MT02-0302-067003 Internal Sun Sensor
“
Specifications:
- Product Name: Internal Sun Sensor
- Function: Detects sunlight levels and automatically adjusts
shades - Compliance: CAN ICES-3(B)/NMB-3(B), FCC Part 15, ISED
licence-exempt RSS(s) - Model Number: MT02-0302-067003 FCC ID: 2AGGZ003B9ACA58 IC:
21769-003B9ACA58
Product Usage Instructions:
Safety Instructions:
Ensure to recycle batteries and damaged electrical products
properly. Do not dispose of them in general waste.
- Setting Button (P2)
- Up Button: Manually override the sensor to raise the shade
- Mode Button (M)
- Light Intensity Button (SUN)
Pairing Motor to Sensor:
To pair the motor to the sensor, hold the P1 button on the motor
head for 2 seconds. Press P2 on the sensor to complete the pairing
process.
Battery Replacement:
To change the battery, twist the back cover of the sensor
counter-clockwise to unlock it. The LED will blink every 2 minutes
when the battery is low.
Installation Considerations:
Ensure a minimum distance between the Bottom Rail/Hem Bar and
the Internal Sun Sensor to avoid contact. Follow specific
guidelines for Standard Roll and Reverse Roll installations.
Mounting Options:
- Option 1: Suction Cup
- Option 2: Adhesive Tape
FAQ:
How do I check the current sun setting on the sensor?
The factory default mode is level 1 where the sensor is
disabled. Tap the SUN button to check the current sun setting. Hold
SUN for 2 seconds to switch to the next level.
“`
Internal Sun Sensor
Detects sunlight levels and automatically adjusts your shades for enhanced comfort
and convenience.
Transmitting power: 10 mW Battery: 1.5V (AAA battery×1) Working temperature: -15°C~60°C MT02-0302-067003_v1.3_March 2025
INSTALLER
Safety Instructions
Warning: When using this product, please note the following safety precautions:
1. Do not use a different type of battery than the one specified. Doing so can cause a safety hazard. 2. Dispose or recycle used batteries according to your local rules and regulations. 3. Keep away from children. 4. If swallowed, seek medical attention immediately. 5. Do not: a) Recharge non-rechargeable batteries b) Force discharge, recharge or disassemble batteries. c) Expose batteries to temperatures exceeding the manufacturer’s specified rating. This may cause leakage or exposion, leading to burns or injury. 6. Ensure batteries are installed correctly, following indicated polarity (+ and -). 7. Do not mix old and new batteries, different brands, or different battery types (e.g., alkaline, carbon-zinc, or rechargeable). 8. If the device will not be used for an extended period, remove the batteries and store them properly. 9. Do not dispose of batteries in household trash or incinerate. Radio System Interference 10. The performance of the radio system may be affected when used near devices with strong magnetic fields or metallic surfaces. Structural conditions may also impact range and functionality. Restricted Usage Areas 11. Do not operate the radio system in areas prone to high interference, such as hospitals, airports, or other sensitive facilities.
Do not dispose of in general waste. Please recycle batteries and damaged electrical products appropriately.
CAN ICES-3(B)/NMB-3(B)
FCC & ISED Statement
MT02-0302-067003 FCC ID: 2AGGZ003B9ACA58 IC: 21769-003B9ACA58
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :
1) L’appareil ne doit pas produire de brouillage; 2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
· Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help.
Button Locations
Setting Button (P2)
Up Button
Note: The Up function can manually override the sensor to raise the shade.
Status LED Indicator
Mode Button (M)
Level LED Indicator
Light Intensity Button (SUN)
P1 Locations
P1
Internal Tubular
P1 Large Tubular
P1 P1
0.6 Cord Lift
0.8 Cord Lift
P1 Curtain
P1 Tilt Motor
Pairing Motor to Sensor
Hold P1 on motor head.
P1
2 SECS
* Internal Tubular Motor pictured. Refer to “P1 Locations” for specific devices.
Press the P1 button on the motor for 2 Seconds until the motor responds as below.
JOG
x1
Press P2 on the sensor to pair.
BEEP
x1
JOG
BEEP
x2
x3
Battery Replacement
To change the battery, twist the back cover counter-clockwise to the unlocked position.
Note: When battery is low, the LED will blink every 2 minutes.
STEP 1
STEP 2
Installation Considerations
Note: To avoid Bottom Rail/Hem Bar coming into contact with the Internal Sun Sensor, follow minimum distance to window.
Standard Roll
Reverse Roll
WINDOW WINDOW
Mounting Options
OPTION 1: SUCTION CUP
OPTION 2: ADHESIVE TAPE
Adhesive Mount
[12[1/21/616″”]] 191m9mmm [12[1/21/616″”]] 191m9mmmNote: When using the adhesive tape, it is advised to use the window protector to prevent any adhesive residue.
Suction Cup Mount
WINDOW WINDOW
Window Protector
Window
[1[1″”]] 252.54.4mmmm [1[1″”]] 252.54.4mmmmI N S TA L L E R
Pairing the Sensor using an existing Remote Control
A (Controller) = Existing controller, remote or channel that is paired to the motor
P2 Press P2 on existing controller.
Press P2 P2 again on
existing controller.
JOG
x1
B (Sensor) = Sensor to add or remove Press P2 on the sensor to pair it.
BEEP
x1
JOG
BEEP
x1
x1
Note: Repeating this section with an existing Remote on an already paired Sensor will unpair the Sensor from the motor.
JOG
BEEP
x2
x3
USER GUIDE
LIGHT LEVELS
Note: The factory default mode is level 1, the sensor is disabled. Tap SUN to check the current sun setting, Hold SUN for 2s to switch to next level.
Level
Light intensity detection range
LED
Description
1
1
Sensor is disabled
2
15K LUX
3
30K LUX
4
45K LUX
2
Light level is set to trigger command at light levels above 15K and below 30K.
3
Light level is set to trigger command at light levels above 30K and below 45K.
4
Light level is set to trigger command at light levels above 45K and below 60K.
Check light level intensity Press x1
AMBIENT LIGHT DETECTION
Press M & SUN buttons together.
M
Both level & status LED indicator lights will turn ON. The sensor will enter Ambient Light Detection.
The Light LED indicator represents the current ambient light entering the sensor.
Switch the sun level Hold
Current sun setting level is 3
2 SECS
Current sun setting level is 4
Light intensity detection range
(LUX) <15K
15K~30K
30K~45K
>45K
After 20 seconds, the indicators will turn OFF and the sensor will exit Ambient Light Detection.
LED
Description
1
Ambient light intensity is less than 15K
2
Ambient light intensity is between 15K and 30K
3
Ambient light intensity is between 30K and 45K
4
Ambient light intensity is between 45K and 60K
MODE 1
Outdoor Shades Close Mode
LED Mode Light level 1 is ON
MODE 2
Indoor Shades Open/Close Mode
For outdoor blinds, shades and roller shutters.
Use mode 1: When the shade blocks sensor.
LED Mode Light level 2 is ON
For indoor blinds and shades.
Use mode 2: When the shade does not block sensor.
USER GUIDE
When the sun intensity exceeds the set level for more than 2 minutes, the sensor will send the down command to lower the blinds or shades
When the sun intensity exceeds the set level for more than 2 minutes, the sensor will send
the down command to lower the blinds or shades.
When the sun intensity is lower than the set level for more than 15 minutes, the sensor will send the up command
to raise the blinds or shades.
CHECK MODE
Press x1 M
SWITCH MODE
Hold
2 SECS
M
MODE 3
Outdoor Shades Shade Detect Open/Close Mode
LED Mode Light level 3 is ON
For outdoor blinds, shades and roller shutters.
Use mode 3: When the shade does not block sensor.
When the sun intensity exceeds the set level for more than 2 minutes, the sensor will send
the down command to lower the blinds. Once the blinds or shades
cover the sensor, it will retract, stopping above the sensor.
Important Information: Sensor & Motor Pairing Limits
Each motor can only be paired with one sensor at a time. It is not possible to connect multiple sensors to a single motor, including any combination of, but not limited to:
Sun & Wind Sensor + Motion Sensor Internal Sun Sensor + Motion Sensor Two Sun & Wind Sensors Two Motion Sensors Two Internal Sun Sensors
If a new sensor is paired with a motor, it will override the previously paired sensor.
Multiple motors can be paired to one sensor. E.g., one Internal Sun Sensor and three motors.
When the sun intensity is lower than the set level for more than 15 minutes, the sensor will send the up command
to raise the blinds or shade.
Mode is set to 1 (LED Indicator)
Mode is set to 2 (LED Indicator)
Documents / Resources
 |
AUTOMATE MT02-0302-067003 Internal Sun Sensor [pdf] Instruction Manual MT02-0302-067003, MT02-0302-067003 Internal Sun Sensor, Internal Sun Sensor, Sun Sensor, Sensor |