Digital-Logic-LOGO

Digital Logic uFR Zero Online Tester

Digital-Logic-uFR-Zero-Online-Tester-PRO

Introduction

The uFR Zero Online Tester software is designed to evaluate the WiFi and NFC functionalities of the uFR Zero Online device. It provides options to enable or disable WiFi and the NFC field, as well as to check the NFC card’s UID through polling over USB and WiFi.

Digital-Logic-uFR-Zero-Online-Tester- (1)

Connecting the Device

To begin using the uFR Zero Online Tester, first connect the uFR Zero Online device to your computer via USB. Once the connection is established, click the “Connect to uFR” button in the software interface. This will initiate the communication between the software and the device, allowing you to proceed with testing its WiFi and NFC capabilities.Digital-Logic-uFR-Zero-Online-Tester- (2)

If the device successfully connects, a confirmation message will appear, as shown in the image above. If you encounter any errors during the connection process, please refer to the Troubleshoot section for guidance on resolving common issues.

Testing NFC and WiFi Capabilities

To test the NFC and WiFi functions, place an NFC card on the reader. The card’s UID should be displayed in both the “Card UID over USB” and “Card UID over WiFi” sections of the software. This confirms that the device is correctly reading the NFC card through both communication methods.Digital-Logic-uFR-Zero-Online-Tester- (3)

WiFi or NFC

Turning Off WiFi or NFC
If you need to turn off WiFi or NFC, simply click the “Turn OFF WiFi” or “Turn OFF NFCi” button in the software. A confirmation message will appear, indicating that the WiFi or NFC has been successfully disabled.Digital-Logic-uFR-Zero-Online-Tester- (4)

Turning On WiFi or NFC
If you need to turn on WiFi or NFC, simply click the “Turn ON WiFi” or “Turn ON NFC” button in the software. A confirmation message will appear, indicating that the WiFi or NFC has been successfully enabled.Digital-Logic-uFR-Zero-Online-Tester- (5)

Troubleshooting

If you encounter a WiFi error during device connection, as shown in the image below, try the following steps:

  1. Open the WiFi options in Windows and search for a device named “ONxxxxxx.”
  2. Attempt to connect to this device. It should appear as a WiFi network.

This process will help establish a proper connection to the uFR Zero Online device via WiFi.Digital-Logic-uFR-Zero-Online-Tester- (6)

Revision history

Digital-Logic-uFR-Zero-Online-Tester- (7)

FCC Warnings

Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this device.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. this device must accept any interference received, including interference that may cause undesired operation.

Note: This device has been tested and found to comply with the limits for a Class B digital device, according to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy and, if not installed and used following the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the device and receiver.
  • Connect the device to an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device should be installed and operated with a minimum distance of 20cm between the radiator and your body.

Address: Nemanjina 57a, 12000 Pozarevac, Serbia
Tel: +38112541022
VAT: 111385444
Reg. 21473642
e-mail: office@d-logic.com
www.d-logic.com

Documents / Resources

Digital Logic uFR Zero Online Tester [pdf] User Manual
DLZERO 2BLE2-DLZERO, 2BLE2DLZERO, dlzero, uFR Zero Online Tester, Zero Online Tester, Online Tester, Tester

References

Leave a comment

Your email address will not be published. Required fields are marked *