DWC-XSDH05Mi Next Generation Video Analytics
Specifications
- Model: DWC-XSDH05Mi
- Default Login: admin | admin
- Includes: Star Wrench (T-20), Camera Screws and Plastic
Anchors, Mounting Template, Cable Guide Plate Screws and Plastic
Anchors, Quick Setup and Download Guides, Set of Cable Guide Plate,
Test Monitor Cables
Product Usage Instructions
Safety Precautions
Before installing and using the camera, please ensure to follow
these safety precautions:
- Ensure the camera is firmly fixed when mounted on a wall or
ceiling. - Only use the standard adapter specified in the specification
sheet to avoid fire or electrical shock. - Verify the power supply voltage is correct before connecting
the camera. - Do not connect multiple cameras to a single adapter to prevent
overheating or fire. - Securely plug the power cord into the power source to avoid
fire hazards. - Fasten the camera securely during installation to prevent
accidents. - Avoid installing in locations with extreme temperatures or high
humidity. - Keep conductive objects away from the camera to prevent
electric shock. - Avoid installation near heat sources or direct sunlight to
prevent fire hazards. - If any unusual smells or smoke are detected, disconnect the
power source immediately and contact the service center.
Installation Instructions
- Refer to the mounting template for proper placement of the
camera. - Use the provided screws and plastic anchors to secure the
camera in place. - Ensure all cables are guided properly using the cable guide
plate. - Connect the camera to the power supply following the
manufacturer’s guidelines. - Access the camera’s web browser menu using the default login
credentials (admin | admin).
FAQ
Q: Where can I find additional support materials for the
product?
A: You can download all support materials including manuals and
quick start guides from the manufacturer’s website by following
these steps:
- Go to http://www.digital-watchdog.com/resources
- Enter the part number in the ‘Search by Product’ search
bar. - Click ‘Search’ to view all supported materials related to your
product.
Quick Start Guide
DWC-XSDH05Mi
Default login information: admin | admin
When logging into the camera for the first time, you must set up a new password. You can set the new password using the DW® IP FinderTM software or directly from
the camera’s web browser menu.
Star Wrench (T-20)
Camera Screws and Plastic Anchors
Mounting Template
Cable Guide Plate Screws and Plastic Anchors
WHAT’S IN THE BOX
Waterproof Cap and Rubber Rings 1 (Black: ø0.15″ (ø4mm), White: ø0.19″ (ø5mm))
3 each
Quick Setup and Download Guides
1 set Cable Guide Plate
5 each Test Monitor Cable
1
Set of two (2)
1
1
NOTE: Download all your support materials and tools in one place 1. Go to: http://www.digital-watchdog.com/resources 2. Search your product by entering the part number in the `Search by Product’ search bar. Results for applicable part numbers will populate automatically based on the part number you enter. 3. Click `Search’. All supported materials, including manuals and quick start guide (QSGs) will appear in the results.
Attention: This document is intended to serve as a quick reference for the initial set-up. It is recommended that the user read the entire instruction manual for complete and proper installation and usage.
SAFETY AND WARNING INFORMATION
Read through this Installation Guide carefully before installing the product. Keep the Installation Guide for future reference. See the user manual for more information on the proper installation, use and care of the product. These instructions are intended to ensure that users can use the product correctly to avoid danger or property loss. Warnings: Serious injury or death may occur if any of the warnings are neglected. Cautions: Injury or equipment damage may occur if any of the cautions are neglected. WARNING 1. In the use of the product, you must be strict compliance with the electrical safety regulations of the nation and
region. When the product is mounted on a wall or ceiling, the device shall be firmly fixed. 2. Be sure to use only the standard adapter specified in the specification sheet. Using any other adapter could
cause fire, electrical shock, or damage to the product. 3. Make sure the power supply voltage is correct before using the camera. 4. Incorrectly connecting the power supply or replacing the battery may cause an explosion, fire, electric shock, or
damage to the product. 5. Do not connect multiple cameras to a single adapter. Exceeding the capacity may cause excessive heat
generation or fire. 6. Securely plug the power cord into the power source. An insecure connection may cause a fire. 7. When installing the camera, fasten it securely and firmly. A falling camera may cause personal injury. 8. Do not install in a location subject to elevated temperature, low temperature, or high humidity. Doing so may
cause fire or electric shock. 9. Do not place conductive objects (e.g. screwdrivers, coins, metal items, etc.) or containers filled with water on top
of the camera. Doing so may cause personal injury due to fire, electric shock, or falling objects. 10. Do not install in humid, dusty, or sooty locations. Doing so may cause fire or electric shock. 11. Do not install near any heat sources such as radiators, heat registers, or other products (including amplifiers)
that produce heat. 12. Keep out of direct sunlight and heat radiation sources. It may cause a fire. 13. If any unusual smells or smoke come from the unit, stop using the product at once. Immediately disconnect the
power source and contact the service center. Continued use in such a condition may cause fire or electric shock. 14. If this product does not operate normally, contact the nearest service center. Never disassemble or change this
product in any way. 15. When cleaning the product, do not spray water directly onto parts of the product. Doing so may cause fire or
electric shock. CAUTION 1. Use proper safety gear when installing and wiring the product. 2. Do not drop objects on the product or apply strong shock to it. Keep away from a location subject to excessive
vibration or magnetic interference. 3. Do not use this product near water. 4. The product shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall
be placed on the product. 5. Avoid aiming the camera directly towards extremely bright objects such as the sun, as this may damage the
image sensor. 6. The Main plug is used as a disconnect device and shall stay readily operable at any time. 7. Remove the power adapter from the outlet when then there is lightning. Neglecting to do so may cause fire or
damage to the product. 8. Do not block any ventilation openings. Install following the manufacturer’s instructions. 9. A polarized or grounding-type plug is recommended for this product. A polarized plug has two blades with one
wider than the other. A grounding-type plug has two blades and a third grounding prong. If the provided plug does not fit into your outlet, consult an electrician for replacement. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the product. 11. If any laser equipment is used near the product, make sure the surface of the sensor is not exposed to the laser beam as that may damage the sensor module. 12. If you want to move the already installed product, be sure to turn off the power and then move or reinstall it. 13. Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. 14. If cleaning is necessary, please use a clean cloth to wipe it gently. If the device will not be used for a long time, please cover the lens cap to protect the device from dirt. 15. Do not touch the camera’s lens or sensor module with fingers. If cleaning is necessary, please use a clean cloth to wipe it gently. If the device will not be used for a long time, please cover the lens cap to protect the device from dirt. 16. Use only attachments/accessories specified by the manufacturer. 17. Always use hardware (e.g. screws, anchors, bolts, locking nuts, etc.) compatible with the mounting surface and of sufficient length and construction to ensure a secure mount. 18. Use only with cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the product. 19. Unplug this product when a cart is used. Use caution when moving the cart/product combination to avoid injury from tip-over. 20. Refer all servicing to qualified service personnel. Servicing is needed when the product has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the product, the product has been exposed to rain or moisture, does not operate normally, or has been dropped.
STEP 1 PREPARING TO MOUNT THE CAMERA
1. Remove the dome. 2. Remove the protection film and gimbal sponge
between the dome and the camera module. 3. Using the mounting template sheet, mark and drill
the necessary holes in the mounting surface. · To mount the camera, use the large hole in the
center of the template and two outer screw holes. · To mount the camera using the cable guide, use the 6 screw holes on the sides of the template.
Holes for direct camera to surface installation Holes for cable plate installation
OR
Reset Button
Resetting the camera: With the camera ON, press the reset button for five (5) seconds to initiate a camerawide reset of all the settings, including network settings.
STEP 2 POWERING THE CAMERA
Pass the wires through and make all necessary connections.
Use a PoE Injector (required. Sold separately) to connect data and power to the camera using a single Ethernet cable.
OR
Use a non-PoE Switch to connect data using an Ethernet cable and use a power adapter to power the camera.
Power information Power requirements
Power consumption
Maximum cable distance Connector
DC12V, PoE, adapter not included DC: max 8.5W, 708mA PoE: max 11W, 229mA 328′ (100m) RJ45
WATERPROOF CAP INSTALLATION
The waterproof cap set comes with two rubber rings. Use the rubber ring best sized for your network cable’s diameter.
NOTE: Cables with ø4.5mm to ø5.5mm thickness should use the black rubber ring. Cables over ø5.5mm in thickness should use the white rubber ring.
NOTE: Make sure the o-ring d is in place between c and e to prevent moisture damage. In extreme environments, use an outdoor-rated electrical tape.
NOTE: Unused cables should be sealed with electric tape.
STEP 3 INSTALLING THE CAMERA – DIRECT INSTALL
1. Remove the rubber plugs from the camera’s mounting holes A and attach the camera to the mounting surface using the included anchors and screws B .
2. When mounting the camera, be sure the mounting screws are tightened all the way to the bottom panning plate. Keeping the screw not fully engaged will prevent the panning plate mechanism from working.
3. Adjust the camera’s tilt and angle by loosening the tilt screw at the base of the camera module (see STEP 4).
4. Remove the foam cover off the lens module and protective film inside the dome. Assemble the dome cover over the camera body. Align the dome and bottom case to match the position of the microphone output’s hole.
NOTE: Once the dome is attached to the base of the camera, the panning plate is locked into place and cannot be adjusted.
5. Remove the protective films from the dome. Softly wipe the dome with lens tissue or a microfiber cloth to remove any dust or smudges left from the installation process.
A
B
STEP 3 INSTALLING THE CAMERA – CABLE GUIDE PLATE INSTALL
1. Remove the rubber plugs from the camera’s mounting holes A and attach the camera to the mounting surface using the included anchors and screws B .
2. Use four (4) mounting screws to mount the cable guide plate to the mounting surface. 3. Use two (2) mounting screws to secure the camera to the cable guide plate and mounting
surface. Cable plate’s mounting holes
Camera mounting holes 4. When mounting the camera, be sure the mounting screws are tightened all the way to the
bottom panning plate. Keeping the screw not fully engaged will prevent the panning plate mechanism from working.
5. Adjust the camera’s tilt and angle by loosening the tilt screw at the base of the camera module (see STEP 4).
6. Remove the foam cover off the lens module and protective film inside the dome. Assemble the dome cover over the camera body. Align the dome and bottom case to match the position of the microphone output’s hole.
NOTE: Once the dome is attached to the base of the camera, the panning plate is locked into place and cannot be adjusted.
7. Remove the protective films from the dome. Softly wipe the dome with lens tissue or a microfiber cloth to remove any dust or smudges left from the installation process.
A B
STEP 4 ADJUSTING THE CAMERA’S ANGLE
The camera’s lens module can rotate 360°. The camera’s lens module can tilt 70°. The camera can pan 355° using the panning plate at the base of the camera.
NOTE: Once the dome is attached to the base of the camera, the panning plate is locked into place and cannot be adjusted.
STEP 5 CABLING
Connect power, network and external devices to the camera.
DI DI COM DO1 (N.O.) DO1 COM
White Yellow Sky Blue Gray + Dot
STEP 6 MANAGING THE SD CARD (OPTIONAL)
1. Locate the SD card slot at the base of the camera module. 2. Insert a class 10 SD/SDHC/SDXC card into the SD card slot by pressing
the SD card until it clicks. 3. Press the card inward until it clicks to release from the card slot, and then
pull it out from the slot.
NOTE: Maximum SD Card size supported: Up to 1TB micro SD / FAT32. When inserting the SD card into the card slot, the SD card’s contacts should be facing downward, as shown in the diagram.
STEP 7 DW® IP FINDERTM
1. Download and install the DW IP Finder from the DW website at http://www.digital-watchdog.com.
2. Open the DW IP Finder and click `Scan Devices’ to find the camera on the network.
3. A password must be set when connecting to the camera for the first time. a. Check the box next to the camera. b. Click “Bulk Password Assign” on the left. c. Enter admin/admin for the current username and password. Enter a new username and password to the right. Passwords must have at least eight (8) characters and at least four (4) combinations of uppercase and lowercase letters, numbers and special characters. Passwords cannot contain the user ID. d. Click “change” to apply all changes.
STEP 8 WEB VIEWER
*
The GUI display may differ depending on the camera model.
1. Find the camera using the DW IP Finder. 2. Double-click on the camera’s view in the results table. 3. Press the `View Camera Website’. 4. Enter the camera’s username and password you set up in the DW IP
Finder. If you did not set up a new username and password, a message will direct you to set up a new password for the camera to view the video.
NOTE: Please see the full product manual for web viewer setup, functions and camera settings options.
NOTE: This products is covered by one or more claims of the HEVC Patents
listed at patentlist.accessadvance.com.
Tel: +1 866-446-3595 / 813-888-9555 Technical Support Hours: 9:00AM 8:00PM EST, Monday through Friday
digital-watchdog.com
Rev: 02/25
Copyright © Digital Watchdog. All rights reserved. Specifications and pricing are subject to change without notice.
Documents / Resources
 |
DIGITAL WATCHDOG DWC-XSDH05Mi Next Generation Video Analytics [pdf] User Guide DWC-XSDH05Mi Next Generation Video Analytics, DWC-XSDH05Mi, Next Generation Video Analytics, Generation Video Analytics, Video Analytics |