ZF Plus Sound Jacket for Scroll Compressors
“
Specifications
- Product Name: Copeland Scroll Compressor Sound Jacket
- Compatibility: Suitable for all Copeland scroll
compressors - Usage: Indoor
- Material: Acoustic material with Velcro system
Product Usage Instructions
1. Sound Jacket Installation
- Install the compressor in the designated location.
- Prepare cuts in the pressed inserts of the jacket to fit around
the compressor without damaging the acoustic material. - Position the jacket around the compressor body, including the
electrical terminal box, ensuring a good fit. - Secure the jacket in place using the Velcro system.
2. General Installation Recommendations
- Ensure the bottom of the jacket touches the floor.
- Avoid gaps between the jacket and connecting pipework.
- Install electrical cables beside a foot recess in the
jacket. - Avoid direct contact between the jacket and compressor.
- Do not cut out sound insulation material for the electrical
terminal box; wrap the jacket around the compressor body.
Frequently Asked Questions (FAQ)
Q: Can the sound jacket be used outdoors?
A: No, the sound jacket is designed for indoor use only.
Q: Is the sound jacket compatible with all compressor
brands?
A: The sound jacket is suitable for all Copeland scroll
compressors.
Q: How should I clean the sound jacket?
A: Use a damp cloth with mild soap to gently clean the surface
of the sound jacket. Avoid harsh chemicals or abrasive
materials.
“`
TI_Scroll_Sound_Jacket_EN_Rev00
TECHNICAL INFORMATION
Copeland scroll compressors
Sound jacket Installation instructions
1 Introduction
The sound jacket developed by Copeland is designed for indoor use and is suitable for all Copeland scroll compressors. It has no impact on the performance of the compressor.
The design consists of a top cap cover and compressor shell cover with an adjustable Velcro system.
It has good characteristics in case of fire and is resistant to: mineral and polyolester oil; refrigerants R22/R404A/R134a/R410A/R407C; temperature up to 150 °C; water…
The jacket is best fitted to the compressor and is attractive in appearance. It perfectly fits the shape of the compressor including the electrical box for better sound attenuation.
There are pressed inserts for pipework connections. ZF* compressors have additional pressed inserts for liquid injection and/or vapour injection with use of a DTC valve/capillary tube and inserts for the DTC sensing bulb and cap, located in the top cap.
The correct fitting of the jacket is important for good sound insulation: A sound jacket must properly seal the compressor (around connecting pipework and feet). Contact between the compressor and the blanket should be avoided.
2 Sound jacket installation
1) Install the compressor.
2) Prepare cuts in the pressed inserts before putting the jacket around the compressor. Only cut in the pressed area, being careful not to damage the acoustic material.
3) Position the jacket around the compressor including the electrical terminal box. First, the compressor body, then the top cap. Adjust the pre-cutouts where necessary for a good fit.
4) Close with the Velcro.
Application Engineering Europe
1/2
General installation recommendations
The bottom of the jacket should touch the floor as much as possible. There should be no gap between the jacket and the connecting pipework. Electrical cables should be installed beside a foot, where there is a recess off in the jacket. Contact between jacket and compressor should be avoided. Do not cut out the sound insulation material to accept the electrical terminal box. The jacket should wrap around
the compressor body including the electrical terminal box.
DISCLAIMER: The Copeland logo is a trademark and service mark of Copeland LP or one of its affiliates. Copeland Europe GmbH shall not be liable for errors in the stated capacities, dimensions, etc., as well as typographic errors. Products, specifications, assumptions, designs and technical data contained in this document are subject to modification by us without prior notice. Illustrations are not binding. ©2025 Copeland LP. All rights reserved.
Application Engineering Europe
2/2
Documents / Resources
 |
COPELAND ZF Plus Sound Jacket for Scroll Compressors [pdf] Instruction Manual ZF Plus Sound Jacket for Scroll Compressors, ZF Plus, Sound Jacket for Scroll Compressors, Scroll Compressors |