avitect 59Inch Fixed Frame Screen

Thank you for choosing to use our product! For your better use of the product, please read and keep this manual carefully before installation and use. Due to the improvement of the product, the product you purchased may not be the same as the description in the manual. We apologize for that!

Parts

Precautions

1. To ensure the projection effect and quality of this product, please observe the following operating requirements.
2. When assembling, find a suitable size floor or table. The surface must be clean and free of any obstacles. The floor or table must be covered with clean materials such as cloth, film, blankets, etc.
3. Handle with care during installation to Prevent personal injury or property damage.
4. Do not touch the surface of the projection screen with your hand.
5. Do not touch the projection surface with sharp or hard objects to prevent damage to the screen material. Don’t write or draw on the screen.
6. Keep children away from the screen to prevent accidents.
7. The surface of the screen must be cleaned and treated regularly, and it is recommended to take care of it once every two weeks. Please use a soft cotton cloth to gently wipe (dip some water), and it is not advisable to use any chemical cleaners or alcohol.

Assemble the frame

1. Open the packaging box and categorize and arrange the components properly, and cross-reference the quantities with the “1.0 Parts” checklist.
2. The horizontal frame is a segmented splicing type, and the two horizontal inner frames are spliced correspondingly as shown in the figure
   (Note: There is a mark in the middle of the connecting rod of the inner frame, and the splicing position must be guaranteed to be at the mark).
3. Insert the four corners into the vertical inner frame first, as shown in the figure.
4. Assemble the horizontal and vertical inner frames according to the picture below. After assembling the inner frames, lock the corners with M5X5 screws, then install support rod.

Assemble the screen

1. Wear gloves (to avoid fingerprints on the screen that cannot be erased). Lay a clean cloth on a flat, clean level countertop (or floor) that won’t hurt the screen.
2. Take out the screen from the package, put the screen face down, to unfold the curtain roll, spread it flat on the cloth on the table, and then insert the glass fiber strips around the screen according to the length as shown below.
   Important Note: If it is an ultra-short throw ambient light rejecting screen, please cooperate with two people during assembly, avoid screen folding or hard object friction impact action.
3. Place the assembled frame on the screen.
   Note: This projector screen has up and down directions. The screen should match the direction of the frame. Place the frame at the marking on the four corners of the backside of the screen and adjust the position of the frame.
4. Hook the screen on the frame with a tension spring. To hook the tension spring, please follow the following sequence, first, hook 1~8 springs; then hook springs 9~12, and then hook other springs from the middle spring to both sides in turn. Please refer to the attached drawing next page for the installation method of the tension spring.
5. After hanging the spring, stand the screen up and check the overall flatness of the screen. If there is unevenness, the spring needs to be adjusted locally until it is level.
6. 4.6 is restored to the position of 4.4, ready to install the frame.

Outer Frame Installation

1. Place the outer frame against the frame screen, align the four corners, and lock the inner and outer frames with M4×8 screws.
2. Adjust the outer frame at the corner to the smallest gap, and then tighten the screws. Lock the corners one by one according to this method, and finally deal with the splicing of the horizontal outer frame (if the gap is found to be too large, you can push the left and right outer frames inward)
3. Install the corner protection at the four corners of the screen.

Screen Installation

1. First confirm the upper and under wall bracket and the installation direction
2. Install wall hangers on the wall according to screen size. Required tools: level, hammer, drill, pencil, ladder, etc. As shown below, the horizontal direction is about 30cm away from both sides of the screen. Please estimate the installation position of the screen before installing the wall pendants. The height of the lower edge of the screen from the ground is generally, about 600 to 800mm.
3. Hang the screen on the wall as illustrated.

Troubleshooting in case of waves

1. Remove the outer frame and use your gloves to pull the screen fabric from the center outwards along the edges of the frame to smoothing it.
2. Please check if the screen fabric is tensioned into the 2. Notch with the springs. If not, please tension to the 2. Notch. This will strengthen the screen fabric to the frame.
3. If there will be waves after a few months, this is very likely because of humidity changes / temperature changes. Please retention the screen fabric. See 1.
4. If there are waves in the top middle, this is very likely because the top frame is a bit bent at the point of connection. If you will put a foam behind the frame at this point, these waves will very likely be gone.
5. If you see waves at all, use 2 springs in all edges, this should solve the problem to the inner notch. See photo:

Specifications

• Inner Frame: 6 pieces
• Corner connector: 4 pieces
• Corner Protection: 4 pieces
• Screen: 1 piece
• Pull hook: 1 piece
• Tension Spring: N pieces
• M5 x 5 Pan hat screws: 16 pieces
• Gloves: 1 pair
• User Manual: 1 piece
• Level Ruler: 1 piece
• Expansion Screws: 8 pieces
• Bottom hang piece M4 x 8 Screws: 2 pieces

FAQ

Q: What should I do if the screen fabric is not tensioned properly?
A: Check if the screen fabric is properly tensioned into the notch with the springs. If not, adjust the tension to ensure a tight fit.

Q: How can I eliminate waves in the screen?
A: If waves appear, adjust the frame connections and use additional springs in all edges to ensure proper tension and eliminate waves.

Documents / Resources

avitect 59Inch Fixed Frame Screen [pdf] Instruction Manual 59Inch Fixed Frame Screen, 59Inch, Fixed Frame Screen, Frame Screen, Screen

References

• User Manual