Contents hide
1 Alfred DB2S Smart Locks
2 Product Usage Instructions
3 Engineering Specification
4 INTERFACES & ACCESSORIES
5 FEATURES & SPECIFICATIONS
6 PRODUCT QUICK START
7 SOFTWARE FUNCTION DEFINITION
8 FAQ
9 Documents / Resources
9.1 References

Alfred-logo

Alfred DB2S Smart Locks

Alfred-DB2S-Smart-Locks-product

Specifications

FEATURES & SPECIFICATIONS

Structural Characteristics

  • Product Identifier: DB2S
  • Color: Black
  • Shell Material: Kirsite
  • Operating Temperature: -25°C to 55°C
  • Relative Humidity: 20-80%

Hardware Characteristics

  • Module: EFR32ZG23A010F512GM40
  • TX Power: Max 14dBm
  • Antenna Distance: 40m (Indoor) / 150m (Outdoor)
  • Indicator Light Color: 1 red, 1 green, 1 low battery, 1 door indicator
  • Input Voltage: 4.7~5.5V
  • Battery Info: Lithium-Ion battery
  • Working Current: Module – 10mA (Wake Up), 40mA Send message; Door Lock body – 52mA (Wake Up), 190mA operate door lock
  • Standby Current: Module – 25uA; Door Lock body – 170uA

Software Characteristics

    • Wireless Technology
    • Certification Type
    • SDK Version: 7.18.4
    • Library Type: Enhanced 232 Slave
    • Role Type: ZWAVEPLUS_INFO_REPORT_ROLE_TYPE_SLAVE_SLEEPING_LISTENING (0x07)

Product Usage Instructions

PRODUCT QUICK START

Important Safety Information

  • Before using the product, carefully read through the safety information provided in the manual to ensure safe operation.

About Z-Wave

  • The product operates on Z-Wave technology. Make sure to familiarize yourself with Z-Wave functionality for optimal usage.

About SmartStart

  • SmartStart enables easy inclusion of the product into a Z-Wave network by scanning the Z-Wave QR Code with a compatible controller. The product will be automatically added within 10 minutes of being switched on near the network.

Engineering Specification

 

Document No.

  

SPEC-DB2S
 

Version

  

1.0
Description This document mainly introduces the new generation Alfred Door Lock – ML2. The content mainly includes its interfaces, accessories, features, specifications, quick start, and software function definition.

 

 

This device must be used in conjunction with a security enabled Z-Wave® controller in order to fully utilize all implemented functions. This product can be operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.
 

Written By

  
 

Date

  
 

Reviewed By

  
 

Date

  
 

Approved By

  
 

Date

  

INTERFACES & ACCESSORIES

Alfred-DB2S-Smart-Locks-fig-1

Terminology Description
Touch screen keypad Used to operate various functions of the door lock
Indicator light Status indicator #1

Status indicator #1 Low battery indicator

Identify indicator
Speaker For voice prompts
Main power supply interface Lithium-Ion battery
Backup power supply interface USB-C interface power supply
Button Reset button

 Multi-function button
Thumb turn For manual lock / unlock operation
Handing Switches Used to set the “rotation direction when the Thumb turn is locked”

FEATURES & SPECIFICATIONS

Structural Characteristics

Parameter Value
Product Identifier DB2S
Color black
Shell Material kirsite
Shell Fire-proof Level Frosting
Usage For indoor use.
Operating Temperature -25-55℃
Relative Humidity 20-80%

Hardware Characteristics

Parameter Value
Module EFR32ZG23A010F512GM40
TX Power Max: 14dBm
Antenna Distance 40m (Indoor) /150m (Outdoor)
Indicator Light Color 1 red, 1 green, 1 low battery, 1 door indicator.
Input Voltage 4.7~5.5V
Battery Info Lithium-Ion battery
Working Current Module: 10mA(Wake Up), 40mA（Send message）

 Door Lock body: 52mA(Wake Up), 190mA（operate door lock）
Standby Current Module: 25uA

 Door Lock body: 170uA

Software Characteristics

Parameter Value
Wireless Technology Z-Wave®
Certification Type Z-Wave Plus® V2
SDK Version 7.18.4
Library Type Enhanced 232 Slave
Role Type ZWAVEPLUS_INFO_REPORT_ROLE_TYPE_SLAVE_SLEEPING_LISTENING (0x07)
Generic Device Type GENERIC_TYPE_ENTRY_CONTROL (0x40)
Specific Device Type SPECIFIC_TYPE_DOOR_LOCK (0x01)
Security Class Non-Security, S0, S2-ACCESS
SmartStart Support. After powering on, SmartStart is auto active if it’s out of the network.
Over The Air （OTA） Support. Firmware can be updated via RF.
Multichannel Device No
Association Support. Refer to Section 4.7 Association Group Info.
Factory Reset Support. Refer to Section 3.6 How to factory reset.
Power-down Memory Support. All command settings will stay unchanged even power down.
Timed battery report Support. Refer to Configuration Parameter 3.
Low battery warning Support.
Door State Report Support. When door lock mode changed, send out notification via Group 1.
User code Report Support. When user code changed, send out notification via Group 1.

PRODUCT QUICK START

Important safety information

Please read this Engineering Specification carefully for correct and effective use.

Failure to follow the recommendations set forth by Alfred Limited may be dangerous or cause a violation of the law. The manufacturer, importer, distributor, and/or reseller will not be held responsible for any loss or damage resulting from not following any instruction in this guide or in other materials.

The product is intended for indoor use in dry locations only. Do not use in damp, moist, and /or wet locations.

About Z-Wave

  • Z-Wave is the international wireless protocol for communication in the Smart Home.
  • Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
  • This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
  • If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
  • This device can be operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers. All mains operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.
  • This device is a security enabled Z‐Wave Plus product that is able to use encrypted Z‐Wave Plus messages to communicate to other security enabled Z‐Wave Plus products. S2 Security Enabled Controller is required to operate the device.

About SmartStart

Smart Start enabled products can be added into a Z-Wave network by scanning the Z-Wave QR Code present on the product with a controller providing SmartStart inclusion. No further action is required and the SmartStart product will be added automatically within 10 minutes of being switched on in the network vicinity.

How to add the product into Z-Wave network

  1. Follow the user guide of hub to enter inclusion mode.
  2. Operate on lock following guide below:
    1. Enter master mode (** + Master PIN Code + √)
    2. Input “8” to enter “function extension settings”
    3. Input “1” to enter “Include mode”

How to remove the product from Z-Wave network

  1. Follow the user guide of hub to enter exclusion mode.
  2. Operate on lock following guide below:
    1. Enter master mode (** + Master PIN Code + √)
    2. Input “8” to enter “function extension settings”
    3. Input “2” to enter “Exclusion mode”

How to factory reset

  1. Operations on lock
    1. Open the door and keep the lock in “unlock” status.
    2. Open battery box and find the reset button.
    3. Use a sharp thing to press and hold the reset button
    4. Keep holding the reset button and remove the battery from battery box then replace it.
    5. Keep holding the reset button down until you hear the lock beep (Can take up to 10 seconds).
  2. Please use this procedure only when the network primary controller is missing or otherwise inoperable.
  3. Default master pin code is “12345678”, please modify it after reset (Refer to programming instruction).

Z-Wave DSK Location

  • You can find the QR code when you open the battery box
  • You may also find the QR Code and DSK on individual package of each product.
  • Please do not remove or damage them.

SOFTWARE FUNCTION DEFINITION

User Behavior Interaction

User behavior Out of the network In the network
Power on Key panel light is on

 The unlocking indicator light or locking indicator light is on Send Inclusion Requests for SmartStart

 Key panel light is on

 The unlocking indicator light or locking indicator light is on
Inclusion network Enter master mode (** + Master PIN Code + √) Input “8” to enter “function extension settings” Input “1” to enter “Inclusion mode” NA
Exclusion network NA Enter master mode (** + Master PIN Code +

√)

Input “8” to enter “function extension settings” Input “2” to enter “Exclusion mode”
unlock The green indicator lights up for 3 seconds The green indicator lights up for 3 seconds Send Notification Report and Door Lock Operation Report to association group
Lock The red indicator lights up for 3 seconds The red indicator lights up for 3 seconds

Send Notification Report and Door Lock Operation Report to association group
User code (Add/delete/modify) NA Send Notification Report and User code Report to association group

Supported Command Classes

Command Class Version Not added Non-secure added Securely 0 added Securely 2 added
Non-secure CC Secure CC Non-secure CC Secure CC
ZWAVEPLUS_INFO 2 Support Support Support   Support  
ASSOCIATION 2       Support   Support
ASSOCIATION_GRP_INFO 3       Support   Support
Multichannel Association 3       Support   Support
NOTIFICATION 8       Support   Support
Door Lock 4       Support   Support
User Code 2       Support   Support
Schedule Command Class 4       Support   Support
Door Lock Logging 1       Support   Support
Configuration 4       Support   Support
Application Status 1 Support Support Support   Support  
Time 1 Support Support Support   Support  
Time Parameters 1       Support   Support
VERSION 3       Support   Support
MANUFACTURER_SPECIFIC 2       Support   Support
DEVICE_RESET_LOCALLY 1       Support   Support
POWERLEVEL 1       Support   Support
Indicator 3       Support   Support
BATTERY 1       Support   Support
SECURITY 1 Support Support Support   Support  
SECURITY_2 1 Support Support Support   Support  
TRANSPORT_SERVICE 2 Support Support Support   Support  
SUPERVISION 1 Support Support Support   Support  
FIRMWARE_UPDATE_MD 5       Support   Support
Language 1       Support   Support

Basic Command Class mapping

Basic Command maps to Door Lock Command Class, as shown below.

Command Value Mapped Value Function
Basic Set 0x00 Door Lock Operation Set Door Unsecured Open the door
0xFF Door Secured Close the door
Basic Report 0x00 Door Lock Operation Report Door Unsecured The door is opened
0xFF Door Secured The door is closed
Basic Get   Door Lock Operation Get    

Z-Wave Plus Info

Parameter Value
Version 2
Role Type 7 (ZWAVEPLUS_INFO_REPORT_ROLE_TYPE_SLAVE_SLEEPING_LISTENING)

(APPLICATION_FREQ_LISTENING_MODE_1000ms)
Node Type 0 (ZWAVEPLUS_INFO_REPORT_NODE_TYPE_ZWAVEPLUS_NODE)
Installer Icon Type 0x0300 (ICON_TYPE_GENERIC_DOOR_LOCK_KEYPAD)
User Icon Type 0x0300 (ICON_TYPE_GENERIC_DOOR_LOCK_KEYPAD)

Manufacturer Specific

The Command is used to advertise manufacturer specific information.

Parameter Value
Manufacturer ID 1 0x04
Manufacturer ID 2 0x65
Product Type ID 1 0x01
Product Type ID 2 0x03
Product ID 1 0x00
Product ID 2 0x04(DB2S)

Version

The Command may be used to obtain the Z-Wave library type, the Z-Wave protocol version used by the application, the individual command class versions used by the application.

Parameter Value
Protocol Library Type 0x03
Protocol Version 0x07
Protocol Sub Version 0x12
Firmware 0 Version Main Chip Firmware Version Major
Firmware 0 Sub Version Main Chip Firmware Version Minor
Hardware Version 0x04(DB2S)
Number of firmware targets 0x01
Firmware 1 Version Door Lock Firmware Version Major
Firmware 1 Sub Version Door Lock Firmware Version Minor

Association Group Info

The Command is used to manage associations to Node ID destinations.

ID Name Count Profile Function
1 Lifeline 5 General: Lifeline

(0x0001)

 Device Reset Locally Notification (0x5A01) ：

Issued when Factory Reset is performed. Battery Report(0x8003)：

Issued periodically to report the current battery level; Issued when battery becomes low.

Door Lock Operation Report(0x6203)： Issued when door lock mode changed Notification Report(0x7105)：

Issued when door lock event changed User Code Report(0x6303)：

Issued when user code changed by keypad Master Code Report(0x6310)

Issued when master code changed by keypad User Code Keypad Mode Report(0x630A) Issued when keypad mode changed by keypad Configuration Report(0x7006)

Issued when the volume configuration value is changed by keypad

Indicator Report(0x8703)：

Issued when indicator set received.
 

2

  

On/Off control

  

5

 General: Control

(0x2000)

 Basic Set (0x2001) ：

Issued when door lock mode changed (value is determined by parameter 0x04)

Notification

The Command is used to advertise events or states, such.

Notification Type = Access Control (0x06)，according to Table 4-8-1

Notification Type = Home Security (0x07)，according to Table 4-8-2

Table 4-8-1:

Description Event Alarm type Alarm Level Parameters
Manual lock operation (mechanical key or thumb turn) 0x01 0x15 0x01  
Manual unlock operation (mechanical key or thumb turn) 0x02 0x16 0x01  
RF lock operation 0x03 0x18 0x01  
RF unlock operation 0x04 0x19 0x01  
Keypad lock operation 0x05 0x15 0x02  
Keypad unlock operation 0x06 0x13 User ID User Code Report
0xFB Master Code Report
Auto lock locked operation 0x09 0x1B 0x01  
Lock jammed 0x0B 0x00 0x00  
All user codes deleted 0x0C 0x21 0xFF  
Single user code deleted 0x0D 0x21 User Id User Code Report
New user code added (add and modify) 0x0E 0x70 User Id User Code Report
0xFB Master Code Report
New user code not added due to duplicate code 0x0F 0x71 User Id User Code Report
  0xFB Master Code Report
New program code entered : unique code for lock configuration 0x12 0x70 0x00 Master Code Report
Manually enter user access code exceeds code limit 0x13 0x00 0x00  
Door opened 0x16 0x00 0x00  
Door closed 0x17 0x00 0x00  

Table 4-8-2:

Description Notification Event Alarm type Alarm Level Parameters
Tampering Product covering removed

(front escutcheon removed from door)

 0x03 0x00 0x00  

Door Lock

The Command is used to operate and configure a door lock device.

  1. Support Door Lock Mode: Door Secured (0xFF), Door Unsecured (0x00)
  2. Door Lock Capabilities Report Command:
    1. Supported Operation type Bit Mask Length = 0x01
    2. Supported Operation Type Bit Mask 1 = 0x02 (Constant operation)
    3. Supported Door Lock Mode List Length = 0x02
    4. Supported Door Lock Mode 1 = 0x00 (Door Unsecured)
    5. Supported Door Lock Mode 2 = 0xFF (Door Secured)
    6. Supported Outside Handle Modes Bitmask = 0x00
    7. Supported Inside Handle Modes Bitmask = 0x00 (No Handle)
    8. Supported door components = 0x03 (Bolt & Door)
    9. ARS = 1
    10. HRS = TAS = BTBS = 0
  3. Door Lock Operation Set Command:
    1. Door Unsecured (0x00)
    2. Door Secured (0xFF)
  4. Door Lock Operation Report Command:
    1. Door Unsecure, example: 00 01 02 FE FE 00 00
      • Door Lock Mode = 0x00 (Door Unsecured)
      • Outside Door Handles Mode = 0 (Disabled), Inside Door Handles Mode = 1 (Handle 1 = Enable) Door Condition = 2 (Bolt Unlocked, Door Open)
      • Lock Timeout minutes = 0xFE (No unlocked period)
      • Lock Timeout Seconds = 0xFE (No unlocked period)
      • Target Door Lock Mode = 0x00 (Door Unsecured)
      • Duration = 0x00
    2. Door Secured, example: FF 01 01 FE FE FF 00
      • Door Lock Mode = 0xff (Door secured)
      • Outside Door Handles Mode = 0 (Disabled), Inside Door Handles Mode = 1 (Handle 1 = Enable) Door Condition = 1 (Bolt Locked, Door Closed)
      • Lock Timeout minutes = 0xFE (No unlocked period)
      • Lock Timeout Seconds = 0xFE (No unlocked period)
      • Target Door Lock Mode = 0x00 (Door Unsecured)
      • Duration = 0x00
  5. Door Lock Configuration Report Command:
    1. Operation Type = 0x01 (Constant operation)
    2. Supported Door Lock Mode 1 = 0x00 (Door Unsecured)
    3. Supported Door Lock Mode 2 = 0xFF (Door Secured)
    4. Lock Timeout minutes = 0xFE (No unlocked period)
    5. Lock Timeout Seconds = 0xFE (No unlocked period)
    6. Auto-relock time 1 = 0
    7. Auto-relock time 2 = 0
    8. Hold and release time 1 = 0x00
    9. Hold and release time 2 = 0x00
    10. BTB = TA = 0

The auto relock time mapping table of door lock and Z-Wave is as follows:

Z-Wave definition Door lock function
Auto-relock time = 0 disabled
Auto-relock time = 1 – 30 30 Seconds
Auto-relock time = 31 – 60 60 Seconds
Auto-relock time = 61 – 120 120 Seconds
Auto-relock time = 120 – 65535 180 Seconds

Door Lock Logging

The Command provides an audit trail in an access control application. Each time an event takes place at the door lock, the system logs the user’s ID, date, time etc.

  • Max records stored = 250

User Code

The Command is used to manage User Codes in access control systems

  1. Support users: 250
  2. Support master code
  3. Supported User ID Status: available(0x00), enabled/grant access (0x01)
  4. Supported Keypad Modes: Normal mode, Vacation mode, Privacy mode
    • In Privacy mode, it will ignore Door Lock Operator Set Command, and will send Application Rejected Request.
  5. User Code Capabilities Report Command:
    1. Supported Users = 250
    2. MC (Master Code) Support = 1
    3. MCD (Master Code Deactivation) Support = 0
    4. UCC (User Code Checksum) Support = 0
    5. MUCR (Multiple User Code Report) Support = 0
    6. MUCS (Multiple User Code Set) Support = 0
    7. Supported User ID Status Bit Mask Length = 1
    8. Supported User ID Status Bit Mask 1 = 0x03 (Available & Enabled/Grant Access)
    9. Supported Keypad Modes Bit Mask Length = 1
    10. Supported Keypad Modes Bit Mask 1 = 0x07 (Normal mode, Privacy mode, Locked Out mode)
    11. Supported Keys Bit Mask Length = 8
    12. Supported Keys Bit Mask 1 = 0x00
    13. Supported Keys Bit Mask 2 = 0x00
    14. Supported Keys Bit Mask 3 = 0x00
    15. Supported Keys Bit Mask 4 = 0x00
    16. Supported Keys Bit Mask 5 = 0x00
    17. Supported Keys Bit Mask 6 = 0x00
    18. Supported Keys Bit Mask 7 = 0xFF (digits 0-7)
    19. Supported Keys Bit Mask 8 = 0x03 (digits 8-9)

Schedule

The Command allows scheduling the execution of commands for a given duration in a supporting device. It is a generic Command Class that may be used to schedule commands of any other Command Class.

  1. 1. SCHEDULE_SUPPORTED_REPORT:
    1. Number of Supported Schedule IDs: 10
    2. Support Enable/disable: 0
    3. Fall-back Support: 0
    4. Start Time Support: 1
    5. Number of supported CC: 1
    6. Supported CC 1: USER_CODE_COMMAND_CLASS
    7. Supported Command1: 0x01 (Only Set Commands are supported)
    8. Override Support: 0
    9. Supported Override Types: 0
    10. Number of Supported Schedule Blocks: 1
  2. SCHEDULE_SUPPORTED_COMMANDS_REPORT：
    1. Supported Command Class: USER_CODE_COMMAND_CLASS
    2. Supported Command: USER_CODE_SET

Battery

The Command is used to request and report battery levels for a given device.

  1. If send Battery Get to the device, it will issue Battery Report with current battery level to the requester.
  2. If re-power on, it will issue Battery Report with current battery level via Lifeline.
  3. If waked up, it will detect battery level, and issue Battery Report (Value=0xFF) via Lifeline when battery level is less than 20%.
  4. Support timed battery report, refer to Configuration Parameter 3.

Language

The Command is used to specify the language settings on a device.

  1. The supported languages are as follows
    1. English (eng)
    2. Spanish (spa)
    3. Portuguese (por)
    4. French (fre, fra)

Indicator

The Command is used to help end users to monitor the operation or condition of the application provided by a supporting node.

Indicator ID Property ID
Node Identify 0x50 On Off Period 0x03
On Off Cycles 0x04
On time within an On/Off period 0x05

Time

  • The Command is used to read date and time from a supporting node in a Z-Wave network.

Time Parameters

  • The Command is used to set date and time in a device hosting this facility

Configuration

The Command allows product specific configuration parameters to be changed.

Note: No Bulk Support equals to True. It will return an Application Rejected Request Command when receiving Configuration Bulk Set or Get (if received without Supervision encapsulation). It will reset all its configuration parameters if either manually reset to factory default or receives a Configuration Default Reset Command. It will NOT modify or reset any configuration parameter when being included or excluded of a Z-Wave network.

Parameter 0x01 (1)
Name Configure volume level
Info Configure volume level
Properties Size 1 Min Value 0
Format Unsigned Integer Max Value 2
Read-only False Default Value 2
Altering capabilities False Advanced False
Description Configure volume level
  Value Function
0 silent
1 Low volume
2 High volume
Parameter 0x02 (2)
Name Configure led
Info Enable/disable led
Properties Size 1 Min Value 0
Format Unsigned Integer Max Value 1
Read-only False Default Value 1
Altering capabilities False Advanced False
Description LED on the inside of the product.
Value Function
0 OFF
1 ON (blink)
Parameter 0x03 (3)
Name Timed battery report
Info Configure timed battery report
Properties Size 2 Min Value 0
Format Unsigned Integer Max Value 14400(0x3840)

 

(10 days)
Read-only False Default Value 1440(0x05A0)

 

(one day)
Altering capabilities False Advanced False
Description Enable/Disable timed battery report and sets how often battery is reported in minutes.
Value Function
0 Disable timed battery report
1-14400 Enable timed battery report and sets how often battery is reported in minutes.
Parameter 0x04 (4)
Name Association Group 2 Settings
Info Configure the Basic Set value
Properties Size 1 Min Value 0
Format Unsigned Integer Max Value 6
Read-only False Default Value 1
Altering capabilities False Advanced False
Description Determine the Basic Set value to control other Z-Wave devices directly.
Value Function
0 Disable completely.
1 Unlocked Status sends Basic SET 0xFF, Locked Status sends Basic SET 0x00.
2 Unlocked Status sends Basic SET 0x00, Locked Status sends Basic Set 0xFF.
3 Sends only Basic SET 0xFF when Unlocked Status happens.
4 Sends only Basic SET 0x00 when Locked Status happens.
5 Sends only Basic SET 0x00 when Unlocked Status happens.
6 Sends only Basic SET 0xFF when Locked Status happens.

FAQ

  • Q: How do I perform a factory reset on the product?
    • A: To perform a factory reset, refer to Section 3.6 in the manual for detailed instructions on resetting the product to its default settings.

Documents / Resources

Alfred DB2S Smart Locks [pdf] Instruction Manual
DB2S, DB2S Smart Locks, Smart Locks, Locks

References

Leave a comment

Your email address will not be published. Required fields are marked *