Cosmic Byte ECLIPSE TRI Mode Controller User Manual

Cosmic Byte ECLIPSE TRI Mode Controller

Zvigadzirwa Zvinotsanangurwa

Cherechedza: All specifications are for reference and may vary depending on usage and environment.

Package Zviri mukati

• Eclipse Controller × 1
• Replaceable D-Pad × 1
• Mugamuchiri we2.4G × 1
• USB Type-C Cable (1.5m) × 1
• Mushandisi Chinyorwa × 1

ZVAKAITIKA

Mode Switching Position: From left to right: Bluetooth – 2.4G – NS (Xinput Bluetooth, 2.4G Receiver, Switch)

Operation Mirayiridzo

HOME CB Indicator Light

• Blue – iOS and Android
• Orange – 2.4G Mode

Kubatana Kwenguva Yekutanga

• 2.4G Wireless Mode
  • Set the mode switch toggle to 2.4G (Middle).
  • Batanidza USB inogamuchira mumudziyo wako.
  • While the controller is powered off, press and hold the Pairing button for 3 seconds.
  • The logo indicator will flash rapidly. Once it turns solid and the controller vibrates briefly, the connection is successful.
• Makaralı Mode
  • Set the mode switch toggle to Bluetooth (Left).
  • While powered off, press and hold the Pairing button for 3 seconds.
  • The logo indicator will flash rapidly.
  • On your device (PC/Android/iOS), enable Bluetooth and select ‘Xbox Wireless Controller’.
  • When the logo light turns solid and the controller vibrates, the pairing is complete.
• Wired Mode
  • Connect the controller to your device using the included USB Type-C cable.
  • Wired mode activates automatically when connected.

Reconnection
To reconnect to the last paired device (with the same mode), short-press the Home button.

Joystick Adjustment

• Dead Zone Toggle:
  • Press and hold Left and Right Stick (LS/RS) for 5 seconds to switch between 5% and 0% deadzone.
  • Controller will vibrate to confirm the change.
• Active Zone Shape Toggle:
  • Press and hold M + LS or RS for 5 seconds to toggle between 10% square zone and 0% circle zone.

 Turbo and Continuous Fire

• Manual Turbo
  • Press M + A while holding the A button to enable manual turbo (continuous fire).
  • Logo light will flash red rapidly.
• Auto Turbo
  • Press M + A again to switch to auto turbo. Press again to cancel turbo.
  • A single press of A will now fire continuously.
• Clean all Turbo
  • Press M button twice and hold M for 5 secs, controller will vibrate & clean all Turbo settings.
• Turbo Speed ​​​​Adjustment
  • Hold M + Right Stick Up/Down to increase or decrease turbo speed.
  • Vibration feedback indicates change.

ABXY Lighting Adjustment

• Press M + Right Stick Left and Right to adjust brightness.
• 4 Brightness Levels: 0% → 30% → 70% → 100%

Vibration Intensity Adjustment

• Press and hold M + Right Stick Up to increase vibration intensity.
• Press and hold M + Right Stick Down to decrease.
• 4 Levels: 0% (off) → 30% → 70% → 100%

ABXY Layout Shandura

Use the layout switch on the front to toggle between XBOX-style and Alternate-style layouts.

Rapid Trigger Adjustment
Adjust LT/RT trigger travel distance using the trigger mode switch on the back for quick/short press functionality.

Calibration

• Stick & Trigger Calibration
  • Simba pane controller.
  • Bata View + M + Menu for 3 seconds to enter calibration.
  • LED1 and LED3 will flash.
  • Rotate both sticks clockwise 3 full turns.
  • Fully press both triggers 3 times.
  • Switch triggers to short travel mode, then press them fully 3 more times.
  • Press View kubuda.
  • LED1 and LED3 will stay solid for 5 seconds before powering off.
• Gyroscope Kuchengetedza
  • Power off the controller and place it on a flat surface.
  • Bata View + A + B + Home to enter gyro calibration.
  • LED1 and LED2 will flash.
  • After 1 second, press Menu to complete calibration. LEDs will turn off.
  • Calibration must be performed in XBOX (ABXY) layout mode.

Macro Programming (M1/M2 Buttons)

• While connected, hold M + M1 or M2 for 3 seconds to enter programming mode.
• Press the desired button to assign (e.g., A, B, etc.).
• Press M1 or M2 again to save and exit.

Cherechedza: If no button is selected, M1/M2 will be blank. Up to 21 Programmable buttons: A/B/X/Y/D-pad/LB/RB/LT/RT/L3/R3/Menu/View/Joysticks

Power Off

• Hold the Home button for 5 seconds to power off.
• Auto power-off after 10 minutes of inactivity.

Controller Reset
Use a small pin to press the Reset hole to restore factory settings.

 Joystick Force Adjustment (Roller-Based)
The Cosmic Byte Eclipse controller features adjustable joystick tension using a built-in roller mechanism. Follow the steps below to customize the joystick force according to your preference:

• Locate the joystick roller at the base of each analog stick.
• To increase joystick resistance, rotate the roller clockwise.
• To decrease joystick resistance, rotate the roller counter-clockwise.
• Make adjustments gradually and test after each rotation to find your preferred setting.

Cherechedza: The roller mechanism allows for fine-tuning of joystick stiffness for better precision or quicker flick response in different game types (e.g., FPS vs Racing).

Gwaro reChiratidzo cheBhatiri

• Bhatiri rakaderera: Logo light flashes red once every 10 minutes
• Kuchaja: Logo light breathes green
• Zvakakwana: Logo light turns off

Mobile App Download

Download and install the “Key Linker” App from the Google Play Store or Apple App Store for advanced customization and controller adjustments.

Warranty

• The Eclipse Tri-Mode Controller carries a 1-year warranty against manufacturing defects only.
• Physical, water damage, and tampzvigadzirwa zvakagadzirwa hazvina kuvharwa pasi pewarandi.

Scan the QR Code to know the Warranty Claim Procedure.

Tsigira Details

• Customer Care Number: +91 7351615161 (Mon-Sat 10am to 6pm)
• WhatsApp Support: +91 7351615161
• Email: cc@thecosmicbyte.com