Height Adjustable Desk Return Frame
“
Specifications:
- Product Name: Boost Crank Height Adjustable Desk Return
frame - Adjustable Height: Yes
- Material: Steel
- Dimensions: Standard single workstation size
Product Usage Instructions:
Component Parts:
- Hand bolts M6x10 – 4 PCS
- Leveling pads – 2 PCS
- Table feet – 1 PC
Assembly Instructions:
Step 1:
Loosen the pre-installed bolts and adjust the length of the top
frame to match the size of the table top.
Step 2:
Inset the lifting column to the top frame. First fix 2 screws
M6x12 and then tighten the pre-installed bolts.
Step 3:
Install the table feet with 4 PCS M6x16 bolts and add the
leveling pads.
Step 4:
Connect the return frame to the single workstation and fix it
with hand bolts and screws as instructed.
Step 5:
Adjust the centre brackets, tighten them with screws, and
connect the return frame to the single workstation using bolts.
Step 6:
Fix the desk frame to the tabletop with ST4X16 screws and
install the manual crank holder with ST4X16 screws.
Add-Ons:
Cable Tray Installation:
Fix the cable tray to the arms with M6x10 screws.
Screen Panel Installation:
Insert tapped plates to the screen panel, install brackets with
M5x6 screws, and fix the panel to the desk frame with M6x10
screws.
EPS Screen Panel Installation:
Install screen brackets on the cable tray arm, place the EPS
panel on the screen brackets, drill holes in line with back to back
screen bracket holes, and tighten double-ended bolts.
Frequently Asked Questions (FAQ):
Q: How do I adjust the height of the desk frame?
A: To adjust the height, follow step 1 and step 2 in the
assembly instructions to set it according to your preference.
Q: Can I use this desk frame for a dual workstation setup?
A: Yes, you can connect two single workstations as shown in step
5 to create a dual workstation setup.
“`
Boost Crank Height Adjustable Desk Return frame
Instruction Manual
Table of Contents
Component parts ………………………………………………………………………………………………………………………….. 2 Assembly Instructions …………………………………………………………………………………………………………………….. 3 Use Instructions ……………………………………………………………………………………………………………………………… 6 Troubleshooting …………………………………………………………………………………………………………………………….. 9 Important Safety Instructions …………………………………………………………………………………………………………. 10 Advanced Programming ………………………………………………………………………………………………………………… 11
Return frame
Standard single workstation
1
Component parts
NO. Component Name
PCS
NO. Component Name
PCS
1
Hand bolts M6x10
4
10 transmit
1
2
Leveling pads
2
11 Centre bracket
2
3
Table feet
1
12 Top frame-2
1
4
Lifting column
1
5
Bolt: M6x12
6
6
Screw:ST4x16
8
7
Side brackets
1
8
Rubber pad
8
9
Top frame-1
1
2
Assembly Instructions
Step 1 Loosen the pre-installed bolts and Adjust the length of the top frame to match the size of the table top.
A
Step 2 Inset the lifting column to the top frame. — FFiirrsstt ffiixx 22ppccss ssccrreewwss MM66xx1122 lliikkee CB ddiissppllaayyeedd — AAnndd tthheenn ttiigghhtteenn tthhee pprree–iinnssttaalllleedd bboollttss lliikkee BC ddiissppllaayyeedd
B
C
3
SStetepp33 -InInssttaalllltthheettaabblelefefeeettSwcriethw4s 4PCpScsMM6X6x1160b,ionlsttsall the 4 leveling pads. – Install the leveling feet
Step 4 ICnosntanlel tchtethseidreetburranckfreatmweittho2thPeCSsiMng6lex1w2oBroksltsation and fixed with 2 hand bolts. Fix the centre brackets with 2pcs screws M6x12.
4
Step 5
Connect the return frame to the single dweosrkksatnadtiofinx iatnwditfhixe2dPwCSithM26xh1a2ndBoblotslts. AFidxjuthstetcheenstirdeebbrarackceketst wtoitahli2gpnctshsecrewtusrnMf6raxm10e. and fix it with 2 PCS M6x12 Bolts Insert the hex steel rod to the single workstation and tighten it.
D
E
Step 6 Fix the desk frame to the tabletop with 17 PCS ST4X16 screws Fix the manual crank holder with 2 PCS ST4X16 screws
5 5
Add-On : Cable tray installation Step 1 – Fix the cable tray to the cable tray arms with 8 pcs M6x10 screws.
Step 1 – Install the U brackets to the desk frame with 4 pcs M8x10 screws. – Mount the cable tray to the desk frame and fix it with 6 pcs M6x10 screws
6
Add On : Screen panel installation Step 1 – Insert the tapped plates to the screen panel
Step 2 – Install the brackets to the panel with 8 pcs M5x6 screws.
7
Step 3 – Fix the panel to the desk frame with 10 pcs M6x10 screws.
8
EPS ( 900mm H Eco Panel ) Screen panel installation Step 1 – Install the screen brackets(B2-SBRAC) on the cable tray arm (B2-SSARM)with 10 PCS M6x10 Screws
The brackets direction as photos display.
Step 2 – Place the EPS panel on the screen brackets Using a 6mm drill bit ( not included ), drill out holes in Eco Panel Screen in line with back to back screen bracket holes ( Note: Carbide Drill Bits Work Best For PET panel ) – Place 8 x Double Ended Bolts M5* 32mm – 6mm through The screen bracket ( B2-SBRAC ) holes and the holes you have created in the Eco Panel Screen. Tighten double ended bolt with Allen key.
10
Documents / Resources
 |
Boost Crank Height Adjustable Desk Return Frame [pdf] Instruction Manual Height Adjustable Desk Return Frame, Height Adjustable Desk Return Frame, Adjustable Desk Return Frame, Return Frame, Frame |