IDEC MQTT Sparkplug B ine Lgnition User Guide

To enable MQTT/SparkPlug functionality, install the necessary modules via Config -> SYSTEM -> Modules.
Select and install the downloaded module to integrate MQTT support.

Changing OPC-UA Server Configuration

After installing MQTT modules, configure the OPC-UA server by going to Config -> OPC UA -> Server Settings.
Tarisa iyo 'Ratidza advanced zvivakwa' cheki bhokisi uye gonesa 'Expose Tag Providers' kupedzisa kuseta.

Ignition Installation & Setup

Dhawunirodha uye Isa Ignition

Dhawunirodha iyo Ignition inoitwa pano.
https://inductiveautomation.com/downloads/ignition
Download the file for the platform you are using.
See here for installation instructions.
https://docs.inductiveautomation.com/display/DOC81/Installing+and+Upgrading+Ignition
For non-Windows operating systems, there are instruction links for Linux and macos, respectively.

Install Ignition

Download an installer from our Downloads page.
Run the installer and follow the steps in the installation wizard.
- Click here if you’re installing on Linux…
- Click here if you’re installing on macOS…

Setup Instructions for using

MQTT/Sparkplug B with Ignition

Kupinda mukati Ignition

Mushure mekuisa, isa izvi URL mubrowser yekuwana port 8088 pakombuta inomhanyisa Ignition.
http://localhost:8088/

Follow the steps and click “Finish Setup”.
Tevere, izvi zvinounza yekutanga Ignition skrini sezvakaratidzwa pazasi.
Kana iyo yekutanga skrini ikabuda, tinya bhatani rekuti "Log In" mukona yekurudyi kuti upinde.

Zita rekushandisa nepassword rinoshandiswa kupinda mukati zvakangofanana neaya panguva yekuisa Ignition.

Kushandisa MQTT/Sparkplug B ine Ignition

Ignition haitsigire MQTT kana SparkPlug mune yayo yekutanga mamiriro (pakarepo mushure mekuiswa).

MQTT/SparkPlug can be supported by installing an additional MQTT module. – The MQTT module can be downloaded here.
- https://inductiveautomation.com/downloads/third-party-modules/
- Kune mana maMQTT module akapihwa neIgnition.
  - The Distributor Module and Engine Module must be installed.
- (Inodiwa) MQTT Distributor Module
  - Add MQTT broker functionality to Ignition.
- (Inodiwa) MQTT Engine Module
  - Add the ability to connect the MQTT broker (Distributor Module) and Ignition
- (Sarudzo) MQTT Transmission Module
  - Add MQTT node (Publisher/Subscriber) functionality.
  - If Ignition is used as SCADA, it will work without it (required if on the device side)
- (Sarudzo) MQTT Recorder Module
  - Install if you want to create a history of data communicated by MQTT Sparkplug.
Kune iyo MQTT module, vhura Ignition's "Config" -> "SYSTEM" -> "Modules".

Dzvanya "Isa kana Simudzira Module ...". Dzvanya "Isa kana Simudzira Module ...".
Sarudza iyo module yakatorwa uye tinya bhatani rekuti "Isa" kuti utange kuisirwa.

Kana iyo yekumisikidza yapera, iyo Module Configuration skrini inoratidza iyo yakaiswa modules.
Mushure mekuisa mamodule ane hukama neMQTT, iyo OPC-UA server configuration inofanira kuchinjwa uye kugadzirisa zvakare. (nekuti MQTT inobatwa sechinhu cheOPC-UA)

Kugadzirisa zvakare OPC-UA server, sarudza "Config", "OPC UA", "Server Settings" uye tarisa "Ratidza advanced properties" checkbox.
Zvadaro, batidza "Expose Tag Providers” checkbox
Reset the OPC-UA server after changing the settings. To reset,open “Config” -> “SYSTEM” -> “Modules

Dzvanya bhatani re "restart" kurudyi kwe "OPC-UA.
Pakutanga, data inogona kutumirwa kubva kuMQTT node (device side) kuenda kuIgnition, asi kwete munzira yekudzokera kumashure (Ignition to MQTT node).
This can be deactivated by setting To do this, open “Config”->”MQTT ENGINE”- >”Settings” and uncheck “Block Node Commands” (for Nodes) and “Block Device Commands” (for Devices) in “Command Settings.
Iyo MQTT Distributor module inoita basa reMQTT bhuroka, asi kana yasvika kubva kune MQTT node (mudziyo), huchokwadi hunoitwa nezita remushandisi uye password.
This user name and password are set from “Config” -> “MQTT DISTRIBUTOR” -> “Settings” -> “Users”.
To create a new user, click “Create new MQTT Users…” on this screen. Click “Create new MQTT Users…” on this screen to create a new user.
Kana iwe ukagadzira mushandisi mutsva, unoseta zita rekushandisa uye password, asi unoisawo maropafadzo (ACLs) emushandisi uyu.
Kuti ubvumire kupinda kwekuverenga/kunyora kumisoro yese yeakaundi yemushandisi yauri kuseta, isa "RW #".

How to check the MQTT communication

Mushure mekuiswa kweMQTT-ane hukama mamodule uye kumisikidzwa kweOPC-UA kwapera, iwe unozogona kutarisa MQTT-ane hukama paramita sezvinhu zveOPCUA.
Open “Config” -> “OPC CLIENT” -> “OPC Quick Client”,
Expand the tree in the order of “Ignition OPC UA Server” > “Tag Providers” > “MQTT Engine”.
Nodes connected by Sparkplug are displayed under “MQTT Engine”

Mibvunzo Inowanzo bvunzwa

Q: Ndingawana sei iyo Ignition interface mushure mekuiswa?
A: Simply enter http://localhost:8088/ in a web browser to log in and access Ignition.

Mubvunzo: Ndeapi maMQTT modules anodiwa eIgnition?
A: The required modules include MQTT Distributor and MQTT Engine, with optional modules like MQTT Transmission and MQTT Recorder.

Zvinyorwa / Zvishandiso

IDEC MQTT Sparkplug B ine Lgnition [pdf] Bhuku reMushandisi
MQTT Sparkplug B ine Lgnition, MQTT, Sparkplug B ine Lgnition, ine Lgnition, Lgnition

References

User Manual

IDEC MQTT Sparkplug B ine Lgnition

Product Information

Mirayiridzo Yekushandiswa Kwechigadzirwa