FandF Wi-R1S1-D 1 Channel Wi-Fi Relay for DIN Rail Fox Module User Guide

Restore Factory Settings
If you encounter issues, restore factory settings by pressing and holding the PROG button while the controller is operating.

FAQ

Q: Can the Single Switch-D work with backlit buttons?
A: No, it is recommended to use monostable buttons with the Single Switch-D as it is not adapted for backlit buttons.

System capabilities

Communication via home Wi-Fi network;

Remote access to devices via the Polish F&F cloud;
Integration with Google and Google Home voice assistant;

Ability to work autonomously, without a Wi-Fi connection;
Advanced programmable timers based on online calendars and enhanced with astronomical functions;

Free mobile applications for Android and iOS.

Properties

Separated relay output with changeover contact, rated up to 16 A;
Possibility of connecting an external push button for local con-trol of the unit;
Receiver control via mobile app and time programmers;
Built-in RTC clock with power supply backup and local copy of settings guarantees correct operation of the programmer even in the event of lack of Wi-Fi connection;
Support for REST API and MQTT allowing the controller to inte-grate with external systems (including but not limited to Home Assistant);
Built-in antenna;
DIN rail mounting;
1S housing.

Configuration

For the initial configuration of the Fox module, it is necessary to download and run the free Fox application available for mobile devices running the system:

Android, version 8.0 or higher;
iOS, version 14 or higher.

You can download the app directly from the stores:

On the above page, you can also find detailed information on how to configure and operate the devices and the Fox mobile app.

Wiring diagram

Description of terminals

power suply – phase wire

power supply – neutral wire
local control button input

10 COM – common contact for internal relay

11 NC – normally closed contact for internal relay
12 NO – normally open contact for internal relay

It is recommended to use monostable (momentary) buttons. When using bistable buttons, at most one pushbutton can be connected to the input.
The Single Switch-D controller is not adapted to work with backlit buttons.

First launch
Once you have connected your new device to the power supply, it is advisable to carry out personalisation, i.e. linking it to your phone and user account. To do this, launch the Fox app, select the settings icon , then the Add new device command.

If you are running the application on your phone for the first time, follow the programme’s instructions to register a user account or log in to an existing account, then select Fox Wi-Fi: Search and configure wireless devices.
Personalisation of the controller takes place via a direct connection. Due to the limited range of such a con-nection, it is recommended to carry out personalisation standing directly at the controller.

Fox controllers only support 2.4 GHz Wi-Fi connections. It is not possible to connect the controller to a 5 GHz network!
Once the search process is complete, the new Fox devices will be displayed.

The Single Switch-D module will appear in the list as follows

To add a new device, you must first connect to it (press the Con-nect button) and, once it has been established (figure below), press the Configure button and continue following the instruc-tions of the application.

LED signalling

The status of the module can be directly assessed by the STATUS light located on the front of the device.
The grey color actually corresponds to the green LED and the black color to the red LED.

Restore factory settings

If you are unable to access the controller, we recommend that you restore the controller to factory settings and reconfigure it using the Fox app.

To restore the factory settings, proceed as follows

While the controller is operating, press and hold the PROG button on the front of the controller. When the button is pres-sed, the green LED will start to flash rapidly.

After about 5 seconds, the LED will turn off and you should release the PROG button.
Press the PROG button briefly, the green LED will light up aga-in.
Press and hold down the PROG button. After about 3 seconds, the previously switched on green LED control light will start to flash. After another 3 seconds, it will go out and the red LED light up.

Release the button – after a few seconds the indicator LED will turn green and the controller will restart.
After completing this procedure, the access passwords and parameters for remote access have been cleared. You can now search for your device again in the app and personalize it again.

Technical data

power supply 165÷265 V AC
control input 1

type digital
galvanic separation brak
control voltage 165÷265 V AC

control pulse current <2 mA
outputs 1
type relay

contact NO/NC
galvanic separation tak
maximum load current*

resistive load 16 A
contact voltage 250 V AC
power consumption 24 V DC

standby <1.2 W
operation (output on) <2 W
communication radio frequency 2.4 GHz

transmission Wi-Fi
radio power (IEEE 802.11n) <20 dBm
receiver sensitivity -98 dBm

* Load of a resistive nature [AC-1].
For loads of a different nature (e.g. LED lighting), the maximum load current may be significantly lower.

More information: www.fif.com.pl/en/content/24-wskazowki

terminal 2.5 mm² screw terminals (cord) 4.0 mm² screw terminals (wire)

tightening torque 0.5 Nm
working temperature 0÷45°C
humidity <90%

(no condensation of steam and aggressive gases)
dimensions 1 module (18 mm)
mounting on TH-35 rail

ingress protection IP20

Warranty

F&F products are covered by a 24-month warranty from the date of purchase. The warranty is only valid with proof of purchase. Contact your dealer or contact us directly.

CE declaration

F&F Filipowski L.P. declares that the device is in conformity with the essential requirements of Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repe-aling Directive 1999/5/EC.
The CE Declaration of Conformity, along with the references to the standards in relation to which conformity is declared, can be found on www.fif.com.pl on the product page.

Documents / Resources

FandF Wi-R1S1-D 1 Channel Wi-Fi Relay for DIN Rail Fox Module [pdf] User Guide
Wi-R1S1-D, Wi-R1S1-D 1 Channel Wi-Fi Relay for DIN Rail Fox Module, 1 Channel Wi-Fi Relay for DIN Rail Fox Module, Wi-Fi Relay for DIN Rail Fox Module, Relay for DIN Rail Fox Module, DIN Rail Fox Module, Rail Fox Module, Fox Module, Module

References

User Manual

FandF Wi-R1S1-D 1 Channel Wi-Fi Relay for DIN Rail Fox Module

Product Usage Instructions