EPH INODZORA R37V2 3 Zone Programmer User Guide

Installation Instructions

Factory Default Settings

Zvinotsanangurwa

Chiratidziro cheLCD

1. Inoratidza nguva iripo.
2. Inoratidza zuva razvino revhiki.
3. Inoratidza kana kudzivirira kwechando kunoitwa.
4. Inoratidza kana keypad yakavharwa.
5. Inoratidza zuva razvino.
6. Inoratidza zita renzvimbo.
7. Inoratidza ikozvino modhi.

Bhatani Tsanangudzo

Wiring Diagram

Mounting & Installation

Chenjero!

• Kuiswa uye kubatana kunofanirwa kuitwa chete nemunhu ane hunyanzvi.
• Vagadziri vemagetsi vanokwanisa chete kana vashandi vane mvumo yebasa vanotenderwa kuvhura mugadziri.
• Kana iyo programmer ikashandiswa nenzira isina kutaurwa nemugadziri, kuchengetedza kwayo kunogona kukanganisa.
• Usati wamisa mugadziri, zvinodikanwa kuti upedze ese anodiwa marongero anotsanangurwa muchikamu chino.
• Usati watanga kuisa, mugadziri anofanira kutanga abviswa kubva kune mains.

Iyi programmer inogona kuiswa pamusoro kana kukwidziridzwa kune yakadzoreredzwa conduit bhokisi.

1. Bvisa programmer kubva pakurongedzerwa kwayo.
2. Sarudza nzvimbo yekumisikidza yemugadziri:
   - Isa iyo programmer 1.5 metres kumusoro kwepasi.
   -Dzivirira kuratidzwa kwakananga kuchiedza chezuva kana zvimwe zvinodziya / kutonhora masosi.
3. Shandisa philips screwdriver kusunungura screws yebackplate pasi pemugadziri. Iyo programmer inosimudzwa kumusoro kubva pasi uye inobviswa kubva kumashure.
   (Ona mufananidzo 3 papeji 7)
4. Nyora iyo backplate pane yakadzoreredzwa conduit bhokisi kana zvakananga kumusoro.
5. Waya bheti rekumashure sezviri padhayagiramu yewaya iri papeji 6.
6. Gara mugadziri pabackplate uchiita chokwadi chekuti mapini emugadziri uye madhiri ebackplate ari kugadzira ruzha, sundidzira mugadziri wepurogiramu achikwira kumusoro uye simbisa screws dzebackplate kubva pasi. (Ona mufananidzo wechitanhatu papeji 6)

Operating Instruction

Kukurumidza sumo kune yako R37V2 programmer:

Iyo R37V2 programmer ichashandiswa kudzora nzvimbo nhatu dzakapatsanurwa mukati mako yekudziya system.
Imwe neimwe zone inogona kushanda yakazvimirira uye kurongwa kuti ienderane nezvido zvako. Nzvimbo yega yega ine mapurogiramu anosvika matatu emazuva ese ekudziya anonzi P1, P2 uye P3. Ona Peji 13 kuti uwane mirayiridzo yekuti ungagadzirisa sei zvirongwa zvepurogiramu.
PaLCD skrini yemugadziri wako uchaona zvikamu zvitatu zvakasiyana, chimwe chinomiririra imwe neimwe nzvimbo.
Mukati mezvikamu izvi iwe unogona kuona kuti iyo zone iri pari modhi ipi.
Kana iri muAUTO modhi, inozoratidza kana iyo zone ichitevera kurongwa kuti ibatiswe ON kana KUDZIMWA.
Nezve `Sarudzo yeModhi' ndapota ona peji 11 kuti uwane imwe tsananguro.
Kana iyo zone iri ON, iwe uchaona iyo tsvuku LED yeiyo zone mwenje kumusoro. Izvi zvinoratidza kuti simba riri kutumirwa kubva kumugadziri panzvimbo ino.

Mode Selection

AUTO

Pane nzira ina dziripo pakusarudza.

AUTO Iyo zoni inoshanda kusvika katatu 'ON/OFF' nguva pazuva (P1, P2, P3).
ZUVA RESE Iyo zoni inoshanda imwe chete 'ON/OFF' nguva pazuva. Izvi zvinoshanda kubva panguva yapfuura 'ON' kusvika panguva yechitatu 'OFF'.
ON Iyo zone iri zvachose ON.
DZIMA Nzvimbo yacho yakadzimwa zvachose.
Dzvanya Sarudza kuti uchinje pakati peAUTO, ZUVA RESE, ON & OFF.
Iyo yazvino modhi icharatidzwa pachiratidziri pasi peiyo mhando zone.
Iwo Sarudza anowanikwa pasi pebutiro rekutanga. Zone imwe neimwe ine yayo Sarudza.

Programming Modes

Uyu mugadziri ane anotevera maprogramming modes. 5/2 Zuva modhi Kuronga Muvhuro kusvika Chishanu sechivharo chimwe uye
5/2 Zuva modhi Kuronga Muvhuro kusvika Chishanu sechivharo chimwe uye Mugovera neSvondo se2nd block.
7 Zuva modhi Kuronga ese mazuva manomwe ega.
24 Hour mode Kuronga mazuva ese 7 sebhuroka rimwe.

Factory Program Settings 5/2d

Gadzirisa iyo Chirongwa Setting mu5/2 Zuva Modhi

Reviewkuisa Zvirongwa zvePurogiramu

Dzvanya PROG.
Dzvanya OK kuti ufambe mukati menguva dzezuva rega rega (block of days).
Dzvanya Sarudza kusvetukira kuzuva rinotevera (block of days).
Dzvanya MENU kuti udzokere kune zvakajairika.
Iwe unofanirwa kudzvanya chaiyo Sarudza kuti udzokeview hurongwa hwenzvimbo iyoyo.

Boost Function

Imwe neimwe nzvimbo inogona kukwidziridzwa kwemaminetsi makumi matatu, 30, 1 kana maawa matatu apo zone iri muAUTO, ZUVA ROSE & OFF mode. Dzvanya Boost 2, 3, 1 kana 2 nguva, kuisa yaunoda BOOST nguva kuZone. Kana Boost ikadzvanywa pane kunonoka kwechipiri kusati kwaitwa apo `BOOST' ichapenya pachiratidziro, izvi zvinopa mushandisi nguva yekusarudza yaunoda BOOST nguva. Kukanzura BOOST, dzvanya iyo Boost yakafanana zvakare. Kana nguva yeBOOST yapera kana kukanzurwa, iyo Zone inodzokera kumodhi yaimboshanda pamberi peBOOST.
Cherechedza: A BOOST haigone kushandiswa uri muON kana Holiday Mode.

Basa repamberi

Kana nzvimbo iri muAUTO kana ALLDAY modhi, iyo Advance basa inobvumira mushandisi kuunza zone kana nzvimbo kumberi kune inotevera nguva yekuchinja. Kana iyo zone yave panguva yekuve OFF uye ADV yakatsikirirwa, iyo zone ichabatidzwa ON kusvika pakupera kwenguva inotevera yekuchinja. Kana iyo zone yave panguva yekuve ON uye ADV yakatsikirirwa, iyo zone ichadzimwa kusvika panotanga nguva inotevera yekuchinja. Dzvanya ADV. Zone1, Zone 2, Zone 3 uye Zone 4 ichatanga kupenya. Dzvanya yakakodzera Sarudza. Iyo zone icharatidza `ADVANCE ON' kana `ADVANCE OFF' kusvika pakupera kwenguva inotevera yekuchinja. Zone 1 inomira kupenya uye kupinda Advance mode. Zone 2 uye Zone 3 icharamba ichipenya. Dzokorora maitiro aya neZone 2 uye Zone 3 kana zvichidikanwa. Dzvanya OK Kuti ukanzure ADVANCE, tinya yakakodzera Sarudza . Kana nguva yeADVANCE yapera kana kukanzurwa, nzvimbo yacho inodzokera kumodhi yaimboshanda pamberi peADVANCE.

Menu

Iyi menyu inobvumira mushandisi kugadzirisa mamwe mabasa. Kuti uwane menyu, dzvanya MENU .

P01 Kuisa Zuva, Nguva uye Chirongwa cheModhi DST ON

Cherechedza: Ndokumbira utarise peji 12 kune tsananguro dzeProgramming Modes.

P02 Holiday Mode

P03 Frost Dziviriro YADZIMWA

Chiratidzo cheFrost chicharatidza pachiratidziri kana mushandisi akachimisa mumenyu.

Kana tembiricha yekamuri yemukati ikadonha pasi peinodikanwa tembiricha yechando, nzvimbo dzese dzemugadziri dzinoita uye chiratidzo chechando chinopenya kusvika tembiricha yekudzivirira chando yawanikwa.

P04 Zone Title

Iyi menyu inobvumira mushandisi kusarudza mazita akasiyana enzvimbo yega yega. Zvisarudzo ndezvi:

P05 PIN

Iyi menyu inobvumira mushandisi kuisa kiyi yePIN pamugadziri wepurogiramu. Kukiya kwePIN kunoderedza kushanda kwemugadziri.
Gadzirisa PIN

Copy Basa

Copy basa rinogona kushandiswa chete kana iyo 7d modhi yasarudzwa. (Ona peji 16 kuti usarudze 7d modhi) Dzvanya PROG kuronga nguva dzeON uye OFF dzezuva revhiki raunoda kukopa. Usadzvanya OK pane P3 OFF nguva, siya iyi nguva ichipenya. Dzvanya ADV, `COPY' ichaonekwa pachiratidziri, nezuva rinotevera revhiki richipenya. Kuti uwedzere hurongwa hwaunoda kusvika nhasi dzvanya . Kudarikira zuva iri dzvanya . Dzvanya OK kana chirongwa chashandiswa kumazuva aunoda. Ita shuwa kuti nzvimbo iri mu `Auto' modhi kuti iyi purogiramu ishande zvinoenderana. Dzokorora maitiro aya kuZone 2 kana Zone 3 kana zvichidikanwa.
Ongorora: Iwe haugone kukopa masheti kubva kune imwe nzvimbo kuenda kune imwe, Eg Kukopa Zone 1 hurongwa kuZone 2 hazvigoneke.

Backlight Mode Sarudzo ON

Pane 3 backlight marongero aripo ekusarudza:
AUTO Backlight inogara yakabatidzwa kwemasekonzi gumi kana chero bhatani rikadzvanywa.
ON Backlight inobatidzwa zvachose.
OFF Backlight iri Off zvachose.

Kugadzirisa backlight dzvanya uye bata OK kwemasekonzi gumi. `Otomatiki' inoonekwa pachiratidziri. Dzvanya kana kushandura modhi pakati peAuto, On uye Off. Dzvanya OK kuti usimbise sarudzo uye kudzokera kune yakajairika kushanda.

Kukiya Keypad

Resetting the Programmer

Kugadzirisa zvakare programmer kune zvigadziriso zvefekitori:
Dzvanya MENU .
'P01' ichaonekwa pachiratidziri.
Dzvanya kusvika 'P06 reSET' yaonekwa pachiratidziri.
Dzvanya OK kuti usarudze.
'nO' ichatanga kupenya.
Dzvanya , kuchinja kubva pa'nO' kuenda 'YES'.
Dzvanya OK kuti usimbise.
Iyo programmer ichatangazve uye yodzokera kune yayo fekitori yakatsanangurwa marongero.
Nguva uye zuva hazvizogadzirwe patsva.

Master Reset

Kuti ugone kuseta zvakare mugadziri kune zvigadziriso zvefekitori, tsvaga bhatani reseta bhatani kurudyi-kurudyi pasi pemugadziri. (ona peji 5) Dzvanya bhatani reReset Master worisunungura. Iyo skrini ichaenda isina chinhu uye reboot. Iyo programmer ichatangazve uye yodzokera kune yayo fekitori yakatsanangurwa marongero.

Service Interval OFF

Iyo nguva yebasa inopa mugadziri kugona kuisa yegore countdown timer pane programmer. Kana iyo Service Interval ikamiswa `SERv' ichaonekwa pachiratidziri iyo inozivisa mushandisi kuti yavo yegore boiler sevhisi inofanirwa.
Kuti uwane ruzivo rwekugonesa kana kudzima iyo Service Interval, ndapota taura nevatengi.

EPH Inodzora IE
technical@ephcontrols.com www.ephcontrols.com/contact-us T +353 21 471 8440

EPH Inotonga UK
technical@ephcontrols.co.uk www.ephcontrols.co.uk/contact-us T +44 1933 322 072

Zvinyorwa / Zvishandiso

	EPH ZVINOTAURA R37V2 3 Zone Programmer [pdf] Bhuku reMushandisi R37V2 3 Zone Programmer, R37V2, 3 Zone Programmer, Zone Programmer, Programmer
	EPH ZVINOTAURA R37V2 3 Zone Programmer [pdf] Bhuku reMirayiridzo R37V2 3 Zone Programmer, R37V2, 3 Zone Programmer, Zone Programmer, Programmer

References

• User Manual