DA-LITE-logo

DA-LITE C Controlled Screen Return

DA-LITE-C-Controlled-Screen-Return-product

Specifications

  • Model: C With CSR (Controlled Screen Return)
  • Mounting Options: Wall, Ceiling
  • Adjustment Knob for Retraction Speed
  • CSR Unit for Controlled Screen Return

Product Usage Instructions

Installation
Screen may be mounted on a wall, suspended from ceiling, or extension brackets. Ensure proper mounting to maintain screen stability.

Wall Mounting

  1. Select appropriate fasteners for the wall.
  2. Insert fasteners through openings in end caps without over tightening.
  3. Securely attach the screen to a solid surface, ensuring it is level.
  4. Verify the screen is mounted level.

Ceiling Mounting

  1. Install heavy screw hooks into wood joists or use suitable alternatives for different ceilings.
  2. Hang the screen ensuring the back of the case is perpendicular to the floor.
  3. Ensure the screen is mounted level and perpendicular to the mounting surface.

FAQ:
Q: What should I do if the screen does not retract at all?
A: If the screen does not retract, check if the CSR unit is functioning correctly. If needed, contact Da-Lite for further assistance.

INSTRUCTION BOOK FOR
Model C With CSR (Controlled Screen Return)

Installation

Screen may be mounted on a wall, suspended from ceiling or extension brackets. Wall screens must be mounted level and with the case-back parallel to the wall.

Wall Mounting

  1. Select fasteners of proper type for wall or ceiling involved.
  2. Insert fasteners through proper openings provided in back side of end caps. See figure 1.
    NOTE: DO NOT over tighten fasteners or damage may occur.
  3. Attach screen securely to studding or other solid surface – never to plaster only.
  4. MAKE SURE SCREEN IS MOUNTED LEVEL.

DA-LITE-C-Controlled-Screen-Return- (2)

Ceiling Mounting

  1. Heavy screw hooks may be installed into wood joists. Other types of hooks or chain may be used for other ceilings or for stage installations.
  2. Insert hooks or chain through proper openings provided in sides of end caps. Screen must hang so that flat back of case is perpendicular to floor.
    NOTE: DO NOT hang from the end caps at an angle. See Figure
  3. Must be perpendicular to the mounting See Figure 4.
  4. MAKE SURE SCREEN IS MOUNTED LEVEL.

DA-LITE-C-Controlled-Screen-Return- (3)

Operating Instructions

To Lower Picture Surface
Pull screen down all the way. HESITATE – then allow screen to retract VERY SLOWLY until it locks in place.

To Raise Picture Surface

  • Pull down on the pull bail, then release quickly. The screen will retract gently into the case.
  • To Adjust Retraction Speed (Screens 96″ Wide and Under) Use a large flat screwdriver to turn the adjustment knob on the right end of the screen (Figure 5). To increase the travel speed turn counterclockwise. To decrease the travel speed turn clockwise. Adjustments
  • should be made in half turn increments and travel speed checked before adjusting further.
  • NOTE: This feature is not available on some large screen sizes. Call the factory for adjustment instructions.
  • Large picture surfaces are heavy and will start up too slowly to prevent the locking dog from catching unless help is provided, so keep picture surface moving briskly.
  • Should the locking dog catch, pull the picture surface down about 4 inches and start the surface up rapidly.

DA-LITE-C-Controlled-Screen-Return- (4)

Troubleshooting

DA-LITE-C-Controlled-Screen-Return- (5)

LIMITED ONE YEAR WARRANTY ON DA-LITE PRESENTATION PRODUCTS

Milestone AV Technologies LLC warrants certain Da-Lite branded products to the original purchaser only, to be free from defects in materials and workmanship for a period of one (1) year from the date of purchase by the original purchaser; provided they are properly operated according to Da-Lite’s instructions and are not damaged due to improper handling or treatment after shipment from the factory.
This warranty does not apply to equipment showing evidence of misuse, abuse or accidental damage, or which has been tampered with or repaired by a person other than authorized Da-Lite personnel.
Da-Lite’s sole obligation under this warranty shall be to repair or to replace (at Da-Lite’s option) the defective part of the merchandise. Returns for service should be made to your Da-Lite dealer. If it is necessary for the dealer to return the screen or part to Da-Lite, transportation expenses to and from Da-Lite are payable by the purchaser and Da-Lite is not responsible for damage in shipment.
To protect yourself against damage or loss in transit, insure the product and prepay all transportation expenses.

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES AS TO FITNESS FOR USE AND MERCHANTABILITY. Any implied warranties of fitness for use, or merchantability, that may be mandated by statute or rule of law are limited to the one (1) year warranty period. This warranty gives you specific legal rights, and you may also have other rights, which vary from state-to-state. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, NO LIABILITY IS ASSUMED FOR EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN OPERATION OF EQUIPMENT, OR FOR INCIDENTAL, DIRECT, OR CONSEQUENTIAL DAMAGES OF ANY NATURE.
In the event that there is a defect in materials or workmanship of a Da-Lite product, you may contact our Customer Care Specialists at 3100 North Detroit Street, Warsaw, IN 46582, 574-267-8101, 800-622-3737.
IMPORTANT: THIS WARRANTY SHALL NOT BE VALID AND DA-LITE BRANDED PRODUCTS SHALL NOT BE BOUND BY THIS WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH THE DA-LITE WRITTEN INSTRUCTIONS.
Keep your sales receipt to prove the date of purchase and your original ownership.

Model C with CSR

The Model C with CSR is a manual wall- or ceiling-mounted screen for larger rooms with a controlled screen return that ensures a quiet, controlled return to the case. Screens with CSR must be fully extended.

DA-LITE-C-Controlled-Screen-Return- (6)

Features

  • Standard white powder-coated finish; available in black upon request
  • Quiet, controlled screen return to case
  • Includes pull cord
  • Optional floating mount brackets for wall or ceiling stud installation that can be aligned left or right.

Optional Accessories

  • Ceiling Trim Kit for Model C and Model C with CSR
  • Floating Mounting Bracket for Model C and Model C with CSR
  • Mounting and Extension Brackets
  • Pull Rod
  • Tilt Lock

16:9 HDTV Format DA-LITE-C-Controlled-Screen-Return- (7)

16:10 Wide Format DA-LITE-C-Controlled-Screen-Return- (8)

4:3 Video Format DA-LITE-C-Controlled-Screen-Return- (9)

Available with the Following Screen Surfaces

DA-LITE-C-Controlled-Screen-Return- (10)

Product images

DA-LITE-C-Controlled-Screen-Return- (11)

A BRAND OF MILESTONE AV TECHNOLOGIES | www.milestone.com
P 800.622.3737 / 574.267.8101 F 877.325.4832 / 574.267.7804
E info@da-lite.com
In British Columbia, Milestone AV Technologies ULC carries on business as MAVT Milestone AV Technologies ULC.
©2018 Milestone AV Technologies. DL–0501 (Rev. 4) 04.18.
Da-Lite is a registered trademarks of Milestone AV Technologies. All other brand names or marks are used for identification purposes and are trademarks of their respective owners. All patents are protected under existing designations. Other patents pending.

Model C with CSR
Spring Roller Type Screen with Controlled Screen Return
SUGGESTED SPECIFICATIONS: projection screen(s),
(H) x (W), wall or ceiling mounting type. To have black masking borders standard on flame retardant and mildew resistant fiberglass fabric, mounted on a ball bearing rigid steel spring roller. To be equipped with Controlled Screen Return (CSR) to control the return speed of the screen surface back into the case. Fabric to be permanently attached to roller. To have powder coated white 21-gauge steel case with flat back design. To have heavy-duty end caps concealing roller ends with steel inner plates to support roller and provide added case strength. End caps shall form sturdy brackets for wall or ceiling installations. Bottom of screen shall be formed into pocket holding tubular metal slat. A 6′ pull cord with plastic knob is included. A steel pull bail shall be attached to the slat. Heavy-duty plastic caps shall protect the ends of the slat. Bumper stops shall be built into the case to prevent slat wedging inside case.

HDTV (16:9) Format Dimensions

Viewing Area Sizes (H x W) Nominal Diagonal A – Overall Length of Case B – Between Hanger Eyes Approx. Ship. Wt.
In. Cm In. Cm In. Cm In. Cm Lbs. Kg
45″ x 80″ 114 x 203 92″ 234 875⁄16″ 222 8513⁄16″ 218 47 21.3
52″ x 92″ 132 x 234 106″ 269 995⁄16″ 252 9713⁄16″ 248 53 24.0
54″ x 96″ 137 x 244 110″ 279 1035⁄16″ 262 10113⁄16″ 258 56 25.4
58″ x 104″ 147 x 264 119″ 302 1115⁄16″ 283 10913⁄16″ 279 61 27.7
65″ x 116″ 165 x 295 133″ 338 1235⁄16″ 313 12113⁄16″ 309 67 30.4
78″ x 139″ 198 x 353 159″ 404 1475⁄16″ 374 14513⁄16″ 370 73 33.1

(16:10) Wide Format Dimensions

Viewing Area Sizes (H x W) Nominal Diagonal A – Overall Length of Case B – Between Hanger Eyes Approx. Ship. Wt.
H x W Cm In. Cm In. Cm In. Cm Lbs. Kg
50″ x 80″ 127 x 203 94″ 239 875⁄16″ 222 8513⁄16″ 218 47 21.3
57½” x 92″ 146 x 234 109″ 277 995⁄16″ 252 9713⁄16″ 248 57 25.9
60″ x 96″ 152 x 244 113″ 287 1035⁄16 262 10113⁄16″ 258 59 26.8
65″ x 104″ 165 x 264 123″ 312 1115⁄16″ 283 10913⁄16″ 279 61 27.7
69″ x 110″ 175 x 279 130″ 330 1175⁄16″ 298 11513⁄16″ 294 65 29.5
72½” x 116″ 184 x 295 137″ 348 1235⁄16″ 313 12113⁄16″ 309 66 29.9
87″ x 139″ 221 x 353 164″ 417 1475⁄16″ 374 14513⁄16″ 370 83 37.6

Video (NTSC 4:3) Format Dimensions

Viewing Area Sizes (H x W) Nominal Diagonal A – Overall Length of Case B – Between Hanger Eyes Approx. Ship. Wt.
In. Cm In. Cm In. Cm In. Cm Lbs. Kg
43″ x 57″ 109 x 145 72″ 183 631⁄8″ 160 615⁄8″ 157 23 10.4
50″ x 67″ 127 x 170 84″ 213 731⁄8″ 186 715⁄8″ 182 26 11.8
60″ x 80″ 152 x 203 100″ 254 875⁄16″ 222 8513⁄16″ 218 49 22.2
69″ x 92″ 175 x 234 120″ 305 995⁄16″ 252 9713⁄16″ 248 55 24.9
87″ x 116″ 221 x 295 150″ 381 1235⁄16″ 313 12113⁄16″ 309 70 31.8
105″ x 140″ 267 x 356 180″ 457 1475⁄16″ 374 14513⁄16″ 368 86 39.0
120″ x 160″ 305 x 406 200″ 508 1675⁄16″ 425 16513⁄16″ 421 96 43.5

Square Format Dimensions

Sizes (H x W) A – Overall Length of Case B – Between Hanger Eyes Approx. Ship. Wt.
In. Cm In. Cm In. Cm Lbs. Kg
60″ x 60″ 152 x 152 631⁄8″ 160 615⁄8″ 157 24 10.9
70″ x 70″ 178 x 178 731⁄8″ 186 715⁄8″ 182 27 12.2
72″ x 72″ 183 x 183 751⁄8″ 191 735⁄8″ 187 31 14.1
84″ x 84″ 213 x 213 875⁄16″ 222 8513⁄16″ 218 51 23.1
8′ x 8′ 244 x 244 995⁄16″ 252 9713⁄16″ 248 57 25.9
9′ x 9′ 274 x 274 1115⁄16″ 283 10913⁄16″ 279 64 29.0
10′ x 10′ 305 x 305 1235⁄16″ 313 12113⁄16″ 309 70 31.8
12′ x 12′ 366 x 366 1475⁄16″ 374 14513⁄16″ 370 90 40.8

PRODUCT NOTES

  • Matte White: Horizontal seam required when both dimensions exceed 10′.
  • High Contrast Matte White and Video Spectra 1.5: Available in sizes where both dimensions do not exceed 8′.
  • Overall case length dimensions +/- ¼” (6 mm).
  • Detail dimensional drawings and installation instructions available upon request.
  • Specifications subject to change without notice.
  • Custom formats and sizes available upon request
  • Optional Accessories: to provide clearance: Furnish heavy extension wall brackets to mount screen 6″ from wall. To provide for keystone elimination: Furnish heavy extension wall brackets to mount screen 10″ or 14″ from wall or furnish heavy adjustable extension wall brackets to mount screen 10″, 14″, 15¾”, 18¼”, 20″ or 24″ from wall.
  • NOTE: Brackets also are used for mounting screen across a corner.

WHEN ORDERING, MARK APPROPRIATE SELECTIONS

  1. Select size from charts on the other side.
  2. Select viewing surface (All Da-Lite surfaces are GREENGUARD GOLD Certified.): Matte White Video Spectra 1.5
    High Contrast Matte White
  3.  Optional accessories:
  • Extra Drop available to lower picture area more than normal. Specify total drop at top _____ (black or white) or at bottom _____ (black or white). 13′ maximum total surface height including picture area (12′ maximum on 200″ Diag.)
  • No. 6 Wall Bracket – extends 6″ non-adjustable extension brackets (140# maximum per pair) (black or white).
  • No. 11 Wall Bracket – 10″ or 14″ non-adjustable extension brackets (75# maximum per pair) (black or white).
  • No. 23 Adjustable Wall Bracket –extends 10″, 14″, 15¾”, 18¼”, 20″ or 24″
  • (75# per pair maximum) (black or white).
  • Pull Rod – 38″.
  • No borders (Black masking borders standard)
  • Floating Mounting Bracket (black or white).
  • Recommended for drywall installations.
  • Ceiling Trim Kit.
  • Black case (white standard).

PRODUCT VIEW

DA-LITE-C-Controlled-Screen-Return- (12)

ACCESSORIES DA-LITE-C-Controlled-Screen-Return- (13)

Extension Wall Brackets DA-LITE-C-Controlled-Screen-Return- (1)

Pull Rod – 38″
Zinc plated rod with black plastic handle grip allows easy access to screen when mounted out of reach. Also can be used as a pointer.

A BRAND OF MILESTONE AV TECHNOLOGIES
www.milestone.com
P 800.622.3737 / 574.267.8101
F 877.325.4832 / 574.267.7804
E info@da-lite.com
In British Columbia, Milestone AV Technologies ULC carries on business as MAVT Milestone AV Technologies ULC.
©2017 Milestone AV Technologies. DL–0227 (Rev. 6) 12.17.
Da-Lite is a registered trademarks of Milestone AV Technologies. All other brand names or marks are used for identification purposes and are trademarks of their respective owners. All patents are protected under existing designations. Other patents pending.

  • Project Name:
  • Architect:
  • Contractor:
  • Phone:
  • Reseller:
  • Phone:

Documents / Resources

DA-LITE C Controlled Screen Return [pdf] Owner's Manual
92688, C Controlled Screen Return, Controlled Screen Return, Screen Return, Return

References

Leave a comment

Your email address will not be published. Required fields are marked *