BLM-CK Smart Key Card Power Switch
“
Specifications:
- Product Name: Smart Key-Card Power Switch
- Product Model: BLM-CK
- Networking Mode: BLE Mesh 5.0
- Mesh Forwarding: Supported
- WIFI Standard: 2.4GHz 802.11b/g/n
- Communication Distance: < 20m (affected by
environment) - Working Voltage: 100-240V~, 50/60Hz
- Rated Current: 40A (resistive load)
- Product Size: 86X86X47mm
- Product Weight: 156g
- Working Environment: 0-40°C, 10%-90%RH
(non-condensing) - Product Colors: Gold Black, Gray
- Installation Method: 86-type in-wall
installation - High-frequency Cards: 13.56MHz ISO 14443A
- Low-frequency Cards: 125kHz
- Trigger Time after Insertion: Within 1
second - Power-off Time after Removal: 38 seconds
Product Usage Instructions:
- Product Debugging:
- Indicator Light Status:
- Blue light flashing: BLE Mesh provision mode
- Blue light off: BLE Mesh provision successful
- White light flashing: WiFi connecting (no card inserted)
- White light on: WiFi connected (no card inserted)
- White light off: Card inserted
- Device Provision:
- Double-click the button within 5 minutes of power-on to enter
BLE Mesh provision mode. - Device Linkage Functions:
- With dry contact door magnet: Enables light-on without card
when door opens. - With dry contact motion sensor: Enables light-on without card
when motion is detected. - Factory Reset:
- To factory reset, follow step 2 to enter BLE Mesh Provision
mode, then long-press until the device restarts.
FAQ:
Q: How do I install the Smart Key-Card Power
Switch?
A: Follow the 86-type in-wall installation method and
connect live/neutral wires and output control wires according to
back labels.
Q: What do the indicator lights signify during
operation?
A: Blue light flashing indicates BLE Mesh provision mode,
white light flashing signifies WiFi connecting, and white light off
indicates a card is inserted.
Q: How do I reset the device to factory
settings?
A: Enter BLE Mesh Provision mode and long-press until the
device restarts for a factory reset.
“`
Smart Key-Card Power Switch
User Manual
Specifications
Product Name:
Smart Key-Card Power Switch
Product Model
BLM-CK
Networking Mode
BLE Mesh 5.0
Mesh Forwarding
Supported
WIFI Standard
2.4GHz 802.11b/g/n
Communication Distance: < 20m (affected by environment)
Working Voltage:
100-240V~, 50/60Hz
Rated Current
40A (resistive load)
Product Size
86X86X47mm
Product Weight
156g
Working Environment 0-40 10%-90%RH (non-condensing)
Product Colors
Gold Black, Gray
Installation Method
86-type in-wall installation
Wiring Method
Connect live/neutral wires and output control wires according to back labels
High-frequency Cards 13.56MHz ISO 14443A
Low-frequency Cards 125kHz
Trigger Time after Insertion Within 1 second
Power-offTimeafterRemoval 38 seconds
Product Debugging
1.Indicator Light Status
White Lights Blue Lights
White & Blue Lights
Blue light flashing: BLE Mesh provision mode Blue light off : BLE Mesh provision successful White light flashing: WiFi connecting (no card inserted) White light on: WiFi connected (no card inserted) White light off : Card inserted
2.Device Provision
Double-click the button within 5 minutes of power-on. When the blue indicator flashes, it enters BLE Mesh provision mode.
3.Device Linkage Functions
With dry contact door magnet: Enables light-on without card when door opens. The door magnet triggers temporary power supply to light fixtures. If a card is inserted, power stays on; if not, the system turns off the light and cuts power after 15 seconds. A voice device (if equipped) will broadcast a welcome message upon successful card insertion.
With dry contact motion sensor: Enables light-on without card when motion is detected. When motion is detected, power is activated, the light turns on, and a welcome message is broadcast. When no motion is detected, power is cut off.
4.Factory Reset
Follow step 2 to enter BLE Mesh Provision mode, then long-press until the device restarts for factory reset. (Factory reset requires no configuration lock; if locked, unlock via the app first.)
Wiring Instructions
Out
L(Live Wire)
N(Neutral Wire)
Out
L
N
Working Voltage:100-240V~, 50/60Hz Rated Current: 40A
FCC Caution:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules . These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: — Reorient or relocate the receiving antenna. — Increase the separation between the equipment and receiver. — Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. — Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
Documents / Resources
![]() |
Geeklink BLM-CK Smart Key Card Power Switch [pdf] User Manual BLM-CK Smart Key Card Power Switch, BLM-CK, Smart Key Card Power Switch, Key Card Power Switch, Card Power Switch, Power Switch, Switch |