FLAMMA LOGO

FS05 Multi Types Modulation Pedal
Owner’s Manual

PRECAUTIONS

Please read carefully before proceeding
Power Supply

Please connect the designated adapter to an AC outlet of the correct voltage, Please be sure the adapter supplies DC 9v 300mA, center negative. Unplug the adapter when not in use or during electrical storms

Important Safety Instructions

  1. Read these instructions
  2. Keep these instructions
  3. Heed all warnings
  4. Follow all instructions
  5. Do not use this apparatus near water
  6. Clean only with a dry cloth
  7. Do not install near any ventilation openings. Install in accordance with the manufacturer’s instructions
  8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers)that produce heat
  9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet
  10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point

FCC certification

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  • This device may not cause harmful interference
  • This device must accept any interference received, including interference that may cause undesired operation

Features

  1. High-quality stereo modulation effects
  2. 11 typical modulation effects cover a wide variety of guitar tones
  3. 7 preset slots for saving your favorite setting
  4. True bypass

FLAMMA FS05 Multi Types Modulation Pedal - Layout

  1. DC 9V: Connect to the power supply (Central negative)
  2. INPUT L (MONO):1/4″ mono unbalanced input jack (For mono connection please use this input)
  3. INPUT R: 1/4″ mono unbalanced input jack
  4. OUTPUT L (MONO):1/4″ mono unbalanced output jack (For mono connection, please use this output)
  5. OUTPUT R: 1/4″ mono unbalanced output
  6. Rate: Rotate to adjust the rate of effect
  7.  TYPE: Rotate to switch between 11 different effects
  8. DEPTH: Rotate to adjust the depth of effects
  9. CTRL 1: Parameter 1 adjustment
  10.  CTRL 2: Parameter 2 adjustment
  11. SAVE/PRESET: Press to switch between 7 different preset patches. Press and hold to store the currently selected patch setting
  12. 1-7 indicator: Indicates currently selected preset patch. Different preset patches indicated by different color
  13. Footswitch LED: Power indicator for FS05
  14. Footswitch: Toggle FS05 on/off

Instructions

  1. Switch presets
    Press the SAVE/SELECT button to switch between the 7 different reverb effects. LED indicates the currently selected effect (see manual for a full description of effects).
  2. Save presets
    When any parameter is changed that is different from the saved preset parameters, the LED indicator will blink slowly indicating the change has not yet been saved. Press and hold the SAVE button to save current settings. The LED will blink swiftly, indicating the preset has been saved successfully. Pressing the SAVE button once quickly will change to the next effect without saving.
  3. Factory reset
    To reset the pedal to factory settings, first power off the pedal. Next, press and hold the SAVE button while powering the pedal back on. The 7 LED indicators will begin to blink. Release the SAVE button LED, then wait until the indicators stop blinking to complete the factory reset. You can cancel the reset by unplugging the power supply before releasing the SAVE button.

Effect List

Number Name Effect CTRL 1 CTRL 2
1 CHORUS Clear natural stereo chorus effect with a wide frequency range MIX TONE
2 FLANGER Fat stereo flanger effect MIX FEEDBACK
3 TREMOLO Tremolo effect based on the triangle wave DUTY TONE
4 PHASE Classic phase effect MIX TONE
5 VIBRATO Pitch shifter vibrato effect MIX TONE
6 ROTARY Classic rotary effect MIX TONE
7 LIQUID The liquid-like square wave modulation effect MIX TONE
8 AUTO-WAH Auto-Wah is based on frequency sweeping MIX TONE
9 STUTTER Modulation based on square wave DUTY TONE
10 RING The classic ring modulation effect PITCH TONE
11 LOW BIT The low sample rate effect SMOOTH BIT RATE

Specifications

Input: 2*1/4″ mono audio jack (Impedance value: 4.7M ohms)
Output: 2*1/4″ mono audio jack (Impedance value: 100 ohms)
Power supply: 9V DC (Negative inside. Please ensure the polarity of power supply is correct. Voltage value should be 9V exactly.)
Current Draw: 300mA
Dimension: 69.82×121.5×50.65mm
Weight: 0.298KG
Accessories: Safety Instruction & Warranty Card, Sticker, quick guide

FLAMMA LOGO

 www.flammainnovation.com
Shenzhen Flamma Innovation Co., Ltd
Made in China

Documents / Resources

FLAMMA FS05 Multi Types Modulation Pedal [pdf] Owner's Manual
FS05 Multi Types Modulation Pedal, FS05, Multi Types Modulation Pedal

References

Leave a comment

Your email address will not be published. Required fields are marked *