Chii chinonzi Z-Wave?

Z-Wave ndiyo yepasirese isina waya protocol yekutaurirana muSmart Home. Izvi
mudziyo wakakodzera kushandiswa munharaunda yakataurwa muchikamu che Quickstart.

Z-Wave inovimbisa kutaurirana kwakavimbika nekusimbisa meseji yese (nzira mbiri
kutaurirana) uye ese mains powered node anogona kuita seanodzokorora mamwe ma node
(meshed network) kana iyo inogamuchira isiri yakananga isina waya renji ye
transmitter.

Ichi chishandiso uye chimwe nechimwe chakasimbiswa Z-Wave chishandiso chinogona kuva kushandiswa pamwe chete nezvimwe
yakasimbiswa Z-Wave mudziyo zvisinei nerudzi uye kwaakabva chero bedzi ari maviri akakodzera kune
zvakafanana frequency range.

Kana mudziyo unotsigira kukurukurirana kwakachengeteka ichataurirana nemimwe michina
yakachengeteka chero bedzi chigadziro ichi chinopa imwechete kana yakakwirira yehutano.
Zvikasadaro zvinongoerekana zvashanduka kuita yakaderera mwero wekuchengetedza kuchengetedza
kumashure kugarisana.

Kuti uwane rumwe ruzivo nezve Z-Wave tekinoroji, zvishandiso, machena mapepa nezvimwe ndapota tarisa
kune www.z-wave.info.

Product Description

Iyo Yakachengeteka SSP 301 inochinja uye inodzokorora inoumba chikamu cheZ-Wave Plus kumba otomatiki network. Iyo SSP 301 mudziyo une mains powered neEU plug type, inochinja (simba On/Off) mudziyo wakabatana kungave neZ-Wave network kana nemaoko nekudzvanya bhatani rayo rakabatanidzwa. -Wave network nekubatsira mameseji kubva kune mamwe maturusi kusvika kune kwaanosvika.

Gadzirira Kuisa / Reset

Ndapota verenga bhuku rekushandisa usati waisa chigadzirwa.

Kuti ubatanidze (wedzera) mudziyo weZ-Wave kune network inofanira kunge iri mufekitari default
state. Ndokumbirawo muve nechokwadi chekuseta zvakare mudziyo mufekitari default. Unogona kuita izvi ne
kuita basa reKusabatanidzwa sezvinotsanangurwa pazasi mubhuku rekushandisa. Yese Z-Wave
controller inokwanisa kuita oparesheni iyi asi zvinokurudzirwa kushandisa yekutanga
mutongi weiyo yapfuura network kuti ave nechokwadi chekuti mudziyo wacho hauna kubatanidzwa nemazvo
kubva kune network iyi.

Dzorera kufekitari default

Ichi chishandiso chinobvumirawo kusetwa patsva pasina kubatanidzwa kweZ-Wave controller. Izvi
nzira inofanirwa kushandiswa chete kana iyo yekutanga controller isingashande.

Ndapota shandisa maitiro aya chete kana iyo yekutanga controller isipo kana neimwe nzira isingashande, Simba kutenderera mudziyo, dzvanya uye bata bhatani kwemasekonzi 7-11 mukati memasekonzi makumi matanhatu emagetsi kutenderera kuisa mudziyo mufekitari default. Iyo inogadzirisa zvese zvigadziriso uye kushamwaridzana kune fekitori default. Iyo zvakare inobvisa chishandiso kubva kuZ-Wave network.

Yambiro Yekuchengetedza yeMains Powered Devices

CHENJERA: vanotenderwa matekiniki chete vari pasi pekutariswa kwenyika-yakananga
kumisikidza nhungamiro/maitiro anogona kuita mabasa ane mains simba. Pamberi pegungano re
chigadzirwa, voltage network inofanirwa kudzimwa uye kuve nechokwadi kuti isachinjisa zvakare.

Kubatanidzwa/Kusabatanidzwa

Pafekitori default mudziyo hausi weZ-Wave network. Chishandiso chinoda
kuva yakawedzerwa kune iripo isina waya network kutaurirana nemidziyo yetiweki iyi.
Iyi nzira inodaidzwa Kubatanidzwa.

Midziyo inogona zvakare kubviswa kubva kunetiweki. Iyi nzira inodaidzwa Kusabatanidzwa.
Maitiro ese ari maviri anotangwa neyekutanga controller yeZ-Wave network. Izvi
controller inoshandurwa kuita yekusabatanidzwa inoenderana inclusion mode. Kubatanidzwa uye Kusabatanidzwa ndiko
obva aita kuita yakakosha yemanyorero chiito pamudziyo.

Kubatanidzwa

Kuti ubatanidze iyo SSP 301 panetiweki, isa mutongi mune yekusanganisa modhi. Zvino dzvanya uye ubate bhatani paSSP 301 kwemasekonzi mana kusvika manomwe wobva waburitswa. Iyo netiweki mamiriro LED ichatanga kupenya (kaviri pasekondi) pakubudirira kwekutanga kwekubatanidzwa maitiro. Pakubatanidzwa kwakabudirira LED inodzima.

Kusabatanidzwa

Kusabvisa iyo SSP 301 kubva kunetiweki, isa mutongi mune yekusabvisa modhi. Zvino dzvanya uye ubate bhatani paSSP 301 kwemasekonzi mana kusvika manomwe wobva waburitswa. Mushure mekubudirira kusarudzika iyo network network LED ichatanga kupenya kamwe pasekondi, uye mudziyo unozodzokera kufekitori default.

Kukurukurirana kumudziyo wekurara (Wakeup)

Chishandiso ichi chinoshandiswa nebhatiri uye chinoshandurwa kuita hope dzakadzika nguva zhinji
kuchengetedza hupenyu hwebhatiri nguva. Kukurukurirana nemudziyo kunogumira. Kuti uzo
kutaurirana nemudziyo, static controller C inodiwa mumambure.
Mutongi uyu anochengetedza bhokisi retsamba remidziyo inoshandiswa nebhatiri uye chitoro
mirairo isingagamuchirwe panguva yehope huru. Pasina mutongi akadaro,
kutaurirana kunogona kuve kusingaite uye / kana hupenyu hwebhatiri nguva yakanyanya
yakaderera.

Chishandiso ichi chinomuka nguva nenguva uye kuzivisa kumuka
state nekutumira inonzi Wakeup Notification. Mutongi anogona ipapo
bvisa bhokisi retsamba. Nokudaro, chigadziro chinoda kugadziriswa nezvinodiwa
nguva yekumuka uye node ID yemutongi. Kana mudziyo wakabatanidzwa ne
a static controller uyu controller anowanzo kuita zvese zvinodiwa
configurations. Nguva yekumuka ndeye tradeoff pakati pemaximal bhatiri
nguva yehupenyu uye mhinduro dzinodiwa dzechigadzirwa. Kuti umutse mudziyo ndapota ita
chiito chinotevera:

NA

Kukurumidza dambudziko kupfura

Heano mashoma mazano ekuisa network kana zvinhu zvikasashanda sezvaitarisirwa.

1. Ita shuwa kuti mudziyo uri mufekitori reset mamiriro usati wasanganisira. Mukupokana usabvisa pamberi sanganisira.
2. Kana kusanganisirwa kuchiri kutadza, tarisa kana zvese zvishandiso zvinoshandisa ma frequency akafanana.
3. Bvisa zvese zvakafa kubva kumasonganiro. Zvikasadaro uchaona kunonoka kwakanyanya.
4. Usamboshandisa bhatiri midziyo yekurara isina yepakati controller.
5. Usavhote FLIRS zvishandiso.
6. Ita shuwa kuti une yakakwana mains powered mudziyo kuti ubatsirwe kubva kune meshing

Kushamwaridzana - imwe mudziyo inodzora imwe mudziyo

Z-Wave zvishandiso zvinodzora zvimwe Z-Wave zvishandiso. Ukama pakati pemudziyo mumwe
kudzora mumwe mudziyo kunonzi kushamwaridzana. Kuti udzore zvakasiyana
mudziyo, mudziyo unodzora unofanirwa kuchengetedza runyoro rwemidziyo inogashira
kudzora mirairo. Aya mazita anonzi mapoka ekubatana uye anogara aripo
zvine chekuita nezvimwe zviitiko (semuenzaniso bhatani rakadzvanywa, sensor trigger, ...). Zvikazo
chiitiko chinoitika ese maturusi akachengetwa muboka rekubatana achaita
gamuchira imwechete isina waya yekuraira isina waya, kazhinji iyo 'Basic Set' Command.

Mapoka eMasangano:

Nhamba YebokaMaximum NodesDescription

1

4

Z-Wave Uyezve Lifeline

Configuration Parameters

Z-Wave zvigadzirwa zvinofanirwa kushanda kunze kwebhokisi mushure mekuiswa, zvisinei
kumwe kugadziridzwa kunogona kugadzirisa basa zvirinani kune zvinodiwa nemushandisi kana kuvhura mberi
kuvandudzwa maitiro.

ZVINOKOSHA: Vadzori vanogona chete kubvumidza kugadzirisa
dzakasaina tsika. Kuti uise kukosha muhuwandu 128 ... 255 kukosha kwakatumirwa mukati
chikumbiro chichava kukosha kunodiwa kubvisa 256. For example: Kuisa a
parameter kusvika 200  ingangodiwa kuseta kukosha kwe200 minus 256 = minus 56.
Kana iri mbiri yebhayiti kukosha kwakafanana kunoshanda: Values ​​yakakura kupfuura 32768 inogona
inoda kupihwa sehunhu husina kunaka zvakare.

Parameter 1: Delta Yakavakirwa Chinja Chimiro Kubika

Iyi gadziriso inogonesa iyo switch mamiriro ekuzivisa, kana switch chimiro chachinja kuti OFF kuenda ON kana ON kuti OFF.
Saizi: 1 Byte, Default Value: 1

SettingDescription

Parameter 2: Nguva yenguva yakavakirwa Switch Status Reporting

Iyi gadziriso inogonesa shanduko yemamiriro ekuzivisa zvichienderana nenguva yenguva yakagadziriswa. Cherechedzo: Ma controller anogona chete kubvumidza kugadzirisa zvakasainwa. Kuti uise kukosha muchikamu 32768 65520, kukosha kwakatumirwa mukunyorera kuchaenzana neukoshi hunodiwa kubvisa 65520. For ex.ample, kuseta nguva intervalto 36000 masekonzi zvingadiwa kuseta kukosha 3600065536=29536.
Saizi: 2 Byte, Default Value: 0

SettingDescription

Parameter 3: Relay uye LED kugadzirisa

Ichi chigadziriso chinoshandiswa kushandura relay LED mamiriro kana relay yakavhurika / yakavharika uye zvakare inogonesa kuti ichengetedze yekupedzisira relay mamiriro pamusoro pemagetsi kutenderera.0 - Relay chimiro hachizochengetwe pamusoro pemagetsi kutenderera, uye Relay chimiro LED ichavhenekera kana relay ON uye relay chimiro LED inodzima kana relay OFF. 1 - Relay mamiriro achachengetwa pamusoro pemagetsi kutenderera, uye Relay chimiro LED ichavhenekera kana relay ON uye relay chimiro LED ichadzima kana relay OFF.2 - Relay chimiro hachizochengetwe pamusoro pemagetsi kutenderera, uye Relay chimiro LED chinodzima kana relay ON uye relay mamiriro LED ichavhenekera kana relay OFF.3 - Relay mamiriro achachengetwa pamusoro pemagetsi kutenderera, uye Relay chimiro LED ichadzima kana relay ON uye relay chimiro LED ichavhenekera kana relay OFF.
Saizi: 1 Byte, Default Value: 0

SettingDescription

Technical Data

Hardware Platform	ZM5202
Device Type	On/Off Power Switch
Network Kushanda	Nguva Dzose Pamuranda
Firmware Shanduro	01
Z-Wave Vhezheni	6.51.02
Chitupa ID	ZC10-15020011
Z-Wave Chigadzirwa Id	0x0059.0x000E.0x0001
Frequency	XXfrequency
Maximum transmission simba	XXantenna

Tsanangudzo yeZ-Wave chaiyo mazwi

• Controller - iri Z-Wave mudziyo une kugona kubata network.
  Ma controller anowanzo magedhi, Remote Controls kana bhatiri rinoshandiswa madziro controller.
• Muranda - iri Z-Wave chishandiso chisina kugona kubata network.
  Varanda vanogona kunge vari masensa, actuators uye kunyange kure kure.
• Primary Controller - ndiye murongi wepakati wetiweki. Zvinofanira kuva
  controller. Panogona kuve nemutongi mumwe chete wekutanga muZ-Wave network.
• Kubatanidzwa - ndiyo maitiro ekuwedzera michina mitsva yeZ-Wave mune network.
• Kusabatanidzwa - ndiyo maitiro ekubvisa Z-Wave zvishandiso kubva kunetiweki.
• Kushamwaridzana - hukama hwekutonga pakati pemudziyo unodzora uye
  mudziyo unodzorwa.
• Wakeup Chiziviso -imeseji yakakosha isina waya yakapihwa neZ-Wave
  mudziyo wekuzivisa unokwanisa kutaura.
• Node Information Frame -imeseji yakakosha isina waya inoburitswa nea
  Z-Wave mudziyo kuzivisa kugona kwayo uye mabasa.