DAYTECH BT007 Call Button

Product Information

Specifications

• Product Name: Call Button
• Product Model: BT007
• Operating Temperature: -30°C to +70°C
• Transmitter Battery: CR2450 / 600mAH Lithium Manganese Dioxide Button Battery
• Standby Time: 3 years

Product Usage Instructions

Installation

1. Read the instructions carefully before installation.
2. [Specific Installation Steps]
3. [Additional Installation Guidelines]

Operation

1. [Step-by-step Operating Instructions]
2. [Tips for Optimal Performance]

Maintenance

To maintain compliance with FCC’s RF Exposure guidelines, ensure a minimum distance of 20cm between the device and your body. Use only the supplied antenna.

Troubleshooting

If you encounter any issues during operation, refer to the troubleshooting section in the manual or contact customer support for assistance.

FAQ

Q: What should I do if the device does not respond when pressing the call button?

A: Check the battery level in the transmitter and replace it if necessary. Ensure the receiver is within range and operational.

Q: How can I extend the standby time of the device?

A: To maximize standby time, use high-quality batteries and avoid exposing the device to extreme temperatures.

Product Overview

• The transmitter and receiver are used together, with no wiring, and no installation is simple and flexible, this product is mainly suitable for orchard farm alarms, family residences, companies, hospitals, hotels, factories, and other environments.

Product Feature

• Simple operation, press the button to work.
• Easy to install, can be screwed on the wall can be double-sided tape attached to the smooth wall in the desired position.
• The remote control distance in an open and barrier-free environment can reach 150-300 meters: the remote control signal is stable and does not interfere with each other.
• There are indicators when working.

Product Drawing

Operating Manual

1. Open the package and take out the product.
2. Power the receiver into the code-matching learning mode.
3. Short press the switch button to send a signal to the receiver and light the blue indicator.

Replace Battery

1. Insert a small screwdriver into the bottom notch of the launcher and open the cover.
2. Take out the old battery, dispose of the removed battery properly, install a new battery into the battery groove, and pay attention to the positive and negative terminals.
3. Align the launcher cover with the base and snap the buckle to close the top cover.

Technical Specification

operating temperature	-30℃ to +70℃
working frequency	433.92MHz±280KHz
Transmitter battery	CR2450 / 600mAH  Lithium Manganese Dioxide Button Battery.
Standby time	3 year

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference

1. this device may not cause harmful interference,
2. this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, according to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used per the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with a minimum distance between 20cm of the radiator and your body:
Use only the supplied antenna.

Documents / Resources

DAYTECH BT007 Call Button [pdf] Instruction Manual 2AWYQ-BT007, 2AWYQBT007, BT007 Call Button, BT007, Call Button, Button

References

• User Manual