Danfoss 3060 Electro Mechanical Programmer
Installation Instructions
Ndapota Cherechedza:
Ichi chigadzirwa chinofanirwa kuiswa chete neane electrician kana anokwanisa kupisa yekuisa, uye inofanirwa kunge ichienderana neyazvino edition yeIEEE wiring mitemo.
Product specification
| Tsanangudzo | |
| Magetsi | 230 ± 15% Vac, 50/60Hz |
| Chinja chiito | 2 x SPST, mhando 1B |
| Chinja chiyero | Max 264 Vac, 50/60Hz, 3(1) A |
| Kurongeka kwenguva | ± 1 min/mwedzi |
| Enclosure rating | IP30 |
| Max. ambient tembiricha | 55°C |
| Dimensions, mm (W, H, D) | 102 x 210 x 60 |
| Chigadzirwa chakakosha | EN 60730-2-7 |
| Kuvaka | Kirasi 1 |
| Kudzora Kusvibisa Situation | Dhigirii 2 |
| Yakatemwa Impulse Voltage | 2.5kV |
| Bhora Pressure Test | 75°C |
Installation
- Bvisa dial yepasi yekuseta. Isa ese mana matepi kumusoro kwepamusoro dial. Unscrew 4BA screw uye bvisa outer case.
- Slaen ma screws maviri kuchengetedza plug-in module kubackplate uye kupatsanura module kubva kumashure nekukwevera kumusoro.
- Gadzirisa backplate kumadziro (3 hole kugadzirisa).
- Uchitaura kune madhayagiramu ewaya pazasi uye akapesana ita kubatanidza magetsi sekuratidzwa (sezvinoshanda). Iwo madhayagiramu anoratidza kuti materminal 3 uye 5 haana mukati akabatana neanogadzira uye anogona kushandiswa seasara wiring terminals kana zvichidikanwa.
- Kureruka kwekuisa kunogona kuwanikwa kuburikidza nekushandiswa kweDanfoss Randall Wiring Center iyo inowanikwa kubva kune vakawanda Vavaki Vatengesi uye Vanogovera.
CHERECHEDZA: Kana Wiring Center ikashandiswa tevera iyo yekumisikidza mirairo inosanganisirwa neiyo unit uye kwete anotevera wiring diagram. - Chengetedza tambo cores pasi petambo clamp.
Wiring
WIRING – FULLLY PUMPED SYSTEM
CHERECHEDZA: Iyi unit haina kukodzera kushandiswa ine mota yakazara zone mavharuvhu anoda zvese ON uye OFF masaini emagetsi kana ashandiswa mukudziya wedunhu.
WIRING – GRAVITY HOT WATER SYSTEM
Mirayiridzo Yemushandisi
Your programmer
- Iyo 3060 programmer inokutendera kuti uchinje mvura yako inopisa nekudziya nekudzima dzimwe nguva dzinoenderana newe.
- Matepi mana padhiya renguva anokutendera kuti usarudze paunoda kuti mvura yako inopisa uye kudziyisa zviuye nekudzima zuva rega rega. Iyo programmer inopa 2 ON nguva uye 2 OFF nguva pazuva.
- Uchishandisa dhiya repazasi iwe unogona kusarudza maitiro aunoita Kudziya kwako uye Mvura Inopisa, ingave panguva dzakatarwa, inogara iri ON, inogara OFF (imwe neimwe mumasanganiswa akasiyana). Munguva yezhizha kupisa kwepakati kunogona kudzimwa, uchiri kudzora mvura inopisa panguva dzakatarwa.
Kugadzirisa chikwata
Kune mana TAPPETS pane yako yekufona nguva, maviri matsvuku uye maviri ebhuruu:
- matepi matsvuku ndiwo ma ON switch
- matepi eblue ndiwo ma OFF switch
- Bata pakati dema & sirivheri knob neruoko rumwe wofambisa tepi dzvuku yakanyorwa kuti 'A' wachi kuenda panguva yaunoda kuti HEATING/HOT WATER yako ibatike mangwanani.
NB. unogona kuwana matepi akaomarara, saka ungatofanira kuasundidzira zvakasimba kuti uafambise. - Uchiri wakabata knob yepakati, fambisa tepi yeblue yakanyorwa kuti 'B' kusvika panguva yaunoda kuti HEATING/HOT WATER yako ichidzima mangwanani.
- Iwe unogona kuseta ako mamwe mapepi maviri nenzira imwechete yekuseta yako KUSVIRA/KUpisa MVURA yemasikati kana manheru.
EXAMPLE
(NB. Clock iri mumaawa makumi maviri nemana)
Kana uchida kudziya kwako nemvura inopisa KUTI KUTI KUTI KUTI 7am na10am uye ON zvakare pakati pa5pm na11pm, isa matepi sezvinotevera:
- A pa1st ON time = 7
- B pa 1st OFF nguva = 10
- C pa2nd ON nguva = 17
- D pa2nd OFF nguva = 23
Kuisa Wachi
Shandura dhiyairi newachi kusvika nguva chaiyo yaiswa mutsetse nekadoti kakanyorwa TIME
NB. wachi iri mumaawa makumi maviri nemana
RANGARIRA
Iwe unozofanirwa kuseta zvakare nguva mushure mekucheka kwemagetsi uye zvakare kana wachi dzachinja muChirimo uye Autumn
Kushandisa Programmer
Iyo yekusarudza switch inoshandiswa kusarudza kuti iyo 3060 inodzora sei mvura yako inopisa nekudziya. Mvura inopisa uye inopisa inogona kushandiswa pamwe chete mumisanganiswa yakasiyana-siyana, kana mvura inogona kudzorwa pachayo (kureva munguva yezhizha apo mvura inopisa chete inodiwa).
Pane nzvimbo nhanhatu umo chinja chekusarudza chinogona kusetwa.
- H OFF / W OFF
Zvese Kupisa uye Mvura Inopisa zvicharamba ZVAKADZIDZWA kudzamara wachinja marongero. - H KAVIRI / W KAVIRI
Munzvimbo iyi Mvura Inodziya uye Inopisa ichauya uye ichienda zvichienderana nenguva dzawakaronga (ON paA, OFF paB, ON paC, OFF paD). - H Kamwe / W Kamwe
Setting iyi inodarika tappet B neC, saka zvese Kupisa neMvura inopisa zvichabatidza panguva yamaka netappet A uye zvicharamba zviripo kusvika nguva yakanyorwa netappet D. Masevhisi ese ari maviri anozodzima kusvika 'A' zuva rinotevera. - H ON / W ON
Iyi ndiyo 'CONSTANT' chinzvimbo uye mugadziri acharamba akabatidza zvachose kune zvese Kupisa uye Mvura Inopisa, zvisinei nenzvimbo yematepi. - H KAVIRI / W KAMWE
Munzvimbo iyi kupisa kuchauya nekudzima zvichienderana nenguva dzawakaronga (ON at A, OFF at B, ON at C, OFF at D).
Mvura Inopisa ichauya paA uye inogara kusvika D. - H KUBVA / W KAVIRI
Munzvimbo iyi Kupisa kuchange kwakadzimwa zvachose uye Mvura Inopisa ichauya ichidzima zvichienderana nenguva dzawakaronga (ON paA, OFF paB, ON paC, OFF paD).
Cherechedza:
Kana mvura inopisa ichidiwa zuva rose nekudziisa yakavharwa (kureva kupisa, mvura kamwe chete)
- Shandura switch yekusarudza kuenda ku 'H kaviri / W kamwe' uye udzikise thermostat yekamuri kune yakaderera.
- Kana mvura inopisa nguva dzose ichidikanwa nekudziisa (kureva kudzimwa, mvura yakabatidzwa)
- Shandura switch yekusarudza ku 'H on / W on' uye shandura iyo thermostat yekamuri kuti iite yakaderera.
Uchiri nematambudziko?
Fonera mainjiniya enzvimbo yako yekudziya:
- Zita:
- Tel:
Shanyira zvedu websaiti: www.heating.danfoss.co.uk
Tumira email dhipatimendi redu rehunyanzvi: ukheating.technical@danfoss.com
Fonera bazi redu rehunyanzvi 0845 121 7505
(8.45-5.00 Mon-Thurs, 8.45-4.30 Fri)
Kuti uwane vhezheni yakakura yemirairo iyi ndapota bata Dhipatimendi reMasevhisi eKushambadzira panhamba dzinoti 0845 121 7400.
- Danfoss Ltd
- Ampthill Road Bedford
- MK42 9ER
- Tel: 01234 364621
- Fax: 01234 219705
FAQ
- Mubvunzo: Ndinogona here kuisa chigadzirwa ichi pachangu?
- A: Ichi chigadzirwa chinofanirwa kuiswa chete neane electrician anonyatso kwanisa kana ane hunyanzvi hwekudziisa semazano ekuchengetedza.
- Q: Ingani nguva dze ON uye OFF dzinogona kusetwa pazuva?
- A: Iyo programmer inobvumira kuseta 2 ON nguva uye 2 OFF nguva pazuva kune ese ari maviri mvura inopisa nekudziya.
- Mubvunzo: Chii chandinofanira kuita kana matepi akaoma?
- A: Kana ukaona matepi akaomarara, sundidzira zvakasimba kuti uagadzirise kuti aenderane nezvinodiwa.
Zvinyorwa / Zvishandiso
 |
Danfoss 3060 Electro Mechanical Programmer [pdf] Installation Guide 3060 Electro Mechanical Programmer, 3060, Electro Mechanical Programmer, Mechanical Programmer, Programmer |
