Edge-corE RKIT 4 Post Rack Slide Rail Kit Installation Guide

Edge-corE LogoQuick Start Guide

4-Post Rack Slide-Rail Kit

RKIT-AI-2-8-SLIDE

Package Contents

Package Contents

  1. 2 x Slide-rails
  2. 4 x M4x4 screws
  3. 2 x M5x13 rack screws
  4. 8 x Rack post round hole pins
  5. Documentation—Quick Start Guide (this document)

Installation

Release the Inner Slide-Rails
  1. For each rack-rail assembly, pull the slide-rail out to its full extended position.
    Release the Inner Slide-Rails Figure 1
  2. Pull the white release tab on the inside of the inner slide-rail to remove it from the assembly.
  3. Push the lever on the middle rails to retract them back into the rail assemblies.
    Release the Inner Slide-Rails Figure 2
Attach the Inner Slide-Rails to the Switch
  1. Position each inner slide-rail on the side of the switch so that it aligns with the six mounting stand-offs.
    Attach the Inner Slide-Rails to the Switch Figure 1
  2. Place each rail onto the mounting stand-offs and then slide it back until it clicks in place and is secured.
  3. Use the M4 screws to provide additional security for the inner rail attachment to the switch. Tighten the screws to a torque of 15-20 Kgf-cm.
    Attach the Inner Slide-Rails to the Switch Figure 2
Mount the Slide-Rail Assemblies in the Rack
  1. Replace the rack hole pins on the rail assemblies for “round-hole” rack posts. Tighten the pins to a torque of 20-25 Kgf-cm. (Rack square hole pins are pre-installed.)
    Mount the Slide-Rail Assemblies in the Rack Figure 1
  2. For each rack-rail assembly, attach the rear part of the rails to the rear rack posts.
    Mount the Slide-Rail Assemblies in the Rack Figure 2
  3. Extend the front part of each rack-rail assembly until it
  4. fits into the front rack post.
  5. Secure each rail assembly to the rear post using the included M5 rack screws. Tighten the screws to a torque of 20-25 Kgf-cm.
    Mount the Slide-Rail Assemblies in the Rack Figure 3
Mount the Switch in the Slide-Rail Assemblies

Mount the Switch in the Slide-Rail Assemblies

  1. Pull the middle rails out to their full extended locked position. Ensure the inner ball bearing retainers are located at the front of the middle rails.
  2. Slide the ends of the inner slide-rails attached to the switch into the rack-rail assemblies.
  3. Push the blue release tabs on each inner slide-rail to enable the switch to slide into the rack.
  4. Secure the switch to the rack-rail assembly using the inner rail thumb screws.

Uninstall

Remove the Chassis From the Rack

Remove the Chassis From the Rack

  1. Unscrew both thumb screws on the inner rails and slide the chassis out to its full extended locked position.
  2. Pull the white release tabs on each inner rail to remove the chassis from the slide-rail assemblies.
Uninstall the Slide-Rail Assemblies
  1. Unscrew and remove the rear post M5 rack screws from each rail assembly.
    Uninstall the Slide-Rail Assemblies Figure 1
  2. At the front of each rack-rail assembly, pull the lever to release the assembly from the front rack post.
    Uninstall the Slide-Rail Assemblies Figure 2
  3. At the rear of each rack-rail assembly, push the lever to release the assembly from the rear rack post.
Remove the Inner Slide-Rails From the Switch
  1. Unscrew and remove the M4 security screws from the inner rails.
    Remove the Inner Slide-Rails From the Switch Figure 1
  2. At the rear end of each inner rail, pull up the spring latch to release the rail from the switch stand-offs.
    Remove the Inner Slide-Rails From the Switch Figure 2
  3. Slide the inner rail forward to release it from the switch.

Barcode

E072024-CS-R01
150200002779A

Documents / Resources

Edge-corE RKIT 4 Post Rack Slide Rail Kit [pdf] Installation Guide
RKIT 4 Post Rack Slide Rail Kit, RKIT, 4 Post Rack Slide Rail Kit, Rack Slide Rail Kit, Slide Rail Kit, Rail Kit

References

Leave a comment

Your email address will not be published. Required fields are marked *