Contents hide
1 FOR-X XQ-900DSP Premium DSP Car MP5 Player
2 INSTALLATION
3 BLUETOOTH OPERATION:
4 SPECIFICATION:
5 Documents / Resources
5.1 References
6 Related Posts

FOR-X-LOGO

FOR-X XQ-900DSP Premium DSP Car MP5 Player

FOR-X-XQ-900DSP-Premium-DSP-Car-MP5-Player-PRODUCT

FOR-X-XQ-900DSP-Premium-DSP-Car-MP5-Player-FIG-1

WARNINGS & PRECAUTIONS:
To avoid risk of serious injury or possible violation of laws, please read the following thoroughly before installation or connecting.

  •  This product is designed specifically for use with 12 volt, negative ground electrical systems only.
  • Having the wiring and installation done by expert.
  • Be sure to disconnect the cable from the negative battery terminal while installtion.
  • This apparatus shall not be exposed to dripping or splashing, and no object filled with liquids shall be placed on the apparatus.
  • Fuses shall be replaced only with the correct type and fuse value, and only when the apparatus is powered off.
  • To prevent a short circuit, never put or leave any metallic objects(such as coins or metallic tools)inside the unit.
  • Never set the volume of this product so high that you cannot hear outside traffic and emergency vehicles.

PRODUCT FEATURES:

  • Panel: Fixed
  • LCD: 2-Line VA-LCD
  • Key Light: Multi Color Bluetooth: Version 5.0 Bluetooth Music: Support DSP: Built-in
  • EQ: 28 Band,8 Preset
  • Pre-Output: SCH x 4V
  • Max Power: 4 x 60W
  • Xbass: Support
  • Xover: Support
  • 3D Surround: Support
  • 2- Way Network: Support
  • 3- Way Network: Support
  • Time Alignmnet: 0-18 ms
  • QValue: 1-20
  • Subwoofer Control: Support
  • Playback Interface: TF & USB
  • Phase: 0° -180°
  • Listening Bit Setting: Support
  • Slope: Support
  • PACTM-SWI: Support
  • Remote: Support
  • Microphone: Built-in and External
  • Radio: Preset 18FM, 12AM, RDS
  • APP Control: iOS and Android Phone USB: Charge 2A
  • Audio Format: MP3, WMA, AAC, FLAC, APE

INSTALLATION

Installation Procedures
First complete the electrical connections and then check for correctness.

Installation Opening
This unit can be installed in any dashboard having an opening as shown below:

FOR-X-XQ-900DSP-Premium-DSP-Car-MP5-Player-FIG-2

Install The Car Radio
Be sure you test all connections first, and then follow these steps to install this unit.

  1.  Make sure the ignition is turned off, and then disconnect the cable from the vehicle battery’ s negative (-) terminal.
  2.  Disconnect the wire harness and the antenna.
  3.  Remove the detachable panel and decorative enclosure frame and place on one side.
  4.  Insert the two brackets into the left and right sides of the chassis, as shown in the following figure, and separate the chassis from the sleeve.FOR-X-XQ-900DSP-Premium-DSP-Car-MP5-Player-FIG-3
  5.  Insert the installation sleeve into the center console to be installed, and bend the clip using a screwdriver. Make sure the locking rod is flush with the mounting sleeve and does not protrude.
  6.  Connect cables as shown in the wiring diagram.
  7.  Insert the car radio into the mounting sleeve.
  8.  Install decorative enclosure frame.

ACCESSORY LIST:
Please check the following accessories after opening the package:

FOR-X-XQ-900DSP-Premium-DSP-Car-MP5-Player-FIG-4

WIRING DIAGRAM: 

FOR-X-XQ-900DSP-Premium-DSP-Car-MP5-Player-FIG-5

BASIC FUNCTIONS OF PANEL KEYS: 

FOR-X-XQ-900DSP-Premium-DSP-Car-MP5-Player-FIG-6

REMOTE OPERATION: 

FOR-X-XQ-900DSP-Premium-DSP-Car-MP5-Player-FIG-7

APP OPERATION:
APP Download

  • Method 1: Please scan the QR code on the cover to download the APP and install it on your Android or Apple device.
  • Method 2: Please go to the Apple APP Store or Google Play Store and search [AUDIO DSP Control] APP, after downloading the APP, install it on your Apple&Android devices.

APP Connection 

  1.  Open the [AUDIO DSP Control] APP, click[ ■] to search for XQ-900DSP.
  2.  Click XQ-900DSP to connect, the [FOR-X-XQ-900DSP-Premium-DSP-Car-MP5-Player-FIG-9] will be red after the connect is successful.

RADIO OPERATION: Start Listening

FOR-X-XQ-900DSP-Premium-DSP-Car-MP5-Player-FIG-10

BLUETOOTH OPERATION:

Bluetooth Pairing
The first time pair mobile phone with receiver, please follow below steps:

  1. When there is no pairing, in any mode, the BT on the LCD will flash, and the pairing can be performed at this time.
  2.  Turn on the phone’ s Bluetooth to Search XQ-900DSP.
  3.  Click on the XQ-900DSP on the phone to connect. After the connection is successful, the BT will stop flashing.
  4.  When pairing is complete, the mobile phone audio will automatically transfer to the car audio system whenever a call is made or received, or when the mobile phone plays music.

Note:
For more details of bluetooth pairing, please refer to the owner’ s manual for your mobile phone.

Bluetooth Basic Operation

FOR-X-XQ-900DSP-Premium-DSP-Car-MP5-Player-FIG-11

AUX INPUT:

  1. Connect a portable audio player(commercially available). Auxiliary input jackFOR-X-XQ-900DSP-Premium-DSP-Car-MP5-Player-FIG-12
    Auxiliary input jack
    3.5mm stereo mini plug with “L” shaped connector. (commercially available).
  2. Press[FOR-X-XQ-900DSP-Premium-DSP-Car-MP5-Player-FIG-16SRC]buttons to select AUX IN.
  3.  Turn on the portable audio player and start playback.

EXTERNAL MICROPHONE: 

FOR-X-XQ-900DSP-Premium-DSP-Car-MP5-Player-FIG-13

Note:
Since the panel microphone is far from the driver’ s position, when using an external microphone, you can get better voice calls.

AUDIO SETTINGS: 

  1.  Press the knob to enter the [MENU].
  2.  Turn the knob to select [AUDIO], then press the knob.

Audio Settings List

Menu Adjustment
SW LEVEL SVOL 0 ~ 8
PRESET EQ USER/NATURAL/POP/CLASSICAL/ROCK/JAZZ/FLAT/
COUNTRA/ SUPER BASS
28BAND: 25HZ/32HZ/40HZ/S0HZ/63HZ/80HZ/100HZ/125HZ/
160HZ/200HZ/250HZ/310HZ/ 400HZ/500HZ/630HZ/800HZ/
1K/ 1.25K/2K/2.5K/ 4K/ SK/6.3K/8K/ lOK/ 12.5K/ 16K/20K
XBASS FREQ OFF/60HZ/80HZ/120HZ/160HZ/200HZ/300HZ
GAIN 0~3
SURROUND OFF/ON
BASS BASS -7 ~ +7
MIDDLE MIDDLE -7 ~ +7
TREBLE TREBLE -7 ~ +7
AUDIO RST NO-YES

Subwoofer Volume Adjustment

  1. Turn the knob to select [SW LEVEL], then press the knob.
  2. Turn the knob to adjust SVOL [-8 to +8].

Preset EQ Select

  1. Turn the knob to select [PRESET EQ ], then press the knob.
  2. Turn the knob to select [USER/NATURAL/POP/CLASSIC/ROCK/
  3. JAZZ/FLAT/COUNTRA/SUPER BASS].

User EQ Setup

  1. Turn the knob to select [PRESET EQ ], then press the knob.
  2. Turn the knob to select [USER], then press the knob.
  3. Turn the knob to select frequency for adjustment.

X-BASS Adjustment

  1. Turn the knob to select [XBASS], then press the knob.
  2. Turn the knob to adjust [0-20].

Surround Setup

  1. Turn the knob to select [SURROUND], then press the knob.
  2. Turn the knob to select [OFF/ON].

Bass Adjustment

  1. Turn the knob to select [BASS], then press the knob.
  2. Turn the knob to adjust [-7 to +7].

Middle Adjustment

  1. Turn the knob to select [MIDDLE], then press the knob.
  2. Turn the knob to select [ L7-LO to R1-R7]

AUDIO SETTINGS:

  1. Press the knob to enter the [MENU].
  2. Turn the knob to select [AUDIO], then press the knob.

Treble Adjustment

  1. Turn the knob to select [TREBLE], then press the knob.
  2. Turn the knob to select [-7 to +7].

Audio Setup Reset

  1. Turn the knob to select [AUDIO RESET], then press the knob.
  2. Turn the knob to select [NO/YES].

XOVER SETUP:

  1. Press the knob to enter the [MENU].
  2. Turn the knob to select [AUDIO], then long press the knob enter the [XOVER].

Xover List

Menu Adjustment
HPF FREQ FULL/30HZ/40HZ/50HZ/63HZ/70HZ/80HZ/
90HZ/100HZ/125HZ/160HZ/180HZ/220HZ/
250HZ/315HZ/400HZ/500HZ/630HZ/700HZ/
800HZ
FRONT SLOPE 6DB/-12DB/-18DB
LPF FREQ FULL/1K/l.6K/2.5K/3.15K/4K/5K/6.3K/ 8K/10K/12.5K
SLOPE -6DB/-12DB/-18DB
PHASE REVERSE/NORMAL
GAIN 0~8
HPF FREQ FULL/30HZ/40HZ/50HZ/63HZ/70HZ/80HZ/

90HZ/100HZ/125HZ/160HZ/180HZ/220HZ/
250HZ/315HZ/400HZ/50OHZ/630HZ/700HZ/
Net 4.2 800HZ
REAR SLOPE -6DB/-12DB/-18DB
LPF FREQ FULL/1K/l.6K/2.5K/3.15K/4K/5K/6.3K/ 8K/10K/12.5K
SLOPE -6DB/-12DB/-18DB
PHASE REVERSE/NORMAL
GAIN 0~8
LPF FREQ 30HZ/40HZ/50HZ/63HZ/70HZ/80HZ/

90HZ/100HZ/125HZ/160HZ/180HZ/220HZ/
250HZ/315HZ/400HZ/500HZ/630HZ/700HZ/
SUBWOOFER 800HZ
SLOPE -6DB/-12DB/-18DB
PHASE REVERSE/NORMAL
GAIN 0~8

XOVER SETUP: 

  1.  Press the knob to enter the [MENU].
  2.  Turn the knob to select [AUDIO], then long press the knob enter the [XOVER].

Xover List 

Menu Adjustment
 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NET 2-WAY

  

 

 

TWEETER

 HPF FREQ FULLj630HZ/700HZ/800HZ/1K/1.6K/ 2.SK/3.15K/4K/SK/6.3K/8K/10K/

12.SK/
PHASE REVERSE/NORMAL
SLOPE 6DB/12DB/18DB
GAIN LEFT 0~8
GAIN RIGHT 0 ~ 8
 

 

 

FRONT

 HPF FREQ FULlj30HZ/40HZ/50HZ/63HZ/70HZ/ 80HZ/90HZ/100HZ/125HZ/160HZ/
SLOPE -6DB/-12DB/-18DB
PHASE REVERSE/NORMAL
GAIN 0~8
 

 

 

REAR

 HPF FREQ FULLj30HZ/40HZ/S0HZ/63HZ/70HZ/ 80HZ/90HZ/100HZ/125HZ/160HZ/
SLOPE -6DB/-12DB/-18DB
PHASE REVERSE/NORMAL
GAIN 0~8
 

 

 

 

SUBWOOFER

 LPF FREQ 30HZ/40HZ/50HZ/63HZ/70HZ/

80HZ/90HZ/100HZ/125HZ/160HZ/

180HZ/220HZ/250HZ/315HZ/400HZ/ S00HZ/630HZ/700HZ/800HZ
SLOPE -6DB/-12DB/-18DB
PHASE REVERSE/NORMAL
GAIN 0~8

XOVER SETUP: 

  1.  Press the knob to enter the [MENU].
  2.  Turn the knob to select [AUDIO], then long press the knob enter the [XOVER].

Xover List

Menu Adjustment
 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NET3-WAY

  

 

TWEETER

 HPF FREQ FULL/630HZ/700HZ/800HZ/1K/l.6K/2.5K/

3.15K/4K/5K/6.3K/8K/10K/12.5K/
SLOPE -6DB/-12DB/-18DB
PHASE REVERSE/NORMAL
GAIN LEFT 0~8
GAIN RIGHT 0~8
 

 

 

 

 

 

MIDDLE

 HPF FREQ FULL/30HZ/40HZ/50HZ/63HZ/70HZ/80HZ/ 90HZ/100HZ/125HZ/160HZ/180HZ/220HZ/

250HZ/315HZ/400HZ/500HZ/630HZ/

700HZ/800HZ
SLOPE -6DB/-12DB/-18DB
LPF FREQ FULL/630HZ/700HZ/800HZ/1K/l.6K/ 2.5K/3.15K/4K/5K/6.3K/

8K/10K/12.5K/
SLOPE -6DB/-12DB/-18DB
PHASE REVERSE/NORMAL
GAIN 0~8
 

 

 

 

 

 

WOOFER

 HPF FREQ FULL/30HZ/40HZ/50HZ/63HZ/70HZ/80HZ/ 90HZ/100HZ/125HZ/160HZ/180HZ/220HZ/

250HZ/315HZ/400HZ/500HZ/630HZ/

700HZ/800HZ
SLOPE -6DB/-12DB/-18DB
LPF FREQ FULL/630HZ/700HZ/800HZ/1K/l.6K/2.5K/

3.15K/4K/5K/6.3K/8K/10K/12.5K/
SLOPE -6DB/-12DB/-18DB
PHASE REVERSE/NORMAL
GAIN 0~8
 

 

 

SUBWOOFER

 LPF FREQ 30HZ/40HZ/50HZ/63HZ/70HZ/80HZ/90HZ/

100HZ/125HZ/160HZ/180HZ/220HZ/

250HZ/315HZ/400HZ/500HZ/630HZ/

700HZ/800HZ
SLOPE -6DB/-12DB/-18DB
PHASE REVERSE/NORMAL
GAIN 0~8

XOVER SETUP:

  1. Press the knob to enter the [MENU].
  2. Turn the knob to select [AUDIO], then long press the knob enter the [XOVER].

Net 4.2 Front Setup

  1.  Turn the knob to select [NET 4.2], then press the knob.
  2.  Turn the knob to select [FRONT], then press the knob.
  3.  Turn the knob to select [HPF FREQ/HPF SLOPE/LPF FREQ/LPF SLOPE/ PHASE/ GAIN], then press the knob.

Net 4.2 Rear Setup

  1.  Turn the knob to select [NET 4.2], then press the knob.
  2.  Turn the knob to select [FRONT], then press the knob.
  3.  Turn the knob to select [HPF FREQ/HPF SLOPE/LPF FREQ/LPF SLOPE/ PHASE/ GAIN], then press the knob.

Net 4.2 Subwoofer Setup

  1. Turn the knob to select [NET 4.2], then press the knob.
  2.  Turn the knob to select [SUBWOOFER], then press the knob.
  3.  Turn the knob to select [LPF FREQ/LPF SLOPE/PHASE/GAIN], then press the knob.

Net 2-Way Tweeter Setup

  1.  Turn the knob to select [NET 2-WAY], then press the knob.
  2.  Turn the knob to select [TWEETER], then press the knob.
  3.  Turn the knob to select [HPF FREQ/GAIN LEFT/GAIN RIGHT], then press the knob.

Net 2-Way Front Setup

  1.  Turn the knob to select [NET 2-WAY], then press the knob.
  2.  Turn the knob to select [FRONT], then press the knob.
  3.  Turn the knob to select [HPF FREQ/HPF SLOPE/GAIN], then press the knob.

Net 2-Way Rear Setup

  1.  Turn the knob to select [NET 2-WAY], then press the knob.
  2.  Turn the knob to select [REAR], then press the knob.
  3.  Turn the knob to select [HPF FREQ/HPF SLOPE/GAIN], then press the knob.

Net 2-Way Subwoofer Setup

  1.  Turn the knob to select [NET 2-WAY], then press the knob.
  2.  Turn the knob to select [SUBWOOFER], then press the knob.
  3.  Turn the knob to select [LPF FREQ/LPF SLOPE/LPF PHASE/GAIN],  then press the knob.

XOVER SETUP:

  1. Press the knob to enter the [MENU].
  2. Turn the knob to select [AUDIO], then long press the knob enter the [XOVER].

Net 3-Way Tweeter Setup

  1.  Turn the knob to select [NET 3-WAY], then press the knob.
  2.  Turn the knob to select [TWEETER], then press the knob.
  3.  Turn the knob to select [HPF FREQ/HPF SLOPE/PHASE/GAIN LEFT/ GAIN RIGHT], then press the knob.

Net 3-Way Middle Setup

  1.  Turn the knob to select [NET 3-WAY], then press the knob.
  2.  Turn the knob to select [MIDDLE], then press the knob.
  3.  Turn the knob to select [HPF FREQ/HPF SLOPE/LPF FREQ/LPF SLOPE/ PHASE/GAIN ], then press the knob.

Net 3-Way Woofer Setup

  1.  Turn the knob to select [NET 3-WAY], then press the knob.
  2.  Turn the knob to select [WOOFER], then press the knob.
  3.  Turn the knob to select [HPF FREQ/HPF SLOPE/LPF FREQ/LPF SLOPE/ PHASE/GAIN ], then press the knob.

Net 3-Way Subwoofer Setup

  1.  Turn the knob to select [NET 3-WAY], then press the knob.
  2.  Turn the knob to select [SUBWOOFER], then press the knob.
  3.  Turn the knob to select [LPF FREQ/LPF SLOPE/PHASE/GAIN], then press the knob.

ANIMATION SETTINGS:

  1. Press the knob to enter the [MENU].
  2. Turn the knob to select [ANIMATION], then press the knob.
  3. Turn the knob to select [OFF/PER 15SEC/30SEC/1MIN/2MIN/4MIN].
Menu Adjustment
ANIMATION OFF/PER 15SEC/30SEC/1MIN/2MIN/4MIN

DEMO MODE SELECT:

  1. Press the knob to enter the [MENU].
  2.  Turn the knob to select [DEMO MODE], then press the knob.
  3.  Turn the knob to select [OFF/ON].
Menu Adjustment
DEMO MODE OFF/ON

DATA SETTINGS: 

  1. Press the knob to enter the [MENU].
  2. Turn the knob to select [DTA SET], then press the knob.

DTA Settings List 

Menu Adjustment
CAR TYPE SMALL/MEDIUM /LARGE
POSITION USER/FRONT L/FRONT R/CENTER
UNIT MS/CM/INCH
 

 

 

 

DISTANCE (NET 4.2)

 CHl FL 0~lS.0MS/ 0~612CM/ 0~240 INCH
CH2 FR 0~lS.0MS/ 0~612CM/ 0~240 INCH
CH3 RL 0~lS.0MS/ 0~612CM/ 0~240 INCH
CH4 RR 0~lS.0MS/ 0~612CM/ 0~240 INCH
CHS 0~lS.0MS/ 0~612CM/ 0~240 INCH
CH6 0~lS.0MS/ 0~612CM/ 0~240 INCH
CHS SUB 0~lS.0MS/ 0~612CM/ 0~240 INCH
 

 

 

DISTANCE (NET 2-WAY)

 CHl FL-TW 0~lS.0MS/ 0~612CM/ 0~240 INCH
CH2 FR-TW 0~lS.0MS/ 0~612CM/ 0~240 INCH
CH3 FL-WF 0~lS.0MS/ 0~612CM/ 0~240 INCH
CH4 FR-WF 0~lS.0MS/ 0~612CM/ 0~240 INCH
CHS RL 0~lS.0MS/ 0~612CM/ 0~240 INCH
CH6 RR 0~lS.0MS/ 0~612CM/ 0~240 INCH
CHS SUB 0~lS.0MS/ 0~612CM/ 0~240 INCH
 

 

 

 

DISTANCE (NET 3-WAY)

 CHl FL-TW 0~lS.0MS/ 0~612CM/ 0~240 INCH
CH2 FR-TW 0~lS.0MS/ 0~612CM/ 0~240 INCH
CH3 FL-MD 0~lS.0MS/ 0~612CM/ 0~240 INCH
CH4 FR-MD 0~lS.0MS/ 0~612CM/ 0~240 INCH
CHS FL-WF 0~lS.0MS/ 0~612CM/ 0~240 INCH
CH6 FR-WF 0~lS.0MS/ 0~612CM/ 0~240 INCH
CHS SUB 0~lS.0MS/ 0~612CM/ 0~240 INCH
DIA RST NO/YES

DTA ETTINGS:

  1. Press the knob to enter the [MENU].
  2. Turn the knob to select [DTA SET], then press the knob.

Car Type Settings

  1. Turn the knob to select [CAR TYPE], then press the knob.
  2. Turn the knob to select [SMALL /MEDIUM /LARGE].

Listening Position Settings

  1. Turn the knob to select [POSITION], then press the knob.
  2. Turn the knob to select [USER/FRONT R/FRONT L/CENTER].

Delay Unit Settings

  1. Turn the knob to select [UNIT], then press the knob.
  2. Turn the knob to select [MS/CM/INCH].

Distance Net 4.2 Settings

  1. Turn the knob to select [DISTANCE], then press the knob.
  2. Turn the knob to select [CH1~CH8], then press the knob.
  3. Turn the knob to select[O~18.0MS/ 0~612CM/ 0~240 INCH].

Distance Net 2-Way Settings

  1. Turn the knob to select [DISTANCE], then press the knob.
  2. Turn the knob to select [CH1~CH8], then press the knob.
  3. Turn the knob to select[0~18.0MS/ 0~612CM/0~240 INCH].

Distance Net 3-Way Settings

  1. Turn the knob to select [DISTANCE], then press the knob.
  2. Turn the knob to select [CH1~CH8], then press the knob.
  3. Turn the knob to select[O~18.0MS/ 0~612CM/ 0~240 INCH].
  4. Note: Net 4.2/Net 2-Way /Net 3-Way can be set in the “XOVER” option.

OTA Reset

  1. Turn the knob to select [DTA RST], then press the knob.
  2. Turn the knob to select [NO/YES].

TIME ALIGNMENT(DISTANCE): 

  1.  Press the knob to enter the [MENU].
  2.  Turn the knob to select [DTA SET], then press the knob.
  3.  Turn the knob to select [DISTANCE], then press the knob.
  4.  Turn the knob to select[F LEFT/F RIGHT/R LEFT/R RIGHT/SUBWOOFER] to adjust.

Determine the value for<Position> adjustment.
CD Determine the center of the currently set listening position as the reference point.

  • The adjustable speaker has five directions: front left, front right, back left, back right, and back.
  • The time for the speakers in the five directions to reach the center is the same by default.
  • Set the value for each speaker, the delay range: 0-20ms.
  • Adjust the increase or decrease of each speaker, 0.2ms each time.
    Example: When <back> is selected as the listening position:

FOR-X-XQ-900DSP-Premium-DSP-Car-MP5-Player-FIG-14

CLOCK AND DATE SETTING :

  1. Press the knob to enter the [MENU].
  2. Turn the knob to select [CLOCK], then press the knob.

Clock And Date Setting List

Menu Adjustment
CLK FORMAT 12H/24H
CLK ADJ 00:00
DATE FRMT DD-MM-YY/MM-DD-YY
DATE SET 01/01/23

Clock Format Setting

  1. Turn the knob to select [CLK FORMAT], then press the knob.
  2. Turn the knob to select [12H/24H].

Clock Adjust

  1. Turn the knob to select [CLK ADJ], then press the knob.
  2. Turn the knob to adjust.
  3. Press the knob to switch the clock/minute adjustment.

Date Format Setting

  1. Turn the knob to select [DATE FORMAT], then press the knob.
  2. Turn the knob to select [DD-MM-YY/MM-DD-YY].

Date Setting

  1. Turn the knob to select [DATE SET], then press the knob.
  2. Turn the knob to adjust.
  3. Press the knob to switch day/month/year adjustment.

TUNER SETTING:

  1.  Press the knob to enter the [MENU].
  2.  Turn the knob to select [TUNER], then press the knob.

Tunner Settings List

Menu Adjustment
TUNER MONO/STEREO NEWS/ AFFAIRS/INFO/SPORT EDUCATE/DRAMA/CULTURE SCIENCE/VARIED/POP M/ ROCK M/EASY M/LIGHT M/ CLASSICS/OTHER M/WEATHER/ FINANCE/CHILDREN/SOCIAL/ RELIGION /PHONE IN/TRAVEL/

LEISURE/JAZZ/COUNTRY/ NATION M/OLDIES/FOLK M/

DOCUMENT
DX/LOCAL
RDS OFF/ON
TA OFF/ON
AF ON/OFF
EON OFF/ON
REG OFF/ON           _J
PTY OFF/ON
REGIONAL EUROPE/USA/ASIA/RUSSIA

TUNER SETTINGS:

Stereo/Mono Select
Turn the knob to select [STEREO or MONO], then turn the knob select
[STEREO/MONO].

DX/Local Select
Turn the knob to select [LOC or DX], then turn the knob select [DX /LOCAL]. Remark: DX: Distant exchange.

RDS ON/OFF
Turn the knob to select [RDS OFF], then turn the knob select [RDS OFF, ON].

Tuner Area Select
Turn the knob to select [REGIONAL], then turn the knob select
[ASINRUSSINEUR/USA].

DISPLAY SETTINGS:

  1.  Press the knob to enter the [MENU].
  2. Turn the knob to select [DISPLAY], then press the knob.

Display Settings List 

Menu Adjustment
MODE SEL C-MODE1/C-MODE2/MODE3/
COLOR AUTO/RED/GREEN/BLUE/YELLOW/ CYAN/PURPLE/WHITE
SPECTRUM C-MODEl
ID3 TAG OFF/ON

Key Light Select 

  1.  Turn the knob to select [COLOR SEL], then press the knob.
  2.  Turn the knob to select key light color: [AUTO/RED/GREEN /BLUE/YELLOW/CYAN/PURPLE/WHITE].

Spectrum ON/OFF

  1.  Turn the knob to select [SPECTRUM], then press the knob.
  2.  Turn the knob to select [OFF/ON].

ID3 ON/OFF

  1.  Turn the knob to select [ID3 TAG], then press the knob.
  2.  Turn the knob to select [OFF/ON].

System Version

  1. Turn the knob to select [VERSION], then press the button to query the system version information.

TROUBLE SHOOTING:

  • Not working
  • Fuse blown
  • Loose panel contact
  • Not responding
  • System problem
  • No bass
  • Subwoofer setting level  is too small
  • Can’t turn on voice
  • Bluetooth is not connected Phone does not support voice
  • Not playing
  • Incorrect device format
  • Device error
  • Unsupported audio file
  • Radio reception is poor
  • Poor contact of radio antenna Poor
  • signal at location
  • Remote control is invalid
  • Remote control battery is low
  • Bluetooth call is poor
  • Microphone is too far away

Remedy

  • Replace the fuse: small lSA(Red) Take out the panel and reinstall

Reset the unit

  • Enter AUDIO to set SVOL
  • Connect Bluetooth  N.A
  • Reformat  Replacement device Replace supported audio files
  • Reconnect the radio antenna Change to other positions
  • Replace CR2025 battery
  • Speak into the microphone

SPEAKER CONNECTION:

  • Do not connect the speaker leads of the power cord to the car battery; otherwise the unit wil be seriously damaged.
  • Before connecting the speak leads of the power cord to the speakers, check the speaker wiring in your car.

FOR-X-XQ-900DSP-Premium-DSP-Car-MP5-Player-FIG-15

SPECIFICATION: 

FOR-X-XQ-900DSP-Premium-DSP-Car-MP5-Player-FIG-17

Documents / Resources

FOR-X XQ-900DSP Premium DSP Car MP5 Player [pdf] Owner's Manual
XQ-900DSP, XQ-900DSP Premium DSP Car MP5 Player, Premium DSP Car MP5 Player, DSP Car MP5 Player, Car MP5 Player, MP5 Player, Player

References

Related Posts

Leave a comment

Your email address will not be published. Required fields are marked *