EPH INODZORA R27-V2 2 Zone Programmer

Factory Default Settings

• Contacts: 230VAC
• Chirongwa: 5/2D
• Backlight: On
• Keypad Kiya: Off
• Kudzivirira Frost: Off
• Operating Mode: Auto
• Pin Lock: Off
• Nguva yeSevhisi: Off
• Zone Title: MVURA KUSVIRA

Zvinotsanangurwa

• Magetsi: 230VAC
• Ambient Temperature: 0 … 50˚C
• Dimensions: 161 x 100 x 31 mm
• Contact Rating: 3(1)A Chirongwa Memory 5 Makore
• Tembiricha Sensor: NTC 100K
• Backlight: Chena
• IP Rating: IP20
• Bhatiri: 3VDC Lithium LIR2032 & CR2032
• Backplate: British System Standard
• Digirii rekusvibisa: 2 (Kupikisa voltaguye surge 2000V; maererano ne EN60730)
• Software Kirasi: Kirasi A

Chiratidziro cheLCD

1. Inoratidza nguva iripo.
2. Inoratidza zuva razvino revhiki.
3. Inoratidza kana kudzivirira kwechando kunoitwa.
4. Inoratidza kana keypad yakavharwa.
5. Inoratidza zuva razvino.
6. Inoratidza zita renzvimbo.
7. Inoratidza ikozvino modhi.

Bhatani Tsanangudzo

Wiring Diagram

Terminal Connections

• Nyika
• N Neutral
• L Rarama
• 1 Zone 1 OFF - N/C Kazhinji yakavharwa kubatana
• 2 Zone 2 OFF - N/C Kazhinji yakavharwa kubatana
• 3 Zone 1 ON - Kwete / O Kazhinji yakavhurika yekubatanidza
• 4 Zone 2 ON - Kwete / O Kazhinji yakavhurika yekubatanidza

Mounting & Installation

Chenjero!

• Kuiswa uye kubatana kunofanirwa kuitwa chete nemunhu ane hunyanzvi.
• Vagadziri vemagetsi vanokwanisa chete kana vashandi vane mvumo yebasa vanotenderwa kuvhura mugadziri.
• Kana iyo programmer ikashandiswa nenzira isina kutaurwa nemugadziri, kuchengetedza kwayo kunogona kukanganisa.
• Usati wamisa mugadziri, zvinodikanwa kuti upedze ese anodiwa marongero anotsanangurwa muchikamu chino.
• Usati watanga kuisa, mugadziri anofanira kutanga abviswa kubva kune mains.

Iyi programmer inogona kuiswa pamusoro kana kukwidziridzwa kune yakadzoreredzwa conduit bhokisi.

1. Bvisa programmer kubva pakurongedzerwa kwayo.
2. Sarudza nzvimbo yekumisikidza yemugadziri:
   • Isa iyo programmer 1.5 metres kumusoro kwepasi.
   • Dzivirira kuratidzwa zvakananga kuchiedza chezuva kana zvimwe zvinodziya / kutonhora masosi.
3. Shandisa philips screwdriver kusunungura screws yebackplate pasi pemugadziri. Iyo programmer inosimudzwa kumusoro kubva pasi uye inobviswa kubva kumashure.
   (Ona mufananidzo 3 papeji 7)
4. Nyora iyo backplate pane yakadzoreredzwa conduit bhokisi kana zvakananga kumusoro.
5. Waya bheti rekumashure sezviri padhayagiramu yewaya iri papeji 6.
6. Gara mugadziri pabackplate uchiita chokwadi chekuti mapini emugadziri uye madhiri ebackplate ari kugadzira ruzha, sundidzira mugadziri wepurogiramu achikwira kumusoro uye simbisa screws dzebackplate kubva pasi. (Ona mufananidzo wechitanhatu papeji 6)

Kukurumidza sumo kune yako R27V2 programmer:
Iyo R27 V2 programmer ichashandiswa kudzora nzvimbo mbiri dzakapatsanurwa mune yako yepakati yekudziya system. Imwe neimwe zone inogona kushanda yakazvimirira uye kurongwa kuti ienderane nezvido zvako. Nzvimbo yega yega ine mapurogiramu anosvika matatu emazuva ese ekudziya anonzi P1, P2 uye P3. Ona Peji 13 kuti uwane mirayiridzo yekuti ungagadzirisa sei zvirongwa zvepurogiramu. PaLCD skrini yemugadziri wako uchaona zvikamu zviviri zvakasiyana, chimwe chinomiririra imwe neimwe nzvimbo. Mukati mezvikamu izvi unokwanisa kuona kuti iyo zone iri mu modhi ipi pari zvino. Kana iri muAUTO modhi, inotaridza kana iyo zone ichizotevera kurongwa kuti ibatiswe kana KUDZIMWA. Nezve 'Mode Selection' ndapota ona peji 11 kuti uwane imwe tsananguro. Kana iyo zone iri ON, iwe uchaona iyo tsvuku LED yeiyo zone mwenje kumusoro. Izvi zvinoratidza kuti simba riri kutumirwa kubva kumugadziri wechirongwa ichi.

Mode Selection

Pane nzira ina dziripo pakusarudza.

• AUTO Iyo zoni inoshanda kusvika katatu 'ON/OFF' nguva pazuva (P1,P2,P3).
• ZUVA RESE Iyo zoni inoshanda imwe chete 'ON/OFF' nguva pazuva. Izvi zvinoshanda kubva panguva yekutanga 'ON' kusvika panguva yechitatu 'OFF'.
• ON Iyo zone iri zvachose ON.
• DZIMA Nzvimbo yacho yakadzimwa zvachose.
• Dzvanya Sarudza kuti uchinje pakati peAUTO, ZUVA RESE, ON & OFF.
• Iyo yazvino modhi icharatidzwa pachiratidziri pasi peiyo zone chaiyo.
• Iwo Sarudza anowanikwa pasi pebutiro rekutanga. Zone imwe neimwe ine yayo Sarudza.

Programming Modes

Uyu mugadziri ane anotevera maprogramming modes.

• 5/2 Zuva modhi Kuronga Muvhuro kusvika Chishanu sechivharo chimwe uye Mugovera neSvondo se2nd block.
• 7 Zuva modhi Kuronga ese mazuva manomwe ega.
• 24 Hour mode Kuronga mazuva ese 7 sebhuroka rimwe.

Factory Program Setting

Gadzirisa iyo Chirongwa Setting mu5/2 Zuva Modhi

• Dzvanya PROG.
• Chirongwa cheMuvhuro kusvika Chishanu cheZone1 chasarudzwa.

Kuti uchinje programming yeZone 2, tinya yakakodzera Sarudza.

• Press  + uye – kugadzirisa P1 PANE nguva.
• Dzvanya OK .
• Press + uye – kugadzirisa iyo P1 OFF nguva.
• Dzvanya OK .
• Dzokorora maitiro aya kugadzirisa P2 uye P3 nguva.
• Chirongwa cheMugovera kusvika Svondo chasarudzwa.
• Press + uye – kugadzirisa P1 PANE nguva.
• Dzvanya OK .
• Press + uye – kugadzirisa iyo P1 OFF nguva.
• Dzvanya OK .
• Dzokorora maitiro aya kugadzirisa P2 uye P3 nguva.
• Dzvanya MENU kuti udzokere kune zvakajairika.

Uchiri muchirongwa chekugadzira, kudzvanya Sarudza kuchasvetukira kuzuva rinotevera (block remazuva) pasina kuchinja chirongwa.
Gadzirisa iyo Chirongwa Setting mu5/2 Zuva Modhi

Cherechedza:

1. Kuti uchinje kubva pa5/2d kuenda ku7D kana 24H hurongwa, tarisa kupeji 16, Menyu P01.
2. Kana iwe usingade kushandisa imwe kana akawanda ezvirongwa zvezuva nezuva wobva waisa nguva yekutanga uye nguva yekupedzisira kuti ifanane. For exampuye, kana P2 yakagadzirirwa kutanga na 12: 00 uye kupera na 12: 00 mugadziri anongorega purogiramu iyi uye opfuurira kune imwe nguva yekuchinja.

Reviewkuisa Zvirongwa zvePurogiramu

• Dzvanya PROG.
• Dzvanya OK kuti ufambe mukati menguva dzezuva rega rega (block of days).
• Dzvanya Sarudza kusvetukira kuzuva rinotevera (block of days).
• Dzvanya MENU kuti udzokere kune zvakajairika.
• Iwe unofanirwa kudzvanya chaiyo Sarudza kuti udzokeview hurongwa hwenzvimbo iyoyo.

Boost Function

• Imwe neimwe nzvimbo inogona kukwidziridzwa kwemaminetsi makumi matatu, 30, 1 kana maawa matatu apo zone iri muAUTO, ZUVA ROSE & OFF mode.
• Dzvanya Boost 1, 2, 3 kana 4 nguva, kuisa yaunoda BOOST nguva kuZone.
• Kana Boost ikadzvanywa pane kunonoka kwemasekondi mashanu isati yaitwa apo 'BOOST' ichapenya pachiratidziro, izvi zvinopa mushandisi nguva yekusarudza yaunoda BOOST nguva.
• Kukanzura BOOST, dzvanya iyo Boost yakafanana zvakare.
• Kana nguva yeBOOST yapera kana kukanzurwa, iyo Zone inodzokera kumodhi yaimboshanda pamberi peBOOST.

Cherechedza: A BOOST haigone kuiswa uri muON kana Holiday Mode.

Basa repamberi

Kana nzvimbo iri muAUTO kana ALLDAY mode, iyo Advance basa inobvumira mushandisi kuunza zone kana nzvimbo mberi kune inotevera nguva yekuchinja.

• Kana iyo zone yave panguva yekuve OFF uye ADV yakatsikirirwa, iyo zone ichabatidzwa ON kusvika pakupera kwenguva inotevera yekuchinja. Kana iyo zone yave panguva yekuve ON uye ADV yakatsikirirwa, iyo zone ichadzimwa kusvika panotanga nguva inotevera yekuchinja.
• Dzvanya ADV.
• Zone1 uye Zone 2 ichatanga kupenya.
• Dzvanya yakakodzera Sarudza.
• Iyo zoni icharatidza 'ADVANCE ON' kana 'ADVANCE OFF' kusvika pakupera kwenguva inotevera yekuchinja.
• Zone 1 inomira kupenya uye kupinda Advance mode.
• Zone 2 icharamba ichipenya.
• Dzokorora maitiro aya neZone 2 kana zvichidikanwa.
• Dzvanya OK .
• Kukanzura ADVANCE, tinya yakakodzera Sarudza .
• Kana nguva yeADVANCE yapera kana kukanzurwa, nzvimbo yacho inodzokera kumodhi yaimboshanda pamberi peADVANCE.

Menu Basa

Iyi menyu inobvumira mushandisi kugadzirisa mamwe mabasa. Kuti uwane menyu, dzvanya MENU .

P01 Kuisa Zuva, Nguva uye Chirongwa cheModhi DST ON

• Dzvanya MENU , 'P01 tInE' ichaonekwa pachiratidziri.
• Dzvanya OK , gore richatanga kupenya.
• Press + uye – kugadzirisa gore.
• Dzvanya OK .
• Press + uye – kugadzirisa mwedzi.
• Dzvanya OK .
• Press + uye – kugadzirisa zuva.
• Dzvanya OK .
• Press + uye – kugadzirisa awa.
• Dzvanya OK .
• Press + uye – kugadzirisa miniti.
• Dzvanya OK .
• Press + uye – kugadzirisa kubva 5/2d kusvika 7d kana 24h modhi.
• Dzvanya OK .
• Press + uye – kubatidza DST (Day Light Saving time) On or Off.
• Dzvanya MENU uye mugadziri achadzokera kune zvakajairika kushanda.

Cherechedza:
Ndokumbira utarise peji 12 kune tsananguro dzeProgramming Modes.

P02 Holiday Mode

Iyi menyu inobvumira mushandisi kudzima yavo yekudziya system nekutsanangura zuva rekutanga uye rekupedzisira.

• Dzvanya MENU, 'P01' ichaonekwa pachiratidziri.
• Press + kusvika 'P02 HOL' ichaonekwa pachiratidziri.
• Dzvanya OK, 'HOLIDAY FROM', zuva uye nguva zvichaonekwa pachiratidziri. Gore richatanga kupenya.
• Press + uye – kugadzirisa gore. Dzvanya OK .
• Press + uye – kugadzirisa mwedzi. Dzvanya OK .
• Press + uye – kugadzirisa zuva. Dzvanya OK .
• Press + uye – kugadzirisa awa. Dzvanya OK .

'HOLIDAY TO' uye zuva nenguva zvichaonekwa pachiratidziri. Gore richatanga kupenya.

• Press + uye – kugadzirisa gore. Dzvanya OK .
• Press + uye – kugadzirisa mwedzi. Dzvanya OK .
• Press + uye – kugadzirisa zuva. Dzvanya OK .
• Press + uye – kugadzirisa awa. Dzvanya OK .
• Iyo programmer zvino ichadzimwa panguva iyi yakasarudzwa. Kukanzura HOLIDAY, dzvanya OK .
• Iyo programmer ichadzokera kune yakajairika kushanda kana zororo rapera kana kukanzurwa.

P03 Frost Dziviriro YADZIMWA

Iyi menyu inobvumira mushandisi kumutsa kudzivirira kwechando pakati pe5°C ne20°C. Kudzivirirwa kwechando kunogadzikwa ku OFF.

• Dzvanya MENU, 'P01' ichaonekwa pachiratidziri.
• Press + kusvika 'P03 FrOST' yaonekwa pachiratidziri.
• Dzvanya OK, 'OFF' ichaonekwa pachiratidziri.
• Press + kusarudza 'ON'. Dzvanya OK . '5˚C' ichapenya pachiratidziro.
• Press + uye – kusarudza tembiricha yako yaunoda kudzivirira chando. Dzvanya OK .
• Dzvanya MENU uye mugadziri achadzokera kune zvakajairika kushanda.

Chiratidzo cheFrost chicharatidza pachiratidziri kana mushandisi akachimisa mumenyu.

Kana tembiricha yekamuri yemukati ikadonha pasi peinodikanwa tembiricha yechando, nzvimbo dzese dzemugadziri dzinoita uye chiratidzo chechando chinopenya kusvika tembiricha yekudzivirira chando yawanikwa.

P04 Zone Title

Iyi menyu inobvumira mushandisi kusarudza mazita akasiyana enzvimbo yega yega.

Zvisarudzo ndezvi:

• DEFAULT OPTIONS RENAME ZVINHU
  • HOT WATER ZONE 1
  • HEATING ZONE 2
• Dzvanya MENU, 'P01' ichaonekwa pachiratidziri.
• Press + kusvika 'P04' yaonekwa pachiratidziri.
• Dzvanya OK , 'MVURA inopisa' ichapenya pachiratidziro.
• Press + kuchinja kubva pa'MVUVA INOPITSA' kuenda 'ZONE 1'. Dzvanya OK . 'KUSVIRA' kuchapenya pachiratidziri.
• Press + kuchinja kubva ku'HEATING' kuenda ku'ZONE 2'.
• Dzvanya MENU uye mugadziri achadzokera kune zvakajairika kushanda.

P05 PIN

Iyi menyu inobvumira mushandisi kuisa kiyi yePIN pamugadziri wepurogiramu. Kukiya kwePIN kunoderedza kushanda kwemugadziri.

Gadzirisa PIN

• Dzvanya MENU, 'P01' ichaonekwa pachiratidziri.
• Press + kusvika 'P05 PIN' yaonekwa pachiratidziri.
• Dzvanya OK, 'OFF' ichaonekwa pachiratidziri.
• Dzvanya kuti uchinje kubva pa OFF kuenda pa ON. Dzvanya OK . '0000' ichapenya pachiratidziro.
• Dzvanya + uye – kuseta kukosha kubva pa0 kusvika pa9 kune yekutanga digit. Dzvanya OK kuti uende kune inotevera PIN digit.
• Kana nhamba yekupedzisira yePIN yaiswa, tinya OK. Verify inoratidzwa ne '0000'.
• Press + uye – kuseta kukosha kubva pa0 kusvika pa9 kune yekutanga digit. Dzvanya OK kuti uende kune inotevera PIN digit.
• Kana nhamba yekupedzisira yePIN yaiswa, tinya OK. Iyo PIN ikozvino yakasimbiswa, uye PIN yekiyi yakavhurwa.

Kana iyo yekusimbisa PIN ikaiswa zvisizvo mushandisi anodzoserwa kumenyu. Kana iyo PIN yekuvhara ichishanda iyo Lock chiratidzo ichapenya sekondi yega yega pachiratidziri. Kana iyo programmer iPIN yakakiyiwa, kudzvanya menyu kunoendesa mushandisi kuPIN yekuvhura skrini.

Cherechedza:
Kana iyo PIN yekuvhara yakagoneswa, BOOST nguva inoderedzwa kusvika pamaminitsi makumi matatu uye nguva yeawa imwe. Kana iyo PIN yekuvhara yakagoneswa, Mode Sarudzo inoderedzwa kuita Auto uye OFF.

Kuti uvhure PIN

• Dzvanya MENU, 'UNLOCK' ichaonekwa pachiratidziri. '0000' ichapenya pachiratidziro.
• Press + uye – kuseta kukosha kubva pa0 kusvika pa9 kune yekutanga digit.
• Dzvanya OK kuti uende kune inotevera PIN digit.
• Kana iyo yekupedzisira nhamba yePIN yaiswa. Dzvanya OK .
• Iyo PIN ikozvino yavhurwa.
• Kana PIN yakavhurwa pane programmer, inozozvimisikidza zvakare kana pasina bhatani rakadzvanywa kwemaminetsi maviri.

Kudzima PIN
Kana PIN yakavhurwa (ona mirairo iri pamusoro)

• Dzvanya MENU, 'P01' ichaonekwa pachiratidziri.
• Press + kusvika 'P05 PIN' yaonekwa pachiratidziri.
• Dzvanya OK, 'ON' ichaonekwa pachiratidziri.
• Press + or – kusarudza 'OFF'. Dzvanya OK . '0000' ichapenya pachiratidziro. Isa PIN. Dzvanya OK .
• Iyo PIN ikozvino yakadzimwa.
• Dzvanya MENU kuti udzokere kune zvakajairika kana kuti inozobuda yega mushure memasekondi makumi maviri.

Copy Basa

Copy basa rinogona kushandiswa chete kana iyo 7d modhi yasarudzwa. (Ona peji 16 kuti usarudze 7d modhi) Dzvanya PROG kuronga nguva dzeON uye OFF dzezuva revhiki raunoda kukopa. Usadzvanya OK pane P3 OFF nguva, siya iyi nguva ichipenya. Dzvanya ADV, 'COPY' ichaonekwa pachiratidziro, nezuva rinotevera revhiki richipenya. Kuti uwedzere hurongwa hwaunoda kusvika nhasi dzvanya + .
Kudarikira zuva iri dzvanya –.Dzvanya OK kana purogiramu yashandiswa kumazuva anodiwa. Ita shuwa kuti nzvimbo iri mu 'Auto' modhi kuti iyi hurongwa ishande zvinoenderana. Dzokorora maitiro aya eZone 2 kana zvichidikanwa.

Cherechedza:
Iwe haugone kukopa masheti kubva kune imwe nzvimbo kuenda kune imwe, Eg Kukopa Zone 1 hurongwa kuZone 2 hazvigoneke.

Backlight Mode Sarudzo ON

Pane 3 backlight marongero aripo ekusarudza:

• AUTO Backlight inogara yakabatidzwa kwemasekonzi gumi kana chero bhatani rikadzvanywa.
• ON Backlight inobatidzwa zvachose.
• DZIMA Backlight iri Off zvachose.

Kugadzirisa backlight dzvanya uye bata OK kwemasekonzi gumi. 'Auto' inoonekwa pachiratidziri.

• Press + or – kushandura modhi pakati peAuto, On uye Off.
• Dzvanya OK kuti usimbise sarudzo uye kudzokera kune yakajairika kushanda.

Kukiya Keypad

Kuti uvhare mugadziri, dzvanya wobata + uye – pamwe chete kwemasekonzi matatu. ichaonekwa pachiratidziri. Mabhatani ava kuremara. Kuti uvhure mugadziri, dzvanya uye ubate + uye – kwe 10 seconds. ichanyangarika kubva pahwindo. Mabhatani ava kugoneswa.

Resetting the Programmer

• Kugadzirisa zvakare programmer kune zvigadziriso zvefekitori:
• Dzvanya MENU . 'P01' ichaonekwa pachiratidziri.
• Press + kusvika 'P06 reSET' yaonekwa pachiratidziri.
• Dzvanya OK kuti usarudze. 'nO' ichatanga kupenya.
• Press + , kuchinja kubva pa'nO' kuenda 'YES'.
• Dzvanya OK kuti usimbise.
• Iyo programmer ichatangazve uye yodzokera kune yayo fekitori yakatsanangurwa marongero.
• Nguva uye zuva hazvizogadzirwe patsva.

Master Reset

Kuti ugone kuseta zvakare mugadziri kune zvigadziriso zvefekitori, tsvaga bhatani reseta bhatani kurudyi-kurudyi pasi pemugadziri. (ona peji 5) Dzvanya bhatani reReset Master worisunungura. Iyo skrini ichaenda isina chinhu uye reboot. Iyo programmer ichatangazve uye yodzokera kune yayo fekitori yakatsanangurwa marongero.

Service Interval OFF

Nguva yebasa inopa mugadziri kugona kuisa yegore countdown timer pane programmer. Kana iyo Service Interval ikamiswa 'Serv' ichaonekwa pachiratidziro iyo inozivisa mushandisi kuti yavo yegore boiler sevhisi inofanirwa. Kuti uwane ruzivo rwekugonesa kana kudzima iyo Service Interval, ndapota taura nevatengi.

EPH Inodzora IE

• technical@ephcontrols.com www.ephcontrols.com/contact-us T +353 21 471 8440

EPH Inotonga UK

2022 EPH Controls Ltd. technical@ephcontrols.co.uk www.ephcontrols.co.uk/contact-us T +44 1933 322 072

Zvinyorwa / Zvishandiso

	EPH INODZORA R27-V2 2 Zone Programmer [pdf] Mirayiridzo R27-V2 2 Zone Programmer, R27-V2, 2 Zone Programmer, Programmer
	EPH INODZORA R27 V2 2 Zone Programmer [pdf] Bhuku reMirayiridzo R27 V2 2 Zone Programmer, R27 V2, 2 Zone Programmer, Zone Programmer, Programmer

References

• User Manual