk in the intrusion area, there will be no alarm triggered.
Figure 1
Figure 2
Free combination of 3 condition types: Perimeter Protection Rules, Event (Motion Detection) and Alarm Input. Once one of them are triggered, rules will be activated.
When rules are configured as conditions, each single rules will not trigger alarm.
- 96 and 160 resolution device support up to 1 combined event.
- 256 resolution device support up to 2 combined event.
- 384 and 640 resolution device support all rules.
2.4 Support Self-Learning Calibration for 160 and 256 resolution QA Heatpro series.
It can effectively filter animal false alarms with simple configuration. Choose self-learning calibration and filter level, then let people walk back and forth twice under white line area. When all white lines turn green, the calibration is done, and we suggest that you keep the process until it is good enough to meet your expectation. If further adjustment is needed, you can click the resume button or recalibrate button, and make sure someone is in the image.
Figure 3
Meanwhile support Self-Learning Calibration Record export.
Figure 4
2.5 Temperature Measurement support Smoking Filter.
Figure 5
2.6 Reflect Light Filter and Forklift Filter can be configured on each rule.
Each Expert Temperature Measurement Rule can be individually configured with Reflect Light Filter and Forklift Filter Enable.
The original outside Reflect Light Filter settings and Forklift Filter settings will act as a master switch for both normal and expert mode.
Figure 6
2.7 Thermography Model upgrade Temperature Range to -20~650°C.
HIKVISION Model
DS-2TD2528T-3/Q(C), DS-2TD2528T-7/Q(C), DS-2TD2528T-10/Q(C), DS-2TD2537T-4/Q(C), DS-2TD2537T-4Y/Q(C), DS-2TD2537T-10/Q(C), DS2TD2537T-15/Q(C)
HIKMICRO Model
HM-TD2528T-3/Q, HM-TD2528T-7/Q, HM-TD2528T-10/Q, HM-TD2537T-4/Q, HM-TD2537T-4/QY, HM-TD2537T-10/Q, HM-TD2537T-15/Q
2.8 Fire/Smoke Detection support to link Audible and Strobe Light Warning
Figure 7
2.9 Alarm output can be controlled manually and alarm status can be shown on the live view page.
Figure 8
2.10 Alarm Input support to link Audible and Strobe Light Alarm.
Figure 9
Figure 10
2.11 Support network I/O module (ADAM, ARTECO, FM2466).
Factory parks and other big scenes, need a lot of alarm inputs and alarm outputs to do the linkage. The integration network alarm module can effectively expand the number of alarms, and reduce the cost of physical wiring.
Figure 11
Figure 12
2.12 Support Custom HTTP Order Linkage.
Support to transmit alarm information to 3rd party alarm panel via HTTP Order.
Up to 10 HTTP orders could be configured.
HTTP Order, H1, H2, H3, H4, H5, H6, H7, H8, H9, H10 (Default H1)
URL: length 128
Username: length 32 (Default empty, special characters allowed)
Password: length 32 (Default empty, special characters allowed)
Figure 13
Once HTTP order function enabled, you can find the HTTP order linkage in Linkage Method page.
2.12.1 Perimeter Protection support custom HTTP linkage.
Figure 14
2.12.2 Alarm input support custom HTTP linkage.
Figure 14
2.12.3 Temperature Measurement support custom HTTP linkage
Figure 15
2.13 Perimeter Protection Audible Warning Optimization.
Default audible warning for Perimeter Protection is Siren, which is sharper and more penetrated to scare intruders away.
Besides, the AGC algorithm has been applied to control power of volume, the ensure speaker working stability for long alarm.
Figure 16
2.14 The Modbus Protocol support Main Device Mode.
MODBUS TCP supports main mode, rather than only salve mode. Cameras could sent relevant information to connected device directly.
Figure 17
2.15 Newly add OTAP for Platform Access Mode.
Figure 18
3 V5.5.98build240426 Optimized Features
3.1 384 resolution devices change default scene mode from Distant View to General, and keep good detection due to algorithm optimization.
Figure 19
3.2 Optimization of Temperature Filtering Prompts.
After Temperature filtering, the preview page displays the filtering tips, if it is forklift filter, it displays Forklift Filtered. If it is a sunlight reflection filter, it will show Reflection Filtered. If there are both forklift and reflection filters in the same rule or in the same area, it will show Forklift and Reflection Filtered.
Various combinations of filtering tips are shown in the table below.
| Filtered: Forklift |
| Filtered: Reflection |
| Filtered: Forklift and Reflection |
| Filtered: Smoking and Reflection |
| Filtered: Smoking and Forklift |
| Filtered: Smoking, Forklift, and Reflection |
Table 1
4 Key Function Distribution
5 Supported Product List
| DS-2TD2608-1/QA | DS-2TD2608-2/QA | ||
| DS-2TD1217-2/QA | DS-2TD2617-3/QA | DS-2TD2617-6/QA(C) | |
| DS-2TD1217-3/QA | DS-2TD2617-6/QA | ||
| DS-2TD1217-6/QA | DS-2TD2617-10/QA | ||
| DS-2TD1228-2/QA | DS-2TD2628-3/QA | DS-2TD2628T-3/QA | DS-2TD1228T-2/QA |
| DS-2TD1228-3/QA | DS-2TD2628-7/QA | DS-2TD2628T-7/QA | DS-2TD1228T-3/QA |
| DS-2TD1228-7/QA | DS-2TD2628-10/QA | DS-2TD2628T-10/QA | DS-2TD1228T-7/QA |
| DS-2TD2628T-10/QA(B) | DS-2TD1228T-2/QA(B) | DS-2TD1228T-3/QA(B) | DS-2TD1228T-7/QA(B) |
| DS-2TD2628-10/QA(B) | |||
| DS-2TD2138-4/Q | DS-2TD2138-35/Q | DS-2TD2138-10/QY | DS-2TD2138-25/QY |
| DS-2TD2138-7/Q | DS-2TD2138-4/QY | DS-2TD2138-13/QY | DS-2TD2138-35/QY |
| DS-2TD2138-10/Q | DS-2TD2138-7/QY | DS-2TD2138-15/QY | DS-2TD2138-4/Q(lite) |
| DS-2TD2138-4/QY(lite) | DS-2TD2138-7/Q(lite) | DS-2TD2138-7/QY(lite) | DS-2TD2138-10/Q(lite) |
| DS-2TD2138-10/QY(lite) | DS-2TD2138-15/Q(lite) | DS-2TD2138-15/QY(lite) | DS-2TD2138-25/Q(lite) |
| DS-2TD2138-25/QY(lite) | DS-2TD2138-15/QY (B) | ||
| DS-2TD2137T-4/Q | DS-2TD2137T-4/QY | DS-2TD2137T-7/QY | |
| DS-2TD2637-7/Q | DS-2TD2637-10/Q | DS-2TD2637-15/Q | DS-2TD2637-25/Q |
| DS-2TD2637-35/Q | DS-2TD2637T-7/Q | DS-2TD2637T-10/Q | DS-2TD2637T-15/Q |
| DS-2TD2637-7/QY | DS-2TD2637-10/QY | DS-2TD2637-15/QY | DS-2TD2637-25/QY |
| DS-2TD2637-35/QY | DS-2TD2637T-7/QY | DS-2TD2637T-10/QY | DS-2TD2637T-15/QY |
| DS-2TD2537T-4/Q | DS-2TD2537T-10/Q | DS-2TD2537T-15/Q | |
| DS-2TD2537T-4/Q(C) | DS-2TD2537T-4Y/Q(C) | DS-2TD2537T-10/Q(C) | DS-2TD2537T-15/Q(C) |
| HM-TD2537T-4/Q | HM-TD2537T-4/QY | HM-TD2537T-10/Q | HM-TD2537T-15/Q |
| DS-2TD2537T-4Y/Q | |||
| DS-2TD2528T-3/Q | DS-2TD2528T-7/Q | DS-2TD2528T-10/Q | DS-2TD2528T-3/Q(B) |
| DS-2TD2528T-3/Q(C) | DS-2TD2528T-7/Q(C) | DS-2TD2528T-10/Q(C) | |
| HM-TD2528T-3/Q | HM-TD2528T-7/Q | HM-TD2528T-10/Q |
6 Third-party Integration
7 Client and Platform Compatibility
Customer Impact and Recommended Action
This update refers to function/compatibility improvement and will take effect automatically after the Date of Change. We are very sorry for any inconvenience of use-habit changes caused by this action.
For any questions and request for this firmware, please contact our local technical support team.
Remarks:
- Hikvision reserves the right to change, alter or withdraw the above notification without prior notice.
- Product design and specifications are subject to change without prior notice.
- The Hikvision firmware may contain errors known as errata which may cause the product to deviate from published specifications. Current characterized errata are available on request.
- Hikvision is not liable for any typing or printing errors.
Hikvision Digital Technology CO., Ltd.
No. 555 Qianmo Road, Binjiang District, Hangzhou 310051,
China
Tel: +86-571-8807-5998
FAX: +86-571-8993-5635
Email: overseabusiness@hikvision.com
Documents / Resources
 |
HIKVISION Thermal Network Bullet and Turret Camera [pdf] User Guide QA, QY, Thermal Network Bullet and Turret Camera, Network Bullet and Turret Camera, Bullet and Turret Camera, Turret Camera, Camera |