FC-001 Remote Control
“
Specifications
- Model: FC-001 CT-001
- Remote Control Instructions
Product Usage Instructions
Installation Preparation
- Remote Control Installation
There are two methods for remote control holder
installation:
- Method 1:
- Drill a 6 mm diameter hole in the wall to a depth of about 35
mm. - Remove the double-sided adhesive tape on the back of the
holder. - Install an anchor into the hole, stick the holder to the wall
and secure with screws and then stick the patch with tape.
- Drill a 6 mm diameter hole in the wall to a depth of about 35
- Method 2:
- Clean and dry the pre-installation area of the holder.
- Remove the double-sided adhesive tape on the back of the
holder. - Stick the holder to the wall vertically and then stick the
patch with tape.
To install batteries into the remote control, follow these
steps:
- Insert batteries into the remote control.
- Put the remote control into the holder.
Usage Instructions
- Remote Control Illustration
- Drying/Dryer Temperature Adjustment
- Water Volume Adjustment
- Nozzle Position Adjustment
- Energy Saving Mode
The remote control features various functions including
Rear/Front washing, Drying/Dryer temperature adjustment, Water
volume adjustment, Nozzle position adjustment, Energy saving mode,
Water temperature adjustment, Seat temperature adjustment, Night
light, Full flush/Half flush, Auto lid open/close, Auto
deodorization, User code setting, and other operations.
The dryer temperature can be adjusted by pressing the
corresponding buttons on the remote control. The indicator light
will show the current air temperature level. The dryer will stop
automatically after one cycle or when not in use. Adjust the
temperature between levels 0-5 using the buttons.
The water volume can be adjusted using the remote control.
Follow the instructions provided on the remote to increase or
decrease water volume as needed.
The position of the nozzle can be adjusted using the remote
control. Use the designated buttons to move the nozzle forward or
backward as required.
To enter energy-saving mode, long-press the corresponding button
on the remote control. Seat temperature will be set to Level 1 for
energy-saving purposes. To exit energy-saving mode, long-press the
button again.
FAQ
Q: Can I use the product in damp places like a shower
room?
A: No, it is not recommended to install and use the product in
damp places such as a shower room.
Q: How can I adjust the seat temperature?
A: The seat temperature can be adjusted using the remote
control. Follow the instructions provided to set the desired
temperature level.
“`
Model: FC-001 CT-001
Remote Control Instructions
Thank you for choosing our products. Please read the instructions carefully before installation and keep it available for future maintenance or reference.
Get free technical support for the lifetime of your product. Email: service@canesthome.com Phone: 1-702-824-3195
Content
Installation preparation
01. Remote control installation
01
02. Battery installation
01
Usage instruction
01. Remote control illustration
02
02. Rear/Front washing
03
03. Drying/Dryer temperature
04
04. Water volume adjustment
04
05. Nozzle position adjustment
04
06. Energy saving
04
07. Water temperature adjustment
05
08. Seat temperature adjustment
05
09. Night light
05
10. Full flush/Half flush
05
11. Auto lid open/close
06
12. Auto deodorization
06
13. User code
06
14. Other operations
07
Installation Preparation
Remote control installation
Remote control holder installation 1 1. Drill a 6 mm diameter hole in the wall to a depth of about 35 mm. 2. Remove the double-sided adhesive tape on the back of the holder. 3. Install an anchor into the hole, stick the holder to the wall and secure with screws and then
stick the patch with tape.
Double-side tape
Patch
Remote control holder installation 2
1. Clean and dry the pre-installation area of the holder. 2. Remove the double-sided adhesive tape on the back of the holder. 3. Stick the holder to the wall vertically and then stick the patch with tape.
Installation area
Double-side tape
Battery installation: 1. Insert batteries into the remote control. 2. Put the remote control to the holder.
Patch
Battery cover
Notice: 1. Please ensure the remote control is within reach when a person on the seat. 2. Do not install and use the product in damp places such as a shower room. 3. Do not place the product in a place where it is easily exposed to water.
01
Installation Preparation Remote control illustration
Drying/ Dryer temperature
Rear washing/ oscillating washing
Front washing/ oscillating washing
Nozzle moving forward
Water reducing
Nozzle moving backward Water
temperature Deodorizer Full flush
Open/ Close the lid
Indicator light
Water increasing Stop/Energy saving Night light Seat temperature Half flush Open/Close the seat
02
Usage Instruction
Notice : · Only when the user is seated and the buzzer beeps, then the functions of front/rear washing
and drying can be activated. · Please sit backward on the seat for correct washing position and to avoid splashing. · The nozzle will continue to spray for 1-2 seconds after user stands up during washing, so
please press “STOP” button before standing up.
REAR|MOVE
· Press ” ” button, the indicator light is on showing current water temperature level, it starts rear washing; Press again ” ” button to shift to oscillating washing (nozzle moves forward and backward to expand washing area). The washing will stop automatically after one cycle, while it will stop immediately if the user presses ” ” button.
FRONT|MOVE
· Press ” ” button, the indicator light is on showing current water temperature level, it starts front washing; Press again ” ” button to shift to oscillating washing (nozzle moves forward and backward to expand washing area). The washing will stop automatically after one cycle, while it will stop immediately if the user presses ” ” button.
DRY DRYER TEMP.
Rear washing
Front washing 03
Usage Instruction
DRY|DRYER TEMP
Press ” ” button, the indicator is on, showing the current air temperature level. It will stop drying automatically after one cycle or after leaving. Under drying, press ” ” button to adjust the air temperature between 0-5 level, and the indicator light is on showing the air temperature level. When the indicator light is off, the temperature is at level 0 (room temperature).
Drying
Room
Level 1
temperature
Level 2
Level 3
Level 4
Level 5
Water volume adjustment
· Press “+” or ” – ” button when it is under function of rear washing or front washing, the indicator light is on showing current water volume level, and water volume can be adjusted.
Nozzle position adjustment
· Press “” or “” button when it is under function of rear washing or front washing, the indicator light is on showing current nozzle position, and nozzle position can be adjusted in 5 levels.
Water volume
Nozzle
Energy saving
Long press ” ” button to enter energy saving mode, long press ” to exit energy saving mode.
” button again
Under energy saving mode, seat temperature is set to Level 1 for energy saving. (Note: If the seat temperature before energy saving is neutral, then it will be neutral as well.)
Remark: Energy saving mode will be suspended and the product will enter functional mode if the seat is used. The seat starts to heat immediately (without turning off the seat temperature), and the energy saving mode is restored once the seat is no longer being used.
04
Usage Instruction
Water temperature adjustment
Short press ” ” button to adjust the water temperature between 0-5 level. The indicator light is on showing current water temperature level. When the indicator is off, the temperature is at level 0 (room temperature).
Room
Level 1
temperature
Level 2
Level 3
Level 4
Level 5
Seat temperature adjustment
Short press ” ” button to adjust the seat temperature between 0-5 level. The indicator light is on showing current seat temperature level. When the indicator is off, the temperature is at level 0 (room temperature).
Room
Level 1
temperature
Level 2
Level 3
Level 4
Level 5
Night light
· Night light adjustmentShort press ” ” button to turn on/turn off night light.
· Intelligent mode: Long press ” ” button to enter into intelligent mode (Night light
LIGHT
will be on or off depending on the surrounding light.). If the product is on intelligent
mode, short press ” ” button to exit intelligent mode. (Factory setting: intelligent
mode)
Half flush/Full flush
· Short press ” · Short press ” · Long press ”
” button, the toilet starts half flushing. ” button, the toilet starts full flushing. ” button to turn on/off auto flush function.
When the auto flush function is turned on, toilet will automatically flush after detecting user leaving the seat.
FULL FLUSH HALF FLUSH 05
Usage Instruction
Auto lid open/close
Short press ” Short press ” Long press ”
” buttonopen or close the lid. ” buttonopen or close the seat. ” button to turn on/off auto lid open/close function.
Auto deodorization
DEODORIZER
Short press ” ” button to turn on/off auto deodorization function. The deodorization function will be automatically turned on when the user is seated, and will stop after leaving. Under drying, deodorization will stop. (This function is turned on by default.)
User code
· IR remote control
Plug in the toilet and the self-inspection starts. It beeps when the self-inspection completes. Press and hold ” ” button, then press ” ” button, the indicator light will flash. Press and hold the Pressure ” + ” or ” – ” button to select user 1-9 (as shown below). The indicator light displays the corresponding user code and flashes. Press ” ” button, then press ” ” button. The main unit beeps once, indicating that the remote control and the toilet are matched successfully.
User 1 User 7
User 2 User 8
User 3 User 9
User 4
User 5
User 6
06
Usage Instruction
Other operations
Quiet mode
· Press and hold the ”
” button and press the ”
” button to turn on/off quiet mode.
Automatic pre-wetting function
· Press and hold ” ” button and press ” ” button to turn on or off automatic pre-wetting function. After the automatic pre-wetting function is turned on, the pre-wetting function will be performed when the user is detected to be seated. (Only for the toilet with automatic pre-wetting function.)
Foot sensor function
· Long press ” ” button to turn on/off foot sensor function. Foot sensor is deactivated when the user is seated. (Only for the toilet with foot sensor function.)
Four Seasons Temperature Sensing function
Long press ” ” button to activate the Four Seasons Temperature Sensing function, indicated by a single beep. Once activated, the unit will intelligently adjust the water temperature, air temperature, and seat temperature based on the external environment. Long press ” ” button again to deactivate the Four Seasons Temperature Sensing function, indicated by two beeps. (The Four Seasons Temperature Sensing function is set to off by default and needs to be activated for first-time use.)
Remark:
· The buzzer will “BEEP” once when the user presses one button indicating that the main unit receives the signal and conduct the operation accordingly. If the buzzer doesn’t sound, it means the main unit doesn’t receive the signal, please adjust the remote control direction and repress the button.
· In case of power cut during nozzle spraying, the wand cannot be retracted, please wait until the power is restored. In case of a power cut for a long period, please push the wand softly back by hand. Do not push hard, to avoid damage to wand and electrical machine.
07
Get free technical support for the lifetime of your product. Email: service@canesthome.com Phone: 1-702-824-3195
ASVFAF0446002A-1.2
Documents / Resources
 |
CANEST FC-001 Remote Control [pdf] Installation Guide FC-001, FC-001 Remote Control, Remote Control |