Blebox Proxi Dimmer LED Touch Botland
Product Information
Specifications
- Supply Voltage: 12 – 24V
Product Usage Instructions
Installation
- Disconnect the installation supply voltage before installing the controller.
- Ensure the controller is adhered to a non-conductive surface like furniture board or tile.
- Mount the controller in a place protected against adverse environmental conditions and third-party access.
- Clean and dry the surface before sticking the controller using the double-sided adhesive tape provided.
- Connect the power wires (+ and -) and then connect the LED strip, paying attention to polarity.
- Do not place your hand or any conductive objects near the device during the autocalibration process.
Control
To turn on/off the LED strip, close your hand to the controller for approximately 1.5 seconds. Adjust the brightness by holding your hand near the controller.
FAQ
Q: What should I do if the device reacts incorrectly during normal operation?
A: Force the auto-calibration process by disconnecting and reconnecting the power supply to the controller. Avoid placing your hand near the controller for the first 15 seconds after reconnecting.
SAFETY RULES
Do not connect the device to loads exceeding the permitted values.- Connect only under the diagram presented in the manual. Improper connections may be dangerous, they can damage the controller, and loss of the warranty.
- DANGER! Risk of electric shock! Even with the device turned off, the outputs may be live. All assembly work should be ALWAYS performed with the disconnected power circuit.
- Connecting the device to a power supply that does not meet the quality requirements specified in EN 50081-1, EN 50082-1, Ul508, and EN 60950 will invalidate the warranty.
CONNECTION DIAGRAM
General diagram of connection:
INSTALLATION
- Disconnect the installation supply voltage before installing the controller. Remember that any mounting works should be carried out when the mains voltage is disconnected.
- The controller should be installed in a place protected against adverse environmental conditions, and protected from third-party access. It is recommended that the device be mounted in a stable and fixed position.
- Familiarize yourself with the diagram and then proceed with the installation of the controller. Pay special attention to the designation of the controller connectors. Start by connecting the power wires: (+) (red or black with a white dotted line) and (-) (black).
- Connect the LED strip (paying attention to the polarity). The device is equipped with two stripes of double-sided adhesive tape on the bottom side. Before sticking the controller, clean and dry the the surface where it will be adhered.
- Remove the protective film, adhere in the chosen place, and hold for a few seconds. When choosing the mounting location, remember that the device detects the hand only from the side of the adhesive tape.
- The device should adhere to a non-conductive surface, eg furniture board, tile, etc. If the device is not stably fixed or mounted near metal elements, it may not work properly.
- Each time the power source is connected, the device performs the auto-calibration process within the first 15 seconds. During this time, do not place your hand or any conductive objects near the device, as this will affect the calibration process.
- If during normal operation the device reacts incorrectly, force the auto-calibration process by disconnecting and reconnecting the power supply to the controller.
- Remember that after connecting the power supply do not put your hand near the controller for the first 15 seconds!
CONTROL
To turn on / off the LED strip, close your hand to the controller approx. 1.5 sec. Holding your hand near the controller, you can adjust the brightness of the LED strip.
TECHNICAL SPECIFICATIONS
| supply voltage | 12 – 24V |
| energy consumption | <0.1 W |
| maximum current | 5A |
| maximum power | 120W |
| sensor | proximity, capacitive sensor |
| detection range | depending on the material: plexiglass, solid wood, plywood, chipboard – 3cm, metal – -detection with the entire surface, honeycomb panels – no detection |
| calibration | automatic |
| mounting method | under the surface of nonconductive, adhesive tape |
| housing | made of polyurethane composition not containing halogens, self-extinguishing for thermal class B (130 °C) |
| dimensions | 38 x 38 x 19 mm |
| protection level | IP20 |
| controller operating temperature | from -20 to + 50°C |
ADDITIONAL INFORMATION
HELP
- The latest versions of the manual, additional information, and materials about products are available on our website: blebox.eu
- General questions: info@blebox.eu
- Service and technical support: support@blebox.eu
- For more information visit our website www.blebox.eu
- Or send us an email to: info@blebox.eu
- Support is available at support@blebox.eu
- DISTRIBUTED BY Wired 4 Signs USA
- +1 (865) 339 4956 info@w4susa.com
- 7669 Clinton Highway, Powell, Tennessee, 37849
Documents / Resources
 |
Blebox Proxi Dimmer LED Touch Botland [pdf] User Manual Proxi Dimmer LED Touch Botland, Dimmer LED Touch Botland, LED Touch Botland, Touch Botland, Botland |