cameo AZOR W2 CLAZORW2 LED Wash Moving Head
Product Information
Specifications
- Product Name: LED WASH MOVING HEAD CLAZORW2
- Dimensions: Refer to manual Section DIMENSIONS (22)
- Minimum Distance to Illuminated Surface: Refer to manual Section MINIMUM DISTANCE TO ILLUMINATED SURFACE (24)
- Minimum Distance to Normally Flammable Materials: Refer to manual Section MINIMUM DISTANCE TO NORMALLY FLAMMABLE MATERIALS (24)
Product Information
You have made the right choice! The LED WASH MOVING HEAD CLAZORW2 has been developed and manufactured to the highest quality standards to ensure many years of trouble-free operation. Please read this user manual carefully to be able to quickly put your new Cameo Light product to optimum use.
Further information about Cameo Light is available on our website CAMEOLIGHT.COM.
Product Usage Instructions
Information on this User Manual
This user manual is an integral part of the product. It provides essential guidance on the setup, operation, and maintenance of the LED WASH MOVING HEAD CLAZORW2.
Definitions and Symbol Explanations
- DANGER: Indicates immediately dangerous situations or conditions for life and limb.
- WARNING: Indicates potentially dangerous situations or conditions for life and limb.
FAQ
- What should I do if the device is not functioning correctly?
- If you encounter any issues with the LED WASH MOVING HEAD CLAZORW2, refer to the troubleshooting section in the user manual. If problems persist, contact customer support for assistance.
- How do I clean and maintain the product?
- For cleaning and maintenance instructions, please refer to the CARE, MAINTENANCE, AND REPAIR section in the user manual. Regular maintenance will help ensure optimal performance of the product.
“`
ENGLISH YOU HAVE MADE THE RIGHT CHOICE! This device has been developed and manufactured to the highest quality standards to ensure many years of trouble-free operation. Please read this user manual carefully to be able to quickly put your new Cameo Light product to optimum use. Further information about Cameo Light is available on our website CAMEOLIGHT.COM.
SAFETY INFORMATION
INFORMATION ON THIS USER MANUAL
· Carefully read the safety instructions and the entire manual before operating the device. · Observe the warnings on the device and in the user manual. · Always keep the user manual within reach. · If you sell or pass on the device, it is important that you also include this user manual, as it is an
integral part of the product.
INTENDED USE
This product is a device for event technology! This product has been developed for professional use in the field of event technology and is not suitable for use as domestic lighting! Furthermore, this product is only intended for qualified users with specialist knowledge of event technology! Use of the product outside the specified technical data and operating conditions is considered improper use! Liability for damage and third-party damage to persons and property due to inappropriate use is excluded! The product is not suitable for: · Use by persons (including children) with limited physical, sensory or mental abilities or lack of
experience and knowledge. · Children (children must be instructed not to play with the device).
DEFINITIONS AND SYMBOL EXPLANATIONS
1. DANGER: The word DANGER, possibly in combination with a symbol, indicates immediately dangerous situations or conditions for life and limb.
2. WARNING: The word WARNING, possibly in combination with a symbol, indicates potentially dangerous situations or conditions for life and limb.
3. CAUTION: The word CAUTION, possibly in combination with a symbol, is used to indicate situations or conditions that may lead to injury.
4. ATTENTION: The word ATTENTION, possibly in combination with a symbol, refers to situations or conditions that can lead to damage to property and/or the environment.
This symbol identifies hazards that can cause electric shock.
This symbol identifies hazardous areas or hazardous situations.
This symbol indicates hazards caused by hot surfaces.
This symbol indicates hazards caused by intense light sources.
This symbol indicates a device in which there are no user-replaceable parts.
This symbol indicates additional information on the operation of the product.
This symbol indicates a device that may only be used in dry rooms.
SAFETY INSTRUCTIONS
DANGER: 1. Do not open or modify the device. 2. If your device no longer functions properly, if liquids or objects get inside it or if it has been damaged in any other way, switch it off immediately and disconnect it from the mains. The device may be repaired only by authorised repair technicians. 3. For devices of protection class 1, the protective earth conductor must be connected correctly. Never disconnect the protective earth conductor. Devices of protection class 2 do not have a protective earth conductor. 4. Ensure that live cables are not kinked or otherwise mechanically damaged. 5. Never bypass the device fuse.
WARNING: 1. The device must not be used if it shows obvious signs of damage. 2. The device may only be installed in a voltage-free state. 3. If the power cable of the device is damaged, do not operate the device. 4. Permanently connected power cables may only be replaced by a qualified person.
ATTENTION: 1. Do not switch on the device if it has been exposed to extreme temperature fluctuations (for example, following transport). Moisture and condensation can damage the device. Switch on the device only when it has reached ambient temperature. 6
2. Make sure that the voltage and frequency of the mains supply correspond to the values indicated on the device. If the device has a voltage selector switch, do not turn the device on until it has been set correctly. Use only suitable power cables.
3. To disconnect the device from the mains at all poles, it is not sufficient to press the on/off switch on the unit.
4. Make sure that the fuse used corresponds to the type printed on the device. 5. Make sure that appropriate measures have been taken against overvoltage (e.g.
lightning strike). 6. Observe the specified maximum output current on devices with a Power Out con-
nection. Ensure that the total current consumption of all connected devices does not exceed the specified value. 7. Replace plug-in power cables only with original cables. 8. Connect the device only to compliant, tested and undamaged power outlets.
DANGER: 1. Danger of suffocation! Plastic bags and small parts must be kept out of reach of
persons (including children) with reduced physical, sensory or mental capabilities. 2. Danger caused by falling device! Make sure that the device is securely installed
and cannot fall down. Only use suitable stands or mounts (particularly for fixed installations). Ensure that accessories are properly installed and secured. Ensure that all applicable safety regulations are observed.
WARNING: 1. Use the device in the prescribed manner only. 2. Operate the device using only accessories of the type recommended and supplied
by the manufacturer. 3. During installation, observe the safety regulations applicable in your country. 4. After connecting the device, ensure that all cables are routed so as to avoid dam-
age or accidents, such as from tripping. 5. Be sure to observe the specified minimum distance to normally flammable materi-
als! Unless explicitly stated, the minimum distance is 0.3 m.
CAUTION: 1. Moving components such as mounting brackets pose a jamming hazard. 2. In the case of devices with motor-driven components, there is a risk of injury from
the movement of the device. Sudden movement of the device can cause shock reactions. 3. The exterior surface of the device can become very hot during regular operation. Ensure that accidental touching of the housing is not possible. Always allow the device to cool sufficiently before removal, maintenance work and charging etc.
ATTENTION: 1. Do not install and operate the device in the vicinity of radiators, heat accumulators,
ovens, or other heat sources. Ensure that the device is always installed in such a way that it is sufficiently cooled and cannot overheat. 2. Do not place ignition sources such as lighted candles near the device. 3. Vents must not be covered and fans must not be blocked. 4. Use the original packaging or packaging provided by the manufacturer for transport. 5. Avoid shock or impact to the device. 6. Observe the IP rating as well as the ambient conditions such as temperature and humidity according to the specification. 7. Devices can always be further improved. In the event of any discrepancies between the operating instructions and the device labelling with regard to operating conditions, performance or other device characteristics, the information on the device always takes precedence. 8. The device is not suitable for tropical climates and for operation at elevations higher than 2000 m above sea level. 9. Unless explicitly stated, the device is not suitable for operation in marine conditions.
PLEASE NOTE: For conversion or retrofit sets or accessories provided by the manufacturer, it is essential to observe the included instructions.
CAUTION! IMPORTANT INFORMATION REGARDING LIGHTING PRODUCTS! 1. Never look directly into the beam of light, not even for a short period of time. 2. Never look into the beam of light using optical devices such as a magnifying glass.
3. Stroboscopic effects may cause epileptic seizures in susceptible individuals!
4. Permanently installed lamps are built into these lighting units. These may not be replaced by the user. The lamps contained in this lighting unit may only be replaced by the manufacturer, its service partner, or a similarly qualified person.
SIGNAL TRANSMISSION BY RADIO (e.g. W-DMX or wireless audio systems): The quality and performance of wireless signal transmissions generally depends on the ambient conditions. For example, the following factors can impact range and signal quality: Shielding (e.g. masonry, metal structures, water) High volumes of radio traffic (e.g. powerful wireless LAN networks) Interference Electromagnetic radiation (e.g. LED video screens, dimmers) All range specifications refer to free-field line-of-sight applications without interference!
The operation of radio systems is subject to official regulations. These may vary from region to region and must be checked by the operator before use (e.g. radio frequency and transmission power).
WARNING: Wireless transmitting devices are not suitable for use in sensitive areas in which radio operation can lead to potential detrimental effects. These include e.g.: · Hospitals, health centres or other healthcare facilities that provide patient treatment
with skilled personnel and equipment. · Hazardous areas Class I, II and III · Restricted areas · Military facilities · Aircraft or vehicles · Areas where the use of mobile phones is prohibited
TRANSMISSION VIA W-DMX WARNING: In general, wireless DMX transmission must not be used for applications involving safety-related factors that might result in personal injury or property damage in the event of a failure. This applies in particular to moving scene or traverse structures, DMX-controlled motors/lifts or lifting devices for operating DMX-operated platform lifts, hydraulic systems or comparable moving components. Furthermore, wireless DMX transmission must not be used to control flame or pyrotechnic devices, explosion effects, or gas or liquid effects. These include CO2 cannons, confetti shooters, water effects or similar.
ATTENTION! POTENTIAL DAMAGE FROM EXTERNAL LIGHT SOURCES! Solar radiation, laser radiation and bundled light beams from other spotlights can damage the housing and internal components such as filters, gobo and colour wheels, motors, cables, belts, etc., as well as light sources! Do not expose the device and especially the lens opening to direct sunlight, laser radiation and bundled light beams from other spotlights during unpacking, installation, prolonged disuse and operation! Always point the lens opening towards the floor when the device is not in use! Damage caused by external light sources is excluded from the manufacturer’s warranty!
NOTES ON PORTABLE INDOOR DEVICES
1. Temporary operation! Event equipment is generally only designed for temporary operation.
2. Continuous operation or permanent installation can impair the functionality of the device and cause premature ageing.
PACKAGING CONTENT
Remove the product from the packaging and remove all packaging material. Please check the completeness and integrity of the delivery and notify your distribution partner immediately after purchase if the delivery is not complete or if it is damaged. The packaging content includes: X 1 x AZOR W2 LED Moving Head X 1 x Power cable X 2 x Omega bracket X 1 x User manual
INTRODUCTION
LED moving head CLAZORW2
CONTROL FUNCTIONS: 19-channel, 18-channel HSI, 18-channel RGBL, 23-channel RGBL, 34-channel HSI, 36-channel RGB, 43-channel RGBL, 44-channel RGBL and 54-channel Full Access DMX control DMX512 W-DMXTM via optional Cameo iDMX stick RDM Master / slave operation Standalone functions
FEATURES: 7 x 40 W RGBL LEDs plus 48 x 2 W white effect LEDs. DMX512. Connection for optional iDMX stick for wireless control via W-DMXTM. 5-pin DMX connections. 2 Omega mounting brackets included.The spotlight supports the RDM standard (Remote Device Management). Remote device management allows the user to monitor the status and configuration of RDM devices using an RDM-capable controller, such as the optionally available Cameo UNICON (item number CLIREMOTE). The Cameo UNICON also allows access to the entire spotlight menu.
CONNECTIONS, OPERATING AND DISPLAY ELEMENTS
3
4
7
1
2
6 5
DEUTSCH
FRANCAIS
8 9
ESPAÑOL
POLSKI
1 POWER IN TRUE1-compatible mains input socket. Operating voltage 100 – 240 V AC / 50 – 60 Hz. Use the included power cable.
2 POWER OUT TRUE1-compatible mains output socket. Enables power supply to other CAMEO spotlights. Ensure that the total power consumption of all connected devices does not exceed the value specified on the device in amperes (A).
3 FUSE Fuse holder for 5 x 20 mm fuses. IMPORTANT NOTE: Only replace the fuse with a fuse of the same type and value. In the event of repeated fuse failure, please contact an authorised service centre.
4 DMX IN Male 5-pin XLR socket for connection to a DMX control device (e.g. DMX console).
5 DMX OUT Female 5-pin XLR socket for forwarding the DMX control signal.
11
ITALIANO
DMX
ENGLISH
DEUTSCH
FRANCAIS
ESPAÑOL
6 IDMX STICK Connection for the optional iDMX stick for W-DMXTM operation (insert the iDMX stick with the antenna facing upwards). Note the wireless settings in the Settings menu.
7 AIR VENTS To prevent damage to the device, do not cover the ventilation openings on the back and ensure that air can circulate freely.
8 OLED DISPLAY The OLED display shows the currently active operating mode (main screen), the menu items and the numerical value or operational status of certain menu items. If no input is made within approximately one minute, the display automatically returns to the main screen. Note on the main screen in operating modes with external control: In the event that the control signal is interrupted, the characters in the display begin flashing; once the control signal is present again, the flashing stops.
9 CONTROL BUTTONS MENU Press MENU to access the main menu. Press again or repeatedly to return to the main screen. Pressing MENU without confirming a value or status change by pressing ENTER restores the previously confirmed value or status. ENTER Press ENTER to access the menu and submenus. ENTER is also used to confirm value or status changes. and Select menu items in the main menu (DMX address, DMX mode etc.) and in the submenus. Allows you to change the value of a menu option, such as the DMX address (long press = quick value change).
OPERATION
NOTES Upon switching on the spotlight, the message “Update Wait” is displayed momentarily, followed by “Welcome to Cameo”, the model name and the software version. Thereafter, the motors are reset (Motor Reset Please Wait). After this process, the spotlight is ready for operation and the previously activated operating mode is launched.
12
POLSKI
ITALIANO
DMX
ENGLISH
DEUTSCH
FRANCAIS
ESPAÑOL
MAIN SCREEN IN DMX OPERATING MODE In DMX mode, the main screen shows the currently set DMX start address (see illustration). Flashing characters indicate that no DMX signal is present.
SET DMX START ADDRESS (DMX Address) Starting from the main screen, press MENU to enter the main menu. Now use or to select the menu item DMX Address and confirm with ENTER. Use the or buttons to configure the desired DMX start address and press ENTER to confirm (the highest possible value depends on the selected DMX mode).
CONFIGURING DMX MODE (DMX MODE) Starting from the main screen, press MENU to enter the main menu. Now use or to select the menu item DMX Mode and confirm with ENTER. Select the desired DMX operating mode using or and confirm with ENTER. Tables showing the channel assignment of the different DMX modes can be found in the DMX CONTROL section of this user manual.
STAND-ALONE MENU In the stand-alone operating modes (Play Scene and Play Loop), the control signal of the corresponding mode can be output to slave units via XLR. If you do not want to output the control signal, deactivate the output.
13
POLSKI
ITALIANO
DMX
ENGLISH
DEUTSCH
FRANCAIS
ESPAÑOL
A delay can be set for slave units for the time-delayed output of the control signal of the stand-alone operating modes. Activate one of the eight available scenes (Scene 1 – 8) or one of the eight available loops (Loop 1 – 8). The settings are made individually for each scene and each loop and are retained even after the device is restarted. Starting from the main screen, press MENU to enter the main menu. Use the or buttons to select the Stand Alone menu item and confirm with ENTER. Now select the desired submenu item, confirm and then make the settings as required (see table).
Forward control signal via DMX OUT and set delay for slave units: Off, 0.1s – 2.0s Do not forward control signal
Select and activate the desired scene
Select and activate the desired loop
Set each scene individually. Scenes are activated by selecting them.
Select scene 1 – 8 Set step time Set fade time ” Select scene 1 – 8 / skip step Set step time Set fade time ” ” ” ” ”
14
POLSKI
ITALIANO
DMX
ENGLISH
DEUTSCH
FRANCAIS
SLAVE MODE
Standard slave operation: Starting from the main screen, press MENU to enter the main menu. Use the or buttons to select the Slave menu item, confirm with ENTER, then select slave group 0 and confirm again. Connect the slave and master units (same model, same software version) using a DMX cable and activate the control signal output (Stand Alone -> Master/Alone -> Master) and one of the stand-alone operating modes (Play Scene/Loop) in the master unit. The slave unit will now follow the master unit.
Advanced slave mode: If you wish to control the slave units in master/slave mode using one of the Play Scene or Play Loop stand-alone modes, the control signal can be played back with a time delay of up to 24 steps. The delay is set in the Stand Alone menu Master/Alone in the master unit; the delay factor is set in the slave menu of the corresponding spotlight (Group). This is a simple way to create a running light effect with a large number of identical spotlights that are running the same software version, which would otherwise require a suitable DMX controller and extensive programming. Connect the slave and master units (same model, same software version) using a DMX cable and activate the control signal output (Stand Alone -> Master/Alone -> Master) and one of the stand-alone operating modes (Play Scene/Loop) in the master unit.
Group
0-24
Set the slave group for signal delay
Assign the spotlights to one of up to 24 groups (plus Group 0) according to preference, whereby several spotlights can be assigned to one group. The group number is also the factor by which the delay time set in the master unit is multiplied.
Setup example:
ESPAÑOL
POLSKI
ITALIANO
DMX
15
SYSTEM SETTINGS (Settings)
Starting from the main screen, press MENU to enter the main menu. Use the or buttons to select the menu item Settings and confirm with ENTER.
ENGLISH
DEUTSCH
FRANCAIS
ESPAÑOL
POLSKI
This takes you to the submenu (see table). Select submenu items with or , confirm with ENTER, change value or status with or , confirm with ENTER).
(Bold print = factory setting)
Wireless Settings (iDMX stick optional)
Wireless control deactivated Wireless control activated
Signal -> DMX OUT
Backup via DMX IN in case of W-DMX signal interruption
W-DMX reception only
Display Settings
Display rotation by 180° (e.g. for overhead installation)
No display rotation
Permanently on
Dimmer Settings
(Dimmer curve)
16
Deactivates after approximately 20 seconds of inactivity
Autolock function deactivated
Controls locked after approx. 60 seconds without input (LOCKED). To unlock, press MENU for approx. 3 seconds.
Light intensity increases linearly with DMX value
Light intensity can be finely adjusted at lower DMX values and broadly adjusted at higher DMX values
Light intensity can be broadly adjusted at lower DMX values and finely adjusted at higher DMX values
ITALIANO
DMX
ENGLISH
Dimmer Settings
(Dimmer curve)
Light intensity can be finely adjusted at lower and higher DMX values and broadly adjusted at medium DMX values
Select LED PWM frequency
DEUTSCH
FRANCAIS
ESPAÑOL
POLSKI
(Dimmer response) Colour calibration
Set head movements
Fan settings
The spotlight responds immediately to changes of the DMX value The spotlight behaves in a similar way to a halogen spotlight with gradual changes of brightness R, G, B, and L (maximum value: 255) Custom colour calibration. Brightness setting of R, G, B and L with values ranging from 0 – 255 Factory calibration Merging factory and RAW calibration Pan direction not reversed Pan direction reversed Tilt direction not reversed Tilt direction reversed Pan angle 540° Pan angle 630° Automatic position correction disabled Automatic position correction enabled No blackout during head movement Blackout during head movement Function disabled Slowed motor movements for quieter operation Automatic fan control Deactivated fan with greatly reduced brightness Constant low fan speed with reduced brightness, if necessary Constant average fan speed with reduced brightness, if necessary Constant high fan speed
17
ITALIANO
DMX
ENGLISH
DEUTSCH
Operational status in case the DMX signal is interrupted
Mirror pixels
Save settings in 3 custom presets
Last command is retained The last selected stand-alone operating mode is activated 10 second fade to blackout Activates blackout Full On Function disabled Mirror pixels horizontally Flip pixels vertically
Flip pixels horizontally and vertically
Save all current settings as user preset A Save all current settings as user preset B Save all current settings as user preset C
SERVICE MENU (Service)
Starting from the main screen, press MENU to enter the main menu. Use the or buttons to select Service and confirm with ENTER.
FRANCAIS
ESPAÑOL
POLSKI
ITALIANO
Information on the submenu items in the Service menu and the corresponding options can be found in the table below (select with or , confirm with ENTER, change value or status with or , confirm with ENTER).
Reset to factory setting
Resets to User A values (store user values: Settings -> Store Default) Resets to User B values (store user values: Settings -> Store Default) Resets to User C values (store user values: Settings -> Store Default) Reset pan / tilt motors Reset motors in the device head Reset all motors
18
DMX
ENGLISH
Pre-programmed sequence to test all components Pre-programmed sequence to test all components under maximum load Activate all motors individually with values of 000 to 255 Do not reset service operation time Reset service operation time
SYSTEM INFORMATION (System Info) Starting from the main screen, press MENU to enter the main menu. Use the or buttons to select the menu item System Info and confirm with ENTER.
DEUTSCH
FRANCAIS
ESPAÑOL
POLSKI
This takes you to the submenu (see table for submenu items). Select submenu items with or , confirm with ENTER, change value or status with or , confirm with ENTER).
Display the firmware version of the corresponding component
Display the temperature of the corresponding component
(Celsius) (Fahrenheit)
Set temperature unit
Display the speed of the corresponding fans
Total operating time Time in use Lamp operating time Operating time since the last reset of the service operating time (unique identifier) Error display in case of malfunction
19
ITALIANO
DMX
ENGLISH
QUICKLIGHT
Set up a scene quickly and easily using the basic Moving Head functions without an external controller. Starting from the main screen, press MENU to access the main menu. Use or to select Quicklight and confirm with ENTER. Now select the desired submenu item, confirm, set the value as required and confirm again.
DEUTSCH
FRANCAIS
ESPAÑOL
POLSKI
If the Quicklight mode is activated, the display does not automatically return to the main screen. Quicklight mode is automatically cancelled when you exit the Quicklight menu. The Quicklight settings are retained until the next restart of the spotlight. Quicklight can be accessed repeatedly with the same settings as long as the spotlight remains switched on. After a restart, the values are reset to the factory settings.
SETUP AND INSTALLATION
DANGER: Overhead mounting requires extensive experience, including calculating the load limit values of the mounting hardware and regular safety inspection of all installation materials and spotlights. If you do not have these qualifications, do not attempt to perform an installation yourself. Refer instead to a qualified professional. There is a risk that devices that are incorrectly mounted and secured may come loose and fall down. This can cause serious injury or death.
Thanks to its integrated rubber feet, the spotlight can be positioned in a suitable location on a level surface. It can be truss-mounted using two Omega brackets, which are attached to the base of the device (A). Two Omega brackets are included. Suitable truss clamps are available as an option. Ensure firm connections and secure the spotlight to the securing lug (B) with a suitable safety cable.
B
A
A
20
– Illustrations similar –
ITALIANO
DMX
ENGLISH
DEUTSCH
FRANCAIS
ESPAÑOL
CARE, MAINTENANCE AND REPAIR
In order to ensure the long-term, proper functioning of the device, it must be regularly cleaned and, if necessary, serviced. The maintenance requirement depends on the intensity of use and the environment in which it is used. We recommend a visual inspection before each operation. Furthermore, we recommend carrying out all the applicable service measures specified below once every 500 operating hours or, in the case of a lower intensity of use, at the latest after one year. Warranty claims may be limited should defects result from inadequate service and maintenance.
CARE (can be performed by the user) WARNING! Before carrying out any care or maintenance, the power supply and, if possible, all device connections must be disconnected.
PLEASE NOTE! Improper care can lead to impairment or even destruction of the device.
1. Housing surfaces must be cleaned with a clean, damp cloth. Make sure that no moisture can penetrate the device.
2. Air inlets and outlets must be regularly cleaned of dust and dirt. If compressed air is used, make sure that damage to the device is prevented (e.g. fans must be blocked in this case).
3. Cables and connectors must be cleaned regularly and dust and dirt must be removed. 4. In general, no cleaning agents or abrasive agents may be used, otherwise the surface finish
may be damaged. 5. Devices must be stored in a dry environment and protected from dust and dirt.
MAINTENANCE AND REPAIR (by qualified personnel only) DANGER! There are live components in the device. Even after disconnecting the mains connection, there may still be residual voltage in the device, e.g. due to charged capacitors.
PLEASE NOTE! There are no user-serviceable assemblies in the device.
NOTE! Maintenance and repair work may only be carried out by specialist personnel authorised by the manufacturer. If in doubt, consult the manufacturer.
NOTE! Improperly performed maintenance work may affect warranty claims.
21
POLSKI
ITALIANO
DMX
DIMENSIONS (mm)
289
102
128
ENGLISH
DEUTSCH
414 375
FRANCAIS
ESPAÑOL
POLSKI
308
193
TECHNICAL SPECIFICATIONS
Product number:
CLAZORW2
Product type:
LED moving light
Type:
Wash light
Colour spectrum (Centre LEDs): RGBL
Number of centre LEDs:
7
LED type (Centre LEDs):
40 W
CCT (Centre LEDs):
2200 K – 8000 K
Luminous flux (Centre LEDs):
3600 lm
Light intensity:
4100 lx @ 10 m, narrow zoom
CRI (Centre LEDs):
84
Dispersion (half-peak divergence): 4,3° – 34° (6,2° – 50,9°)
Colour spectrum (FX LEDs):
Cold White
Number of FX LEDs:
4 segments with 12 LEDs each (48 LEDs in total)
LED type (FX LEDs):
2 W
PWM frequency:
650 Hz; 1530 Hz; 3600 Hz; 12 kHz; 18.9 kHz; 25 kHz
DMX input:
5-pin male XLR
DMX output:
5-pin female XLR
22
ITALIANO
DMX
Control:
DMX mode:
DMX functions:
Standalone functions: Pan angle: Tilt angle: Controls: Display: Operating voltage: Power consumption: Inrush current: Power supply connection: Power Link: Fuse: Ambient temperature (in operation): Relative air humidity: IP protection class: Minimum distance to illuminated surface: Minimum distance to normal flammable materials: Housing material: Housing colour: Housing cooling: Dimensions (W x H x D, without mounting bracket): Weight:
DMX512, RDM, iDMX stick compatible 19-CH Effect,18-channel HSI, 18-channel RGBL, 23-channel RGBL, 34-channel HSI, 36-channel RGB, 43-channel RGBL, 44-channel RGBL, 54-channel Full Access Pan (fine); Tilt (fine); Dimmer (fine); Strobe Functions; Red (fine); Green (fine); Blue (fine); Lime (fine); Hue (fine); Saturation; Colour Temperature; Tint; Colour Presets; Dimmer FX 1-4; FX Strobe; FX Pattern Selection; FX Pattern Speed, Pattern Folder; Pattern Selection; Pattern Position & Speed; Pattern Transition; Pattern Fade/Wake Effect; Background Dimmer (fine) + Strobe + Red (fine) + Green (fine) + Blue (fine) + Lime (fine) + Hue (fine) + Saturation + Colour Temperature + Tint + Colour Presets; Zoom (fine); Device Settings; Red 1-7; Green 1-7; Blue 1-7; Lime 1-7, Device Settings User Scene 1-8, Loop 1-8, Quick Light, Master/slave operation 540°/630° 250° MENU, ENTER, up arrow, down arrow OLED display 100240 V AC / 5060 Hz 480 W 96 A @ 0.358 ms True1 compatible input and output (Max. output current 9.5 A) Up to 5 devices @ 230V; up to 3 devices @ 110V T4AL/250 V (5 x 20 mm)
0 40°C 40°C
< 85%, non-condensing IP20
0.5 m
0.5 m
Metal, ABS Black Temperature-controlled fan
308 x 414 x 193 mm
8.6 kg 23
DMX
ITALIANO
POLSKI
ESPAÑOL
FRANCAIS
DEUTSCH
ENGLISH
ENGLISH
DEUTSCH
FRANCAIS
RDM UID: Additional features:
0x08A40057XXXX
Power cable (1 m) with True1-compatible plug and 2 x Omega mounting brackets included
MINIMUM DISTANCE TO ILLUMINATED SURFACE
This symbol with the distance stated in metres (m) indicates the minimum dis-
0.5 m
tance of the light fixture to the illuminated surface. In this example, the distance is 0.5 m. For the applicable value for this device, please refer to the technical
specifications in this manual and the imprint on the device!
MINIMUM DISTANCE TO NORMALLY FLAMMABLE MATERIALS
This symbol with the distance stated in metres (m) indicates the minimum
0.5 m
distance of the device to normally flammable materials. In this example, the distance is 0.5 m. For the applicable value for this device, please refer to the
technical specifications in this manual!
DISPOSAL
PACKAGING: 1. Packaging can be recycled using the usual disposal methods. 2. Please separate the packaging in accordance with the disposal laws and recycling
regulations in your country.
DEVICE: 1. This device is subject to the European Directive on Waste Electrical and Electronic
Equipment as amended. WEEE Directive Waste Electrical and Electronic Equipment. Electronic devices do not belong in household waste. The device must be disposed of via an approved disposal company or a municipal disposal facility. Please observe the applicable regulations in your country! 2. Observe all disposal laws applicable in your country. 3. As a private customer, you can obtain information on environmentally-friendly disposal options from the seller of the product or the appropriate regional authorities.
MANUFACTURER’S DECLARATIONS
Manufacturer’s warranty & limitation of liability Adam Hall GmbH | Adam-Hall-Str.1 | 61267 Neu-Anspach | Germany E-mail: Info@adamhall.com / +49 (0)6081 / 9419-0 Our current warranty conditions and limitation of liability can be found at: https://cdn-shop.adamhall.com/media/pdf/Manufacturers-Declarations-CAMEO_DE_EN_ES_FR.pdf For service requests, please contact your distribution partner. CE conformity Adam Hall GmbH hereby confirms that this product meets the following guidelines (where applicable): Low-Voltage Directive (2014/35/EU) EMC Directive (2014/30/EU) RoHS (2011/65/EU) RED (2014/53/EU) EC Declaration of Conformity Declarations of conformity for products subject to the LVD, EMC, RoHS Directive can be requested from info@adamhall.com Declarations of conformity for products subject to RED can be downloaded from www.adamhall.com/compliance/
Subject to misprints and errors, as well as technical or other modifications!
Documents / Resources
 |
cameo AZOR W2 CLAZORW2 LED Wash Moving Head [pdf] User Manual W2, AZOR W2 CLAZORW2 LED Wash Moving Head, AZOR W2 CLAZORW2, LED Wash Moving Head, Wash Moving Head, Moving Head, Head |
