Aposun SRTM LED Display DIN Rail Transducer Instruction Manual
INSTALLATION INSTRUCTION
Warning
Please do not turn on the power supply until all of the wiring is completed. Otherwise electrical shock, fire or malfunction may result. Do not wire when the power is on. Do not connect the unused terminals. Do not turn on the power supply when cleaning this instrument. Do not disassemble, repair or modify the instrument. This may cause electrical shock, fire or malfunction U s e t h i s i n s t r u m e n t i n t h e sco p e o f i t s specifications. Otherwise fire or malfunction may result.
Caution
This instrument should be installed in a domestic environment. Otherwise electrical shock, fire or malfunction may result. The operating temperature environment should between 0 (32F) to 50 (122F). To avoid using this instrument in environment full of dust or caustic gas. To avoid using this instrument in environment of strong shock or concussion. To avoid using this instrument in environment of overflow water or explosive oil. Caution Warning Output should start in about 10 seconds after power on when the instrument has control output function.
Size(units:mm)
Models
Name of parts
 |
Mark | Names | Function | |
| OUT | 1 | output lamp | output lamp | |
| (C) | 2 | indication lamp | Resistance/ temperature lamp,ON:diaplay Ω，flash: | |
| V(mV) | 3 | indication lamp | Voltage lamp ON:display V, flash:mV | |
| A(mA) | 4 | indication lamp | Current lamp ON: display A,flash:mA | |
| SET | 5 | parameter select/confirm Key | Star or stop parameter setting,change model key | |
| /RST | 6 | move key | Move key/clear key/RST key | |
| 7 | Up Key | Parameter Up Key | ||
| 8 | Down Key | Parameter Down Key | ||
Connection Drawing
Attention: pleasse subject to the diagram on the product if any changes.
|
DC voltage/current |
AC voltage/current | PT100 |
TC |
 |
 |
 |
Parameter setting
Operation process
Power ON
LED ON
Display input model(V)
Display measure low range
High range
Start
Analogue setting Example:4～20 display -50℃～200℃
Press SET key＞3S, found
Continue Press SET key
Press RST key 3 times let the 3 flash it.
Perss Down key decrease setting value
Press SET key input setting value
Press SET key found
Press RST key 4 times let the 4 flash it
Perss Up key increase setting value Press SET key input setting value
Clear zero
Specifications
| Power supply | AC/DC 90-260V 50/60Hz (specific order AC/DC 24V) |
| Consumption | |
| Accuracy | |
| Sampling rate | ≤8 times / second. |
| Display range | -1999～9999 |
| Overflow display | UUUU |
| Analogue output | 0-5V、0-10V、1-5V、2-10V、4-20mA、0-20mA by select one.default:4-20mA. |
| Installation model | 35mm |
| Size | 120（L）×55（W）×75（H）mm |
| Weight | Abt 205g |
| Environment temperature | -10-50℃ 35-85% humidity |
| Specification | |
| DC voltage | 0-2V、0-20V、0-200V、0-600V |
| AC voltage | 0-2V、0-20V、0-200V、0-600V |
| DC current | 0-200mA、0-2A、0-5A、0-20A |
| AC current | 0-200mA、0-2A、0-5A、0-20A |
| Thermocouple (TC) | B：600-1700℃ |
| S：0-1700℃ | |
| R：500-1600℃ | |
| T：0-400℃ | |
| E：0-1000℃ | |
| J：0-1200℃ | |
| K：0-1200℃ | |
| RTD | Pt100：-200～600℃ |
| Line resistance | 0-400Ω |
Documents / Resources
 |
Aposun SRTM LED Display DIN Rail Transducer [pdf] Instruction Manual SRTM LED Display DIN Rail Transducer, SRTM, LED Display DIN Rail Transducer, Display DIN Rail Transducer, DIN Rail Transducer |
