Nhanganyaya
The JBL Studio 550P is a 10-inch powered subwoofer designed to enhance your audio experience by delivering powerful and detailed low-frequency sound. This manual provides essential information for the proper setup, operation, and maintenance of your subwoofer, ensuring optimal performance and longevity.
Rutivi rwemberi view of the JBL Studio 550P 10-Inch Powered Subwoofer, showcasing its black finish and sleek design.
Key Features
- 10-Inch PolyPlas Woofer: Features an ultra-ridged PolyPlas cone and cast frame for deep bass impact and excitement without distortion.
- Powerful 300W RMS Amplifier: Yakavakwa-mukati amplifier delivers 300 watts RMS (500 watts peak) for robust and clear low-frequency reproduction.
- Seled Enclosure: Provides tight, accurate bass response.
- Forward-Firing Transducer: Maximizes bass impact and performance.
- Zvakasiyana-siyana: Equipped with LFE and Line-level (RCA) inputs for flexible connectivity with various receivers and processors.
- Adjustable Crossover Frequency: Allows optimization of subwoofer performance to seamlessly integrate with main speakers.
- Chikamu Chekudzora: Increases installation flexibility and helps achieve optimal sound alignment.
- Metal Floor Spikes: Improves bass impact and reduces unwanted resonance.
- Auto Turn-On and Turn-Off: For convenient use and energy conservation.
Gadzirira
Proper placement and connection are crucial for achieving the best sound quality from your JBL Studio 550P subwoofer. Follow these steps for initial setup:
- Kuiswa: Position the subwoofer in your listening area. Experiment with different locations to find the spot that provides the most balanced and impactful bass. Corner placement often enhances bass output.
- Power Connection: Connect the supplied power cord to the subwoofer's power input and then to a suitable electrical outlet (120V, 60Hz for US models; 220V-230V, 50Hz/60Hz for EU models).
- Audio Kubatanidza:
- LFE Input (Recommended for Home Theater): Connect an RCA cable from your receiver's LFE or Subwoofer Output to the LFE Input on the subwoofer.
- Line-Level Inputs (Stereo Receivers/Preamps): Connect RCA cables from your receiver's stereo pre-out (Left and Right) to the Line-Level Inputs (Left and Right) on the subwoofer.
- Kutanga Kubatidza Turn on the subwoofer using the power switch. The auto turn-on feature will activate the subwoofer when an audio signal is detected.
- Speaker Integration: If your receiver has a built-in crossover, set the subwoofer's crossover frequency control to its highest setting (LFE mode). If your receiver does not have a subwoofer crossover, adjust the subwoofer's crossover control to blend seamlessly with your main speakers (typically between 80Hz and 100Hz).
- Phase Adjustment: Use the phase control (0° or 180°) to ensure the subwoofer's output is in phase with your main speakers. Listen for the most impactful and coherent bass.
- Kugadziridza Vhoriyamu: Start with the subwoofer's volume control at a low setting and gradually increase it until the bass output blends well with your main speakers without overpowering them.
Operating Instruction
Once set up, operating your JBL Studio 550P is straightforward:
- Batidza/Kudzima: The subwoofer features an auto turn-on/off function. It will automatically power on when an audio signal is detected and enter standby mode after a period of inactivity. You can also manually turn it on or off using the power switch on the rear panel.
- Kudzora inzwi: Adjust the volume knob on the rear panel to control the subwoofer's output level. Fine-tune this to achieve a balanced sound with your main speakers.
- Crossover Frequency: The crossover frequency knob allows you to set the upper frequency limit for the subwoofer. Frequencies above this setting will be sent to your main speakers. Adjust this to ensure a smooth transition between the subwoofer and your main speakers.
- Phase Switch: The phase switch (0°/180°) helps align the subwoofer's sound waves with those of your main speakers. If the bass sounds weak or hollow, try flipping the phase switch.
Maintenance
To maintain the performance and appearance of your JBL Studio 550P subwoofer, follow these simple maintenance guidelines:
- Kuchenesa: Use a soft, dry cloth to clean the cabinet. Avoid using abrasive cleaners, waxes, or solvents, as these can damage the finish.
- Grille Care: The speaker grille can be gently removed for cleaning. Use a soft brush or vacuum cleaner with a brush attachment to remove dust.
- Kuiswa: Ensure the subwoofer is placed on a stable, level surface. Avoid placing it in direct sunlight, near heat sources, or in areas with excessive moisture.
- Kufefetedza Ensure adequate ventilation around the subwoofer to prevent overheating. Do not block any vents.
Kugadzirisa matambudziko
If you experience issues with your JBL Studio 550P subwoofer, consult the following troubleshooting guide:
- Hapana Simba:
- Check if the power cord is securely connected to both the subwoofer and the electrical outlet.
- Tarisa kuti magetsi emagetsi anoshanda.
- Ensure the power switch on the subwoofer's rear panel is in the 'ON' position.
- Hapana Inzwi:
- Confirm that the audio input cables (RCA or LFE) are securely connected to both the subwoofer and your audio source (receiver/preamp).
- Check the volume level on the subwoofer and your audio source.
- Ensure the subwoofer is powered on (check the power indicator light).
- If using LFE input, ensure your receiver's subwoofer output is enabled and configured correctly.
- Distorted or Unclear Bass:
- Deredza huwandu hwenzwi re subwoofer.
- Adjust the crossover frequency to ensure it blends smoothly with your main speakers.
- Experiment with the phase switch (0°/180°) to find the setting that provides the clearest and most impactful bass.
- Tarisa uone kana tambo dzisina kusimba kana tambo dzakakuvadzwa.
- Ensure the subwoofer is not placed too close to walls or corners, which can cause excessive booming.
Zvinotsanangurwa
| Feature | Tsanangudzo |
|---|---|
| Yakadzika-Frequency Transducer | 10" (250mm) PolyPlas™ cone, cast frame |
| Amplifier Simba | 300 watts RMS; 500 watts peak |
| Frequency Response | 27Hz - 150kHz (-3dB) |
| Crossover Kakawanda | 50Hz – 150Hz (variable), 24dB/octave |
| Enclosure Type | Yakasimbiswa |
| Power Requirement (US) | 120V, 60Hz |
| Power Requirement (EU) | 220V - 230V, 50Hz / 60Hz |
| Kushandiswa kweSimba (Yakamira) | <6W (120V), <0.55W (230V) |
| Kushandisa Simba (Kunyanya) | 360W / 3.8A (120V), 395W / 2.1A (230V) |
| Zviyero (H x W x D) | 17-1/2" x 14-29/32" x 14-31/32" (444mm x 379mm x 380mm) |
| Kurema | Zvamunoda50 lb (23kg) |
| Mounting Type | Floor Yakamira |
| Material | Wood |
| Mutauri Rudzi | Subwoofer |
| Special Feature | Bass Inowedzera |
| Inowirirana Devices | Smartphone, Tablet, MP3 Player, Desktop, Terevhizheni, Projector, Laptop |
| Subwoofer Dhayamita | 10 inches |
| Kutenderedza Inzwi Channel Configuration | 5.1 |
| Color | Nhema |
| Impedance | 8 Ohms |
| Kubatana Technology | RCA |
| Audio Output Mode | Surround |
| Chiyamuro Voltage | 120 Volts |
Warranty uye Support
The JBL Studio 550P 10-Inch Powered Subwoofer comes with a Yakakwana Warranty. For detailed information regarding warranty coverage, terms, and conditions, please refer to the warranty card included with your product or visit the official JBL website. For technical support, service, or any inquiries not covered in this manual, please contact JBL customer support through their official channels.
