fingertime 2BF6HROAM Roam Retro Design Bluetooth Headset
Product Information
Specifications
- Compliance: Part 15 of FCC Rules
- Interference Conditions: Must not cause harmful interference and must accept any received interference
- RF Exposure: Meets general RF exposure requirements for portable use
Note
- Do not use the headset at high volume for extended periods.
- Avoid using the headset in wet or humid environments.
- Charge the headset using the provided cable to avoid damage.
Product Parameters
| Bluetooth Version | Bluetooth V5.0 |
|---|---|
| Transmission Distance | 10m |
| Supported Profiles | A2DP, AVRCP, HFP, HSP |
| Frequency Range | 2.402 – 2.480GHz |
| Speaker Diameter | 40mm |
| Speaker Impedance | 32Ω |
| Battery Capacity | 500mAh |
| Charging Time | 2.5 hours |
Short press to switch the ANC Mode.
ON/ OFF. Plav/ Pause. Answer Calls/ Hana off Calls Modes Switch, activate the voice assistance
In Bluetooth mode five press to enter the Game mode no inductive delay at 0.04s.
short press for increasing volume long press for next song
short press for reducing volume long press for previous song
ANC Mode
ANC Mode: short press “” to switch the ANC Mode, voice prompts “ANC Mode”
Low Latency Mode
- Press”
” for five times to enter the low latency game mode, voice prompts “Game Mode” - Press”” for five times again to switch the music mode, voice prompts “Music Mode”
Bluetooth Mode
Bluetooth pairing: long press” ” for three seconds, voice prompts “power on” to start up the Bluetooth headphone, it will enter pairing mode automatically, voice prompts “Bluetooth Mode”, indicator light flashes with white and orange. Turn on the smart device’s Bluetooth searching function and select the device “Roam”, no password is required, after successfully pairing, a tone “Connected” will be heard, the LED indicator light flashes white slowly. Clean pairing: long press the “+” and “-” for 3s at the same time to clean the original pair of connected devices.
Button Description:
- Play/pause the music: short press” “to play or pause the music
- Last/next song: long press “+”for 2 seconds to the next song; long press” – “for 2 seconds to the previous song
- Volume control: short press “+” for increasing volume, short press” – ” for reducing volume
- Voice assistance: triple press” “to activate the voice assistance
- Answer the call: short press “ “when calls coming
- End of the call: short press ” “when calls ending
- Reject the call: long press ” “for 2 seconds when calls coming
- Power off: long press “ “for 3 seconds to turn off the headphone
LED Indicator Light Status
| Charging Status | LED is orange when charging, turns off when fully charged. |
|---|---|
| Pairing Status | LED flashes white and orange. |
| Playing Status | LED turns off. |
APPT#(Download the APP):
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF warning statement:
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
Warranty Card
| Model Number | |
|---|---|
| Purchase Date | |
| Purchase Account | |
| User Name | |
| Phone Number | |
| Purchase Shop | |
| Warranty Reason | |
| Address | |
| Order Number | |
| Buyer’s Address |
Company Information
- Shenzhen Century Digital Technology Co., Ltd.
- Address: 23/F, Building 1, Tian’an Cloud Park, No. 555, Minzhi Avenue, Longhua District, Shenzhen, Guangdong, China.
- Website: www.fingertime.cn
- Phone: 400 998 0236
Frequently Asked Questions
- Q: What should I do if I experience interference?
A: Try reorienting the antenna, increasing separation, or changing the power outlet. If issues persist, consult a professional. - Q: Can I use this device in portable settings?
A: Yes, the device is designed for portable use and meets RF exposure requirements for such conditions.
Documents / Resources
 |
fingertime 2BF6HROAM Roam Retro Design Bluetooth Headset [pdf] Instruction Manual 2BF6H-ROAM, 2BF6HROAM, 2BF6HROAM Roam Retro Design Bluetooth Headset, Roam Retro Design Bluetooth Headset, Design Bluetooth Headset, Bluetooth Headset, Headset |