FORTIN 2017 Standard Key Remote Starters and Alarm Systems Installation Guide

REV.: 20211119
Guide # 72711
THAR-FOR4 THARNESS INSTALLATION
ADDENDUM – SUGGESTED WIRING CONFIGURATION

Contents hide

1 2017 Standard Key Remote Starters and Alarm Systems

2 DESCRIPTION

3 WIRING CONNECTION

4 KEY BYPASS PROGRAMMING PROCEDURE

5 REMOTE STARTER PROGRAMMING PROCEDURE

6 REMOTE STARTER FUNCTIONALITY

7 Documents / Resources

7.1 References

2017 Standard Key Remote Starters and Alarm Systems

VEHICLE YEARS
FORD 2014-2019

Vehicle functions supported in this diagram (functional if equipped)

•	Contournement
•	T-Harness
•	Lock
•	Unlock
•	Arm
•	Disarm
•	RAP Disable
•	Trunk Release
•	Parking Lights
•	Horn
•	Tachometer
•	Hood
•	Door Status
•	Trunk Status
•	Hood Status*
•	Hand-Brake Status
•	Foot-Brake Status
•	OEM Remote monitoring
•	R.S. OEM remote Stand Alone compatible

BYPASS FIRMWARE VERSION
71. [52] FORD MINIMUM
To add the firmware version and the options, use the FLASH LINK UPDATER or FLASH LINK MOBILE tool, sold separately.

Program bypass option:

UNIT OPTION	DESCRIPTION
C1	OEM Remote status (Lock/Unlock) monitoring
D5	Lock after start

IF THE VEHICLE IS NOT EQUIPPED WITH FUNCTIONAL HOOD PIN:

Hood trigger (Output Status).

Program remote starter option:

FUNCTION	MODE	DESCRIPTION
8	2	Double 0.25 sec unlock pulse

Program remote starter option for R.S.
OEM REMOTE STAND ALONE:

FUNCTION	MODE	DESCRIPTION
38	2	Enable Press 3x Lock to remote start with the OEM remote.

Parts required (Not included)

1x	Relay (Parking lights)
3x	Diodes 1Amp
1x	THAR-FOR4

MANDATORY INSTALL

* HOOD PINHOOD STATUS: THE HOOD PIN SWITCH (INCLUDED) MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF.

SECURITY STICKER
WARNING
Included
Notice: the installation of safety elements are mandatory. The hood pin and the sticker are essential security elements and must be installed.
THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.

DESCRIPTION

Make the connection between the UNIT and the T-HARNESS

WIRING CONNECTION

KEY BYPASS PROGRAMMING PROCEDURE

2 KEY REQUIRED

Press and hold the programming button:
Connect the 4-PIN Data-link harness (Black connector).
The Blue, Red, Yellow and Blue & Red LEDs will alternatively illuminate.

Release the programming button when the LED is RED.
LEDs are ON.
If the LED is not solid RED and RED disconnect the 4-PIN Data-link harness (Black connector).Connect the required remaining harnesses.Turn the first functional key to the Ignition ON/RUN position.
Wait 3 seconds.

Turn the key to the OFF position.
Remove the first key.Turn the second functional key to the Ignition ON/RUN position.
Wait 3 seconds.Turn the key to the OFF position.
Remove the second key.

CAUTION The following step must be completed within 5 seconds.
Otherwise disconnect all connectors and go back to step 1.

Press and hold the programming button until the vehicle ignition turn ON.
Release the programming button.

The RED LED will flash rapidly 10x times.
Key bypass programmed.
The BLUE LED will flash rapidly.
CAN-Bus programmed.
If the LED is solid RED disconnect the 4 Pin connector (Data-Link) and go back to step 1.The vehicle ignition will turn OFF.

The module is now programmed.
Use the remote of the remote starter or security system to test all of the supported features to ensure proper programming.

REMOTE STARTER PROGRAMMING PROCEDURE

REFER TO THE QUICK INSTALL GUIDE INCLUDED WITH THE MODULE FOR THE REMOTE STARTER PROGRAMMING.

REMOTE STARTER FUNCTIONALITY

	All doors must be closed.
	Remote start the vehicle.
	Unlock the doors with the remote-starter remote or the OEM remote.
	Insert and Turn the key to the Ignition ON/RUN position.
	Press the brake pedal.
	The vehicle can now be put in to gear and driven.

www.fortinbypass.com
Module label

Notice: Updated Firmware and Installation Guides
Updated ﬁ rmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest ﬁ rmware and download the latest installation guide(s) prior to the installation of this product.

WARNING
The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever.
It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualiﬁ ed technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.

This guide may change without notice. See www.fortin.ca for latest version.

TECH SUPPORT
Tél: 514-255-HELP (4357)
1-877-336-7797ADDENDUM GUIDE
www.fortinbypass.com
WEB UPDATE

Documents / Resources

FORTIN 2017 Standard Key Remote Starters and Alarm Systems [pdf] Installation Guide
THAR-FOR4, 72711, 2017, 2017 Standard Key Remote Starters and Alarm Systems, Standard Key Remote Starters and Alarm Systems, Remote Starters and Alarm Systems, Starters and Alarm Systems, Alarm Systems, Systems

References

User Manual