DDBC1200 Dynalite Signal Dimmer Controller
“
Specifications:
- Model: DDBC1200
- Product Name: Signal Dimmer Controller
- Dimensions: 103 mm (4.06 in) x 93 mm (3.66 in) x 215 mm (8.46
in) - Control Channels: 12
- Protocol Options: 0-10 V, DALI Broadcast
- Input Voltage: 100-277 V
- Current Rating: 0.5 A
Product Usage Instructions:
Installation:
Devices must be installed in an approved enclosure by a
qualified electrician following all national and local electrical
and construction codes and regulations.
Programming:
- Enter program mode by holding the corresponding channel button
for 4 seconds. - Select the desired protocol by cycling through options using
the channel buttons (0-10 V or DALI Broadcast). - Exit program mode by quickly pressing the same channel button
once.
Safety Instructions:
When using the product, follow these safety precautions:
- Do not use the equipment outdoors.
- Use the equipment only for its intended purpose.
- Read and follow all safety instructions provided in the
manual.
FAQ:
Q: What are the voltage and current specifications of the
Signal Dimmer Controller?
A: The input voltage range is 100-277 V with a current rating of
0.5 A.
Q: How many control channels does the controller support?
A: The controller supports 12 control channels.
Q: How do I program the Signal Dimmer Controller?
A: To program the controller, follow the steps outlined in the
user manual under the “Programming” section.
“`
DDBC1200
Signal Dimmer Controller
Installation Instructions
Instructions d’installation Installationsanweisungen Instrucciones de instalación Istruzioni per l’installazione Installatie-instructies
Devices must be installed in an
approved enclosure by a qualified electrician in accordance with all
national and local electrical and
construction codes and regulations.
Les appareils doivent être installés dans un lieu jugé apte, par un électricien qualifié et conformément aux règles et normes locales et nationales en matière d’électricité et de construction.
Die Geräte müssen von einem geprüften Elektriker entsprechend allen nationalen und lokalen Elektro und Bauvorschriften in einem zugelassenen Gehäuse installiert werden.
Los dispositivos se deben instalar en un recinto aprobado por un electricista cualificado de acuerdo a todos los reglamentos eléctricos y de construcción locales y nacionales pertinentes.
I dispositivi devono essere installati da un elettricista qualificato in un luogo approvato, in conformità a tutti gli standard e le norme nazionali e locali vigenti in materia di impianti elettrici e costruzioni edilizie.
Apparaten moeten door een erkende elektricien worden geïnstalleerd in een goedgekeurde behuizing in overeenstemming met alle nationale en lokale elektriciteits en bouwvoorschriften en wetgeving.
/
103 mm (4.06 in) 93 mm (3.66 in)
123456789
1
IEC Pollution Degree II
RJ12
215 mm (8.46 in)
64 mm (2.52 in)
45 mm (1.77 in)
50° C (122° F) 0° C (32° F)
90%
45 mm (1.77 in)
2 Control Channel Ratings
DALI Broadcast
80/CH Guaranteed 160 mA Maximum 250 mA
Insulation: basic
0-10 V
Sink / Source 50 mA CHs: 1-12
Sink / Source 100 mA CHs: 2, 4, 6, 8, 10, 12 0 mA CHs: 1, 3, 5, 7, 9, 11
300
Driver dependent
3
5 mm2 10+ AWG
0.6 Nm 5.5 Lb-in
DALI / 0-10 V
N L DA- DA+ DA- DA+ DA- DA+ DA- DA+ DA- DA+ DA- DA+ DA- DA+ DA- DA+ DA- DA+ DA- DA+ DA- DA+ DA- DA+
SUPPLY
CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9 CH10 CH11 CH12
1
2
3
4
5
6
7
8
9
10
11
12
1. Enter program mode
(4 secs)
1
2
3
4
5
6
7
8
9
10
11
12
2. Select protocol
= 0 – 10 V = DALI Broadcast
3. Exit program mode
(1 sec)
1
2
3
4
5
6
7
8
9
10
11
12
4
FELV / Class 2, suitable for Class 1 wiring (UL)
100-277 V 0.5 A
CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 CH9 CH10 CH11 CH12
N L DA- DA+ DA- DA+ DA- DA+ DA- DA+ DA- DA+ DA- DA+ DA- DA+ DA- DA+ DA- DA+ DA- DA+ DA- DA+ DA- DA+
DALI / 0-10 V DALI / 0-10 V DALI / 0-10 V DALI / 0-10 V DALI / 0-10 V DALI / 0-10 V DALI / 0-10 V DALI / 0-10 V DALI / 0-10 V DALI / 0-10 V DALI / 0-10 V DALI / 0-10 V
µP
IEC Overvoltage Category III 2
SHLD GND
D+ D+12 V AUX/ UL924
RS-485 DyNet/DMX512 Rx SELV/Class 2 (UL)
12 V
300 mA
5
SHLD GND D+ D+12 V AUX/ UL924
0.3-2.5 mm2 22-12 AWG
0.4 Nm 3.5 Lb-in
GND AUX/UL924 < 20 m (65 ft)
2 A RS-485 DyNet
6
RS-485 DyNet
7
3
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should always be followed including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
a) Do not use outdoors b) Do not use this equipment for other than the intended use.
SAVE THESE INSTRUCTIONS
Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Any modifications not approved by the manufacturer of this device could void the user’s authority to operate this device.
This Class B digital apparatus complies with Canadian ICES-003: CAN ICES-3(B)/NMB-3(B). Cet appareil numerique de la Classe B est conforme a la norme NMB-003 du Canada: CAN ICES-3(B)/NMB-3(B).
Installation of a home and building automation and control system shall comply with IEC 60364 (all parts). The temperature limits and current-carrying capacities for the communication wires specified in IEC 60364-5-52 shall not be exceeded.
© 2024 Signify Holding. All rights reserved. Specifications are subject to change without notice. No representation or warranty as to the accuracy or
completeness of the information included herein is given and any liability for any action in reliance thereon is disclaimed. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. All other trademarks are owned by Signify Holding or their respective owners.
www.dynalite.com
AZZ 370 08 24 R22
Documents / Resources
 |
PHILIPS DDBC1200 Dynalite Signal Dimmer Controller [pdf] Installation Guide DDBC1200, DDBC1200 Dynalite Signal Dimmer Controller, Dynalite Signal Dimmer Controller, Signal Dimmer Controller, Dimmer Controller, Controller |