MITSUBISHI SC-SL2N-E Central Kudzora neLCD Display

Ruzivo rwechigadzirwa: Central Control SC-SL2N-E
Iyo Central Control SC-SL2N-E ndeye chaiyo midziyo inoenderana neEMC Directive 2004/108/EC uye LV Directive 2006/95/EC. Yakagadzirirwa kudzora kushanda kwemukati nekunze zvikamu zveSuper Link modhi. Chigadzirwa chacho chinouya neCD yemushandisi, chinja mavara ekuratidza, pan-head screws, uye denderedzwa crimping terminals semidziyo.

Kuchengetedza:

• YAMBIRO: Basa rekuisa rinofanirwa kuendeswa kune mutengesi kana nyanzvi yekuisa kuti adzivise basa risina kukwana, kuvhunduka kwemagetsi, uye moto.
• CHENJERERO: Tevedzera mirairo nekungwarira kudzivirira kuisa zvisizvo izvo zvinogona kukonzera mhedzisiro yakaipa sekukuvara kwakanyanya kana kufa.
• Kuiswa kunofanira kuitwa maererano nemitemo yenyika wiring neanokwanisa magetsi injiniya.
• Bata chigadzirwa nehanya yakakwana kudzivirira kukanganisa nekuda kwekudonha uye kutsikwa.
• Usati wabata terminal block, dzima magetsi.

Mirayiridzo Yekushandiswa Kwechigadzirwa

1. Verenga bhuku rekuisa nokungwarira uye ritevere usati waisa basa. Tarisa kune yemukati yuniti uye yekunze yuniti yekumisikidza bhuku pamwe chete kubasa rekuisa.
2. Isa chigadzirwa zvakanaka maererano nebhuku rekuisa. Kusagadzikwa kusina kukwana kunogona kukonzera kuvhunduka kwemagetsi uye kuguma kwemoto.
3. Ita basa rekugadzirisa. Usabatanidza waya yepasi nemapombi egasi, pombi dzemvura, tsvimbo yemheni, uye waya yepasi yefoni.
   Kusakwana kwepasi basa kunogona kukonzera kuvhunduka kwemagetsi.
4. Iva nechokwadi chekubatanidza kwakasimba uye kusungirira tambo dzakataurwa zvakachengeteka kuitira kuti materminal connections asave pasi pesimba rekunze rinoshanda patambo. Kusakwana kubatanidza kune terminal wiring kunogona kukonzera kuvhunduka kwemagetsi uye moto unozoguma.
5. Mushure mekuisa, ita bvunzo kumhanya uye simbisa kuti hapana abnormalities inoitika panguva yebvunzo kumhanya.
6. Tsanangura nzira yekushanda kune vatengi maererano nebhuku remushandisi.
7. Kumbira vatengi kuti vachengete bhuku rekuisa kuti rizoshandiswa mune ramangwana.

Kudzora kwepakati uku kunoenderana neEMC Directive 2004/108/EC, LV Directive 2006/95/EC.

INSTALLATION Manual

• Ndapota iva nechokwadi chekuverenga bhuku rino zvakanyatsonaka uye kuritevera usati waisa basa.
• Ndokumbira utarise kune yemukati yuniti uye yekunze yuniti yekumisikidza bhuku pamwe chete yebasa rekuisa.
• Chishandiso chinofanira kuiswa zvinoenderana nemirairo yenyika wiring.
•  Chigadzirwa chacho chakanyatso midziyo, saka ndapota chibate nehanya yakakwana kudzivirira iyo unit kukuvara nekuda kwekudonha nekutsikwa.
• Usati wabata terminal block, dzima magetsi.

Chengetedzo Yekuchengetedza

• Ndokumbira uverenge iyi "Safety Precautions" yeKuisa basa uye uitevere nemazvo.
• Chengetedzo Yekuchengetedza yakakamurwa kuita "Yambiro" uye "Kuchenjerera".

YAMBIRO: Kuisa zvisizvo kunogona kukonzera mhedzisiro yakaipa sekukuvara kwakanyanya kana kufa.
CHENJERERO: Kuisa zvisizvo kunogona kukonzera mhedzisiro yakaipa zvichienderana nemamiriro ezvinhu.

Ndapota iva nechokwadi chekutevera murairo.
Mushure mekuisirwa, ndapota ita bvunzo kumhanya uye simbisa kuti hapana abnormalities inoitika panguva yekumhanya bvunzo. Ndapota tsanangura nzira yekushanda kune vatengi maererano nebhuku remushandisi. Ndokumbirawo mukumbire vatengi kuti vachengete bhuku rekuisa iri.

YAMBIRO

• Ndokumbira utumire basa rekuisa kune mutengesi kana nyanzvi yekuisa. Kuzvimisikidza kunogona kukonzera kusakwana basa, kuvhunduka kwemagetsi uye moto unozokonzera.
• Ndapota isa chikwata zvakanaka maererano nebhuku rekuisa. Kusagadzikwa kusina kukwana kunogona kukonzera kuvhunduka kwemagetsi uye moto unobva waita.
• Ndokumbira uve nechokwadi chekushandisa zvakanamirwa zvishongedzo uye zvikamu zvakatemwa zvebasa rekuisa, kana zvinogona kukonzera kuvhunduka kwemagetsi uye moto unozoguma.
• Basa remagetsi rinofanirwa kuitwa neanokwanisa enjiniya yemagetsi, maererano , uye wiring tsanangudzo. Basa risina kukwana rekuisa rinogona kukonzera kuvhunduka kwemagetsi uye moto unoguma.
• Kana wiring, ita shuwa kubatana kwakasimba uye sunga tambo dzakataurwa zvakachengeteka kuitira kuti materminal kubatanidza asave pasi pesimba rekunze rinoshanda patambo. Kusakwana kubatanidza kune terminal wiring kunogona kukonzera kuvhunduka kwemagetsi uye moto unozoguma.

KUCHENJERA

• Ndapota ita basa rekuisa pasi.
  Ndapota usabatanidza waya yepasi nemapombi egasi, pombi dzemvura, tsvimbo yemheni uye foni yepasi waya. Kusakwana kwepasi basa kunogona kukonzera kuvhunduka kwemagetsi.
• Ndapota usaise central control panzvimbo dzinotevera.

1. Oiri fog yakazadzwa nzvimbo, kupfapfaidza mafuta uye nzvimbo ine steamy sekicheni, nezvimwe.
2. Nzvimbo iyo gasi rinoparadza rakaita sesarufa dhiokisi inogadzirwa.
3. Nzvimbo ine muchina unogadzira radio wave.
   Inogona kukonzera kusagadzikana muhurongwa hwekutonga uye kumhanya zvisina kujairika.
4. Nzvimbo iri panjodzi yekupisa gasi rinodonha.
   Nzvimbo iyo iripo inovhuvhuta yekubata moto chinhu senge pendi yakaonda uye peturu.
   Nechero mukana gasi rinodonha uye rinoungana rakatenderedza mudziyo, rinogona kukonzera kupisa.

Mienzaniso Inoshanda

Mhando dzese dzeSuper Link

Accessories

Ndokumbira utarise zvinotevera zvishongedzo.

Shandisa bhokisi reMagetsi kuisa. Ndokumbira ugadzirire panzvimbo.

Kuisa Basa

Ndokumbira uise central control mushure mekudzima simba nekutya kuvhunduka kwemagetsi.
Ndapota ronga kana kudzivirira wiring kuitira kuti simba rakawandisa rirege kushandiswa kune waya dzemagetsi.
Kudzora maPCB (akadhindwa edunhu mabhodhi) akaiswa kune ese epamusoro uye epasi makesi.
Chenjerera kuti usakuvadza maPCB paunenge uchishandisa screwdriver uye mamwe maturusi.
MaPCB anogona kukuvadzwa nemagetsi akamira, uye saka iva nechokwadi chekuburitsa chero magetsi akamira akaunganidzwa pamuviri wako usati watanga basa.
(Magetsi akasimba anogona kuburitswa nekubata bhodhi rekutonga uye zvimwe zvikamu zvakadzika.)

Kuisa Nzvimbo
Ndokumbira uise munzvimbo yemukati isingaonekwe nemagetsi emagetsi, mvura, huruva, kana zvimwe zvinhu zvekunze.
Tembiricha yekushanda yechigadzirwa ichi inobva pa0°C kusvika pa40°C.
Isa munzvimbo iyo tembiricha ye ambient inoramba iri mukati meiyo tembiricha yekushanda.
Nekudaro, kana tembiricha yekushanda yakapfuurwa, iva nechokwadi chekushandisa matanho ekugadzirisa senge kuisirwa feni yekutonhora.
Ziva kuti kuramba uchishandiswa kweiyi central control kunze kweiyo tembiricha yekushanda kunogona kukonzera matambudziko ekushanda.

Nzvimbo Inodiwa Pakuiswa

Service Space

1. Muchiitiko chekuisa pane control board
   Ndapota iva nechokwadi chekukiya bhodhi rekudzivirira kuchengetedza vanhu kubva kune magetsi.
   Dzivisa kushandiswa kwezvinhu zvinochengetedza kupisa uye zvinhu zvinodzivirira kupisa nekuti izvi zvinogona kukonzera kupisa kuvakwa uye kukanganisa zvakanyanya kushanda kweyepakati control.
2. Panyaya yekupinda mumadziro
   Ndapota tarisa kuti pane nzvimbo yakakwana mukati memadziro. Kana tembiricha mukati memadziro ichipfuura 40 ° C, isa iyo yepakati control pane control board.
   Kuchenjerera
   Ndokumbira usaise zvishandiso zvinogona kukonzera kuti ambient tembiricha ikwire mubhodhi rimwechete rekudzora. Zvakare, usaise akawanda ma controller mune imwechete control board. Izvi zvinogona kuita kuti kupisa kuwedzere uye kunokonzera kushanda kwenhema. Kana akawanda epakati control achifanira kuiswa mubhodhi rimwe chete rekutonga, tora matanho ekugadzirisa kuti uve nechokwadi chekuti tembiricha mubhodhi rekutonga haikwire kupfuura 40 ° C sekunge nekuisa mafeni ekutonhodza.

   
   Paunenge uchiita kuenderera mberi kuisirwa kweakawanda controller, iva nechokwadi chekuwana chinhambwe pakati pemayuniti nenzvimbo yebasa sezvakaratidzwa mumufananidzo.

   

Installation Procedure

1. Muchiitiko chekumisikidza mumadziro, kutanga, simbisa waya yemagetsi, waya yechiratidzo, uye bhokisi reMagetsi.
   Chengeta waya yemagetsi newaya yechiratidzo zvakapatsanurwa kudzivirira kusashanda zvakanaka.

   

   1. Vhura nyaya yepamusoro nekutevera nzira iri pasi apa.
      1. Bata mapindiro ari kurudyi nekuruboshwe, wodhonza kumberi kuti uvhure kavha ichidzika.
      2. Shandisa Phillips-head screwdriver kubvisa screw. (Chenjerera kuti usarase screw.)
      3. Vhura chikamu chepamusoro munzira ④ uchidzvanya zvinyoro nyoro chikamu chepamusoro.

         

      4. Shandisa yakapihwa ④ pan-head screws kuchengetedza yepakati control kubhokisi remagetsi kana control board.

         

      5. Shandisa screwdriver chaiyo kugadzira zvigadziriso zvekusarudza. (Kuti uwane ruzivo, ona chikamu 5 Kudzora Kuchinja Kusarudza.)
      6. Bvisa pepa rekudzivirira pachiratidziro chepakati control. Zvakakosha
      7. Isa iyo yepamusoro kesi kumashure munzvimbo yayo yepakutanga mune yepasi kesi sepakutanga, uye simbisa kesi yekuisa screws ( Kuiswa maitiro (2) ②).
         Izvi zvinopedzisa maitiro ekumisikidza.
         Kuchenjerera
         Iyo kesi uye magetsi ekupa kit chinhu chakabatanidzwa. Ndapota usavaparadzanisa.

Electrical Wiring

Nezvikonzero zvekuchengetedza, ndapota shandisa matenderedzwa crimping terminals ane insulated sleeve yekubatanidza waya dzese kune yepakati control.

• Ndapota ita basa rekuisa pasi. Ndokumbira usabatanidze tambo yepasi nemapombi egasi, pombi dzemvura, mheni tsvimbo uye tambo yekumisa runhare.
• Ndapota usabatidze magetsi (switch yemunharaunda) kusvikira basa rose rapera.
• Ndokumbira umbomira maminetsi maviri mushure mekunge mayunitsi emukati neekunze abatidzwa usati wabatidza magetsi.
• Kunze kwekutonga kwepakati mumufananidzo, zvese zvezvikamu zvinowanikwa panzvimbo (waya, switch, relays, magetsi, l.amps, nezvimwewo).
• Ndokumbirawo uve nechokwadi chekuvaka iyo breaker iyo inowanikwa nyore nyore neaya yemidziyo yekuvaka.
• Ndokumbirawo muve nechokwadi chekushandisa materminal crimping anopihwa kana muchibatanidza waya kune magetsi terminal block uye Super Link terminal block.
• Ndokumbira ushandise mudziyo wekuisa chinodiwa, chimbo chekumisa chekumisikidza uye chekunze chekushandisa chekushandisa nguva zvinoenderana neIEC Safety Standard.

Tarisa kumufananidzo uri pazasi weiyo terminal orientation.

Wiring Outline

Usati wabatanidza mawaya, bvisa chivharo chechivharo chekupedzisira. Mushure mekunge basa rapera, gadzirisa chivharo cheterminal block sepakutanga. Chivharo chinoshandiswa kudzivirira kuvhunduka kwemagetsi nekuda kwekusangana netsaona.

Wiring Magadzirirwo

Simba rekupa waya	1.25mm2
Switch yemunharaunda	10A
Super Link chiratidzo waya (Cherechedzo 1, Cherechedzo 2)	0.75mm2 - 1.25mm2 shielded waya (MVVS 2-core) Max. 1000m pamutsetse (Max. chinhambwe: 1000m, Hurefu hwewaya: 1000m)
Operation kubuda, kukanganisa kuburitsa, kudiwa kwekuisa, emergency stop yekuisa, yekunze timer yekuisa waya	0.75mm2 - 1.25mm2 CCV, CPEV (2-core) Max. 200m
Kuchengeta waya	0.75mm2 - 6mm2

Cherechedzo 1: Kana ichi chepakati chekutonga chikashandiswa, shandisa waya yakadzivirirwa yeSuper Link chiratidzo waya.
Isai migumo yese yewaya yakavharirwa.
(Batanidza pasi pekutonga kwepakati kune chikamu mu "System Wiring".

Cherechedzo 2: Kana zvikamu zvemukati nekunze zvakabatana kunetiweki zvese zvinowirirana neNew Super Link, hurefu hwewaya hwe1500m pamutsetse unogoneka (chinhambwe chikuru: 1000m). Zvisinei, iva nechokwadi chekushandisa 0.75mm2 waya dhayamita kana hurefu hwewaya hunopfuura 1000m. Kuti uwane rumwe ruzivo, ndapota taura nemumiriri wako wekutengesa kana
mutengesi.

System Wiring

1. Ndokumbira ubatanidze pasi kuitira chiratidzo waya uye waya yemagetsi.
2. Iyo yakasarudzwa relay inowanikwa panzvimbo ino inofanirwa kuve neinotevera zvirevo: rated voltage yeDC 12V uye yakanyanya kushandiswa kwesimba kweDC 0.9W kana pasi (80mA kana pasi)
3. Iyo yakasarudzwa relay inowanikwa panzvimbo ino inofanirwa kuve neanotevera maratidziro: Non-voltage "a" yekupinda yekubatanidza uye inokwanisa kumirisana neyakaiswa shoma mutoro weDC 12V uye 10mA kana zvishoma.
   Iwo DO uye DI materminals ari polar.
   Usabatanidza waya nhatu kana kupfuura kune imwechete terminal.
   CHERECHEDZA
   Usabatanidza waya yemagetsi kune imwe terminal.
   Kuita kubatanidza kusiriyo kunogona kukonzera kukuvara kana kupisa kwezvikamu zvemagetsi uye kune njodzi huru.
   Ndokumbira utarise waya zvakare usati wabatidza magetsi.

Kudzora Switch Selection

Zvinogoneka kushandura marongero sezvinotevera nemaseting ePCB switch SW1 kuenda kuSW10, J1, J2, uye J3 pane yepakati control. Ndapota shandura kutonga panzvimbo yepaiti sezvinodiwa. Zvinokurudzirwa kushandura marongero nekushandisa mutyairi chaiwo.

Switch

SW Nha.		Default	ON	DZIMA	Tsanangudzo
SW	1	ON	Ona tafura kurudyi	Ona tafura kurudyi	Simba kukundikana kubhadhara basa
	2	ON
	3	DZIMA	Auto mode inogona kusetwa	Auto mode haigone kusetwa	Automatic mode kuratidza
	4	ON	Display	Hapana kuratidza	Sefa chiratidzo chinoratidza pa/kudzima
	5	ON	New	Previous	Zvitsva/Prev. Super Link(*1)
	6	ON	Center & blower	Center	Kutumira data panguva yekudiwa kwekuisa
	7	DZIMA			(Keep at Off)
	8	DZIMA	Nguva Mwedzi.Zuva	Mwedzi.Zuva Nguva	Kuratidzwa kwenhoroondo yezvikanganiso
	9	DZIMA			(Keep at Off)
	10	DZIMA			(Keep at Off)

Jumper waya

	Short circuit (default)	Kana yadimburwa	Function
J1	Setting zvinogoneka	Kuisa hazviiti (Kusanganisira panguva yekuisa kunze.)	Center/Remote setting (*2) (Kusanganisira iyo inotenderwa / yakarambidzwa marongero ega ega remo rekudzora basa)
J2			(Usabvisa.)
J3			(Usabvisa.)

Simba kukundikana muripo webasa sarudzo

SW-1	SW-2	Function
ON	ON	Kutumira kwezvirongwa zvepurogiramu kana simba radzoka pa (Mamiriro ekushanda simba risati ratumirwa kana pasina purogiramu kana simba richidzoka.)
ON	DZIMA	Kutumira mamiriro ekushanda simba risati rapera
DZIMA	ON	(Usaite iyi gadziriro.)
DZIMA	DZIMA	Hapana data inotumirwa kana magetsi adzoka

1. Kuchinja kunodiwa kana kubatana kwacho kwapfuura Super Link.
   Rudzi chairwo rwekubatanidza netiweki (Itsva kana yapfuura Super Link) zvinoenderana nemamodheru emayuniti emukati nemayuniti ekunze, nezvimwewo. Ndokumbira ubate agency kana mumiririri Wekutengesa.
2. Kana J1 ikabviswa, iyo Center / Remote haigadzirwe kubva pane ino yepakati control. Ndokumbirawo mubvise kana akawanda epakati ma control akaiswa uye imwe huru yepakati control iripo.
   Kana J1 yadimburwa, data rinotumirwa kune inofuridza chete panguva yekudiwa kwekuisa (hapana chinoitwa kana SW6 yadzimwa) uye yekumira chete panguva yekumisikidzwa kwekumira.

Kuisa Kudzora Target Units

Ita zvigadziro zvezvikwata kuti zvidzorwe nekutonga kwepakati.
Pamagadzirirwo ekugadzirisa, ona bhuku remushandisi rakanamirwa kune central contrl.
Pakutakura, hapana chimwe chezvikamu zvinoiswa sezvikamu zvinotarirwa zvekutonga, uye saka mauniti anofanirwa kudzorwa neiyi central control anofanirwa kugadzikwa sematanho ekudzora.
Mhando nhatu dzezvigadziriso zviripo.

1. Zvikwata zvinosarudzwa sezvinangwa zvekutonga zvepakati pekutonga uye controlledas boka rekugadzirisa Boka
2.  Mauniti anosarudzwa sezvinangwa zvekutonga zvepakati pekutonga asi zvisina kuunganidzwa Individual setting
3. Mauniti haana kusarudzwa sezvinangwa zvekutonga zvepakati kudzora (kana mayuniti achadzorwa neimwe yepakati control) Kwete mayuniti anotangwa ekutonga.
   Iva nechokwadi chekuseta nguva iripo. Izvi zvinodikanwa kune marongero echirongwa uye kukanganisa nhoroondo yekuratidzira.
   Batidza simba uye dzvanya mabhatani matatu (MENU, RESET, GROUP No. 10) kamwechete kupfuura maminetsi mashanu, anogona kutanga zvigadziriso zvemukati.

Kudzora kweboka kana uchishandisa akawanda mayuniti
Iyi yepakati kutonga inogona kudzora anosvika makumi matanhatu nemana anotangwa mayunitsi (anosvika makumi mana nemasere mayunitsi kana uchishandisa yapfuura Super Link kuseta). Multiple central controls inofanira kuiswa kudzora 64 kana kupfuura air conditioner units.
Kana uchibatanidza akawanda epakati kudzora pane imwechete network, chero marongero eboka anogona kugadzirwa kune yega yega yepakati control.

Zvinyorwa / Zvishandiso

MITSUBISHI SC-SL2N-E Central Kudzora neLCD Display [pdf] Bhuku reMirayiridzo SC-SL2NA-E, SC-SL2N-E Yepakati Kudzora ine LCD Ratidza, Yepakati Kudzora ine LCD Ratidza, LCD Ratidza

References

• User Manual