Keri Systems NXT-RM3 Reader Interface Module
INSTALLATION GUIDE
1.0 Wiring uye Kurongeka Dhiyagiramu
1. 1 Reader Interface Module (RIM} Diagram
Cherechedza: Midziyo iyi yakaedzwa uye yakawanikwa inoenderana nemiganhu yeKirasi A yedhijitari mudziyo, zvichienderana neChikamu 15 cheFCC Mitemo. Aya mallmlt akagadzirwa kuti ape dziviriro inonzwisisika kubva mukukanganisa kunokuvadza kana michina ichishandiswa munzvimbo yekutengeserana. Mudziyo uyu unogadzira, unoshandisa, uye unogona kuvheneka redhiyo frequency simba uye, ukasaiswa uye ukashandiswa zvinoenderana negwaro rekuraira, unogona kukonzera kukanganisa kusinganzwisisike pakufambiswa kwemashoko neredhiyo.
1.2 MS Reader Wiring Diagram
1.3 Wiegand Reader Wiring Digiramu (Mutsetse Mumwechete LED)
1.4 Wiegand Reader Wiring Diagram (Dual Line LED)
2.0 Reader Grounding
Sezvinoratidzwa mumadhayagiramu emuverengi, nhovo / dhiza waya yechero muverengi / tambo dzeparipheral.
INOFANIRA kugumiswa kune imwe yeanotevera mapoinzi
- iyo yakasvibira pasi lug (J6) pane controller (inoratidzwa),
- chero kona yekona inonamatira controller kune yakavharirwa,
- Pini 3 yeTB10,
- kana pasi pevhu remukombe.
YAMBIRO: Kutadza kuisa pasi zvakanaka muverengi / peripheral drain wire kunogona kukonzera kusavimbika kutaurirana kana kushanda kweiyo yakabatanidzwa peripheral.
3.0 Zvinotsanangurwa
3.1 Saizi
- Kana yaiswa paNXT Controller
- 2.50 inches kureba ne 2.0 inches yakafara ne 1.0 inch kudzika, isingasanganisire wiring connectors
- 6.4 masendimita ne5.0cm ne2.5cm
3.2 Simba/Zvazvino Zvinodiwa
- 10 kusvika 14 VDC@ 100 mA (yakanyanya kudhirowa ikozvino pa12 VDC)
3.3 Operating Conditions
- 32°F kusvika 150°F (0°C kusvika 60°C) – 0% kusvika 90% Relative Humidity, isingadzorere
3.4 Cable Zvinodiwa
Iyo yakazara RIM yekuverenga tambo kureba inofanira kunge isingasviki 500 tsoka.
Cherechedza: Patambo refu inomhanya, tambo kuramba inokonzera kudonha In voltage pakupera kwetambo run. Ita shuwa kuti simba rakakodzera uye razvino rechishandiso chako rinowanikwa pamudziyo pakupera kwetambo run.
a. Mageji anorema kupfuura akanyorwa anogamuchirwa nguva dzose.
4.0 RIM Configuration
Iyo RIM inobvumira Kari MS kana Wiegand vaverengi / zvitupa kuti zvizivikanwe uye kuverengerwa neNXT controllers. Iyo yekumisikidza RIM kumisikidzwa ndeyeMS-Series Reader uchishandisa maviri mitsara LED control (yakawanda-mavara). Ita nhanho dzinotevera kugadzirisa iyo RIM yechishandiso chako. Tarisa kune Dhirowa iri papeji 1 yekuchinja uye nzvimbo dzeLED, uye Tafura iri papeji 3 yekuchinja uye tsananguro dzeLED.
4.1 Pinda Programming Mode
1. Bata pasi zvese SW1 neSW2 kwemasekonzi maviri.
2. Ma LED ese manomwe ari paRIM achapenya katatu.
3. Sunungura zvose SW1 neSW2, uye chikwata chave mukugadzirisa mode.
4. Kana yave mugadziriso mode, SW1 nhanho pakati pezvasarudzo - SW2 inosarudza iyo inoratidzwa ikozvino sarudzo.
4.2 Sarudza Rudzi Rwako rweKuverenga
Mhando dzeKeri MS (D4), Wiegand (D5), Keri Keypad (D6), uye Wiegand Keypad/Reader Combo (D7) dziri kutsigirwa parizvino.
1. Dzvanya SW1 kuti upfuure nemhando dzevaverengi dzinotsigirwa. Kudhinda kwega kwega kweSW1 kunoenda kune inotevera rudzi rwemuverengi.
2. Kana rudzi rwemuverengi rwaunoda rwavhenekerwa, tinya SW2. Rudzi rwemuverengi rwaiswa.
3. Kana wakasarudza Wiegand (D5), Keri Keypad (D6), kana Wiegand Combo (D7) kuverenga mode, chikwata chave chagadzirira kugadzirisa iyo RIM's LED line control mode.
Enda kuchikamu 3.3 kune mirairo yekumisikidza.
4. Kana wasarudza Keri MS (D4) kuverenga modhi, dzvanya SW2 kaviri. Iyo RIM ikozvino yakagadziriswa uye iyo unit inotangazve kugamuchira iyo mitsva paramita. Ese manomwe ma LED anopenya katatu sezvo iyo unit inotangazve neiyo mitsva yekumisikidza paramita. Kana ma LED amira kupenya, iyo unit iri kushanda.
Ongorora: Usabvisa simba kubva kuRIM panguva yekudzorerazve. Kurasika kwesimba panguva yekumisikidza kuchaita kusashanda chero shanduko yemagadzirirwo yawakaita.
4.3 Sarudza Yako Wiegand Reader LED Line Configuration
Dual-line control ndiyo yakasarudzika RIM yekumisikidza ye LED mutsara kumisikidzwa. Uku ndiko kuisirwa kunodiwa kweKeri Keypad muverengi. Ita matanho anotevera ekuchinja pakati pe-single-line uye mbiri-mutsara LED control.
1. Dzvanya SW1 kuti upinde nepakati pemhando dzekugadzirisa mutsara we LED. Imwe neimwe press yeSW1 inotsika kune inotevera LED mutsara mhando.
2. Kana yaidiwa LED mutsetse control mode LED yakavhenekerwa, tinya SW2. Iyo LED mutsara wekutonga modhi ikozvino yaiswa.
3. Dzvanya SW2 kaviri uye RIM ikozvino yakagadziridzwa uye chikwata chinotangazve kugamuchira zvitsva zvitsva.
4. Iwo maRI M's LEDs achange akadzimwa kweinenge 10 masekonzi sezvo chikwata ichizvigadzirisa pachayo. Ese manomwe ma LED anopenya sezvo iyo unit iri kutangazve neiyo mitsva yekumisikidza paramita. Kana ma LED amira kupenya, iyo unit iri kushanda.
Cherechedza: Usabvisa simba kubva kuRIM panguva yekudzorerazve. Kurasika kwesimba panguva yekumisikidza kuchaita kusashanda chero shanduko yemagadzirirwo yawakaita.
4.4 Kuongorora RIM Configuration
Iyo inoenderana muverengi mhando uye mutsara wekutonga modhi ma LED anovhenekerwa panguva yekushanda. Kuti usimbise zvigadziriso zvako, tarisa kudhirowa kwekutanga kwegwaro rekuchinja uye nzvimbo dzeLED, uye tafura inotevera yekuchinja uye tsananguro dzeLED.
a. Tafura inoshanda kune RI.M Finnware v03.01.06 uye gare gare. Ndokumbira uvandudze firmware yako sezvinodiwa.
https://help.kefisys.com/portal/en/kb/articles/rm3-installation#10Wiring_and_Layout_Diagrams
Zvinyorwa / Zvishandiso
 |
Keri Systems NXT-RM3 Reader Interface Module [pdf] Installation Guide NXT-RM3 Reader Interface Module, Reader Interface Module, Interface Module, Module |
