SmokerCraft NMEA 2000 Multi Function Display Installation Guide

SmokerCraft-LOGO

SmokerCraft NMEA 2000 Multi Function Display

SmokerCraft-NMEA-2000-Multi-Function-Display-PRODUCT

Loading PDF…
Download PDF

PRODUCT INFORMATION

Thank You!
Thank you for choosing Humminbird®, the #1 name in Fishfinders. Humminbird®
has built its reputation by designing and manufacturing top-quality, thoroughly
reliable marine equipment. Your Humminbird® accessory is designed for
trouble-free use in even the harshest marine environment. In the unlikely event
that your Humminbird® accessory does require repairs, we offer an exclusive
Service Policy – free of charge during the first year after purchase, and available
at a reasonable rate after the one-year period. For complete details, see the
separate warranty card included with your accessory.We encourage you to read
this operations manual carefully in order to get full benefit from all the features
and applications of your Humminbird® product.
Contact our Customer Resource Center at 1-800-633-1468 or visit our
Web site at humminbird.com.
WARNING! This device should not be used as a navigational aid to prevent collision,
grounding, boat damage, or personal injury. When the boat is moving, water depth may
change too quickly to allow time for you to react. Always operate the boat at very slow
speeds if you suspect shallow water or submerged objects.
WARNING! The electronic chart in your Humminbird® unit is an aid to navigation designed
to facilitate the use of authorized government charts, not to replace them. Only official
government charts and notices to mariners contain all of the current information needed for
the safety of navigation, and the captain is responsible for their prudent use.
WARNING! Disassembly and repair of this electronic unit should only be performed by
authorized service personnel. Any modification of the serial number or attempt to repair the
original equipment or accessories by unauthorized individuals will void the warranty.
WARNING! This product contains chemicals known to the State of California to cause
cancer and/or reproductive harm.
NOTE: Some features discussed in this manual require a separate purchase, and some
features are only available on international models. Every effort has been made to clearly
identify those features. Please read the manual carefully in order to understand the full
capabilities of your model.
NOTE: To determine which Humminbird® models are compatible with the NMEA 2000®
network, contact our Customer Resource at 1-800-633-1468 or visit our Web site at
humminbird.com.
NOTE: Humminbird® recommends that the NMEA 2000® network be installed by a certified
NMEA 2000® technician.
NOTE: Product specifications and features are subject to change without notice.
Environmental Compliance Statement: It is the intention of Johnson OutdoorsMarine Electronics,
Inc. to be a responsible corporate citizen, operating in compliance with known and applicable
environmental regulations, and a good neighbor in the communities where we make or sell our
products.
WEEE Directive: EU Directive 2002/96/EC “Waste of Electrical and Electronic Equipment Directive
(WEEE)” impacts most distributors, sellers, and manufacturers of consumer electronics in the
European Union. The WEEE Directive requires the producer of consumer electronics to take
responsibility for the management of waste from their products to achieve environmentally
responsible disposal during the product life cycle.
WEEE compliance may not be required in your location for electrical & electronic equipment (EEE),
nor may it be required for EEE designed and intended as fixed or temporary installation in
transportation vehicles such as automobiles, aircraft, and boats. In some European Union member
states, these vehicles are considered outside of the scope of the Directive, and EEE for those
applications can be considered excluded from the WEEE Directive requirement.
This symbol (WEEE wheelie bin) on product indicates the product must not be disposed of
with other household refuse. It must be disposed of and collected for recycling and recovery
of waste EEE. Johnson Outdoors Marine Electronics, Inc. will mark all EEE products in
accordance with the WEEE Directive. It is our goal to comply in the collection, treatment,
recovery, and environmentally sound disposal of those products; however, these requirements do
vary within European Union member states. For more information about where you should dispose
of your waste equipment for recycling and recovery and/or your European Union member state
requirements, please contact your dealer or distributor from which your product was purchased.
ROHS STATEMENT: Product designed and intended as a fixed installation or part of a system in a
vessel may be considered beyond the scope of Directive 2002/95/EC of the European Parliament and
of the Council of 27 January 2003 on the restriction of the use of certain hazardous substances in
electrical and electronic equipment.
NOTE: The NMEA accessory is compatible with many Humminbird® models, and every
effort has been made to note the differences between the models and functions
throughout this manual. The illustrations in this manual may look different than your
display, but your model will operate in a similar way.
700 Series™, 800 Series™, 900 Series™, 1100 Series™, Humminbird®, InterLink™, and X-Press™Menu are
trademarked by or registered trademarks of Johnson Outdoors Marine Electronics, Inc.
Baekmuk Batang, Baekmuk Dotum, Baekmuk Gulim, and Baekmuk Headline are registered trademarks
owned by Kim Jeong-Hwan.
NMEA 2000® is a registered trademark of the NationalMarine Electronics Association.
Portions of this software are copyright©2012 The FreeType Project (www.freetype.org). All rights reserved.
©2012 Johnson Outdoors Marine Electronics, Inc. All rights reserved.

Introduction

This manual will guide you through the following installation and network
setup instructions for the NMEA 2000® Module:
• Installing the NMEA 2000® Module
• Connecting the Cables
• Powering On
• Configuring the Humminbird® NMEA 2000® Network
• Setting Alarms
• Accessing Views
Introduction

Installation Preparation
Following are instructions for the installation of this accessory. Before you start
installation, we encourage you to read these instructions carefully in order to
get the full benefit from your Humminbird® accessory.
It is important to note that the NMEA 2000® Module installation and
network setup have the following requirements:
Update Software
Confirm all Humminbird®
products are properly
installed and connected.
Confirm the NMEA
2000® network is
properly installed and
connected to power.
Purchase Connection
Accessories
NMEA 2000® Module
Installation
Configurations
Supplies
Your model may require a software update to connect to the NMEA
2000® network. To download the latest software update, log on to
your account at humminbird.com. For assistance, call our
Customer Resource Center at 1-800-633-1468.
Confirm all NMEA 2000® devices (NMEA 2000® Backbone,
T-connectors, Drop Cable, etc.) are properly installed and connected
to power.
See the NMEA (National Marine Electronics Association) Web site
at nmea.org for information about manufacturers of NMEA 2000®
certified products and proper NMEA 2000® network installation.
Depending on your Humminbird® model and network configuration,
you may need to purchase additional accessories to connect your
NMEA 2000® Module to your NMEA 2000® network. See Cable
Connection for more information.
• AS EC [length]E Ethernet Cables (available in a variety of lengths)
• AS EC QDE Ethernet Adapter Cable
• AS ETH 5PS Ethernet Switch
NOTE: To purchase Ethernet Accessory Cables, extension cables, or the
Ethernet Switch, visit our Web site at humminbird.com or call our
Customer Resource Center at 1-800-633-1468 for details.
Only one Humminbird® NMEA 2000® Module can be connected to
a NMEA 2000® network. Review the supported and unsupported
configuration examples in the Specifications section of this
manual for more information.
In addition to the hardware supplied with your installation kit, you
will need a powered hand drill, a 9/64” drill bit, a Phillips
screwdriver, a level, and a pencil.

Installation

The NMEA 2000® Module is designed to mount on any flat, level surface on
your boat. Use the instructions in this section to install the NMEA 2000®
Module on your boat.
1. Determine the Mounting Location
Prior to installation, you must first determine where to mount the NMEA 2000®
Module.
1. Use a level to locate a suitable, flat area to mount the NMEA 2000®
Module.
2. See the configuration examples under Cable Connection. Test run the
cables to the NMEA 2000® Module based on the configuration you will
use. Determine whether you will need to purchase additional Ethernet
Connect Cables or extension cables.
2. Install the NMEA 2000® Module
Once you have determined the mounting location, perform the following
procedures to install the NMEA 2000® Module on your boat.
1. Set the NMEA 2000® Module in place on the mounting surface. Mark
the two mounting screw locations with a pencil.
2. Set the NMEA 2000® Module aside, and drill the two mounting holes
using a 9/64” drill bit.
NOTE: On fiberglass hulls, it is best to use progressively larger drill bits to reduce the
chance of chipping or flaking the outer coating.
NOTE: If themounting surface is thin ormade of lightweightmaterial, youmay need
to add reinforcing material below the mounting surface in order to support the
NMEA 2000® Module.
3. Place the NMEA 2000® Module on the mounting surface and align the
screw holes with the drilled mounting holes. Insert the two #8 screws
(included) through the screw holes and into the drilled mounting
holes. Hand-tighten using a Phillips screwdriver. Hand-tighten only!
NOTE: Apply marine-grade silicone caulk or sealant (separate purchase required) to
both screws and drilled holes as needed to protect your boat from water damage.SmokerCraft-NMEA-2000-Multi-Function-Display-FIG (1)
Cable Connection
Use the instructions in this section to install the cables that connect the NMEA
2000® Module to your NMEA 2000® network.
NOTE: The NMEA 2000® Module does not provide power for the NMEA 2000® network.
1. Determine the System Requirements
Before connecting your NMEA 2000® Module to the NMEA 2000® network, you
must first determine the correct cable requirements for your Humminbird®
model(s).
See the cable connection information for your network configuration as
follows:
• To connect the NMEA 2000® Module to one control head, see
Single Control Head Configuration.
• To connect the NMEA 2000® Module to multiple control heads,
see Multiple Control Head Configuration.
NOTE: You may need to consult your control head installation guide for details.
2. Connect the Cables
Once you have determined your cable requirements, proceed to the section for
that configuration.
NOTE: Confirm all control heads are powered off before proceeding with the installation.
NOTE: The connectors are keyed to prevent incorrect installation, so be careful not
to force the connectors.
Single Control Head Configuration
Use the instructions in this section to connect the NMEA 2000® Module to one
control head. Proceed to the section that matches your Humminbird® model.SmokerCraft-NMEA-2000-Multi-Function-Display-FIG (2)
1a. Connect to a 700 Series™ HD Control Head
To connect the NMEA 2000® Module to a 700 Series™ HD control head, you
will need to use an AS EC QDE Ethernet Adapter Cable.
1. Insert the AS EC QDE Ethernet cable connector into the Ethernet slot
on the 700 Series™ HD Quick Disconnect Mount Cable Collector.
NOTE: The 700 Series™HD control head uses a cable collector for the Quick Disconnect
Mount and the In-Dash Mount. See your control head installation guide for details.
Multiple Control Head Configuration
To connect the NMEA 2000® Module to more than one control head, you will
need to install a Humminbird® Ethernet Switch. The control heads and the
NMEA 2000® Module plug into the Ethernet Switch.
NOTE: Up to four Humminbird® control heads can be connected to the NMEA 2000®
Network via Ethernet Switch at one time.
Multiple Control Head Installation Overview
Before proceeding with this installation, review your Ethernet Switch
installation guide to understand how to install the Ethernet Switch and
connect power.
To install the NMEA 2000® Module using the Humminbird® Ethernet Switch,
you must perform the following procedures:
• Connect the control head(s) to the Ethernet Switch. See the section
that matches your Humminbird® control head model.
• Connect the NMEA 2000® Module to the Ethernet Switch.
• Connect the NMEA 2000® Module to the NMEA 2000® Network.
• Connect the Ethernet Switch power cable to a power source.

1a. Connect a 700 Series™ HD Control Head
to the Ethernet Switch
To connect a 700 Series™ HD control head to the Ethernet Switch, you will
need to use an AS EC QDE Ethernet Adapter Cable.
1. Insert the AS EC QDE Ethernet cable connector into the Ethernet slot
on the 700 Series™ Quick Disconnect Mount Cable Collector.
NOTE: The 700 Series™ control head uses a cable collector for the Quick Disconnect
Mount and the In-Dash Mount. See your control head installation guide for details.
2. Unscrew an Ethernet port cover from the Ethernet Switch.
3. Plug the AS EC QDE Ethernet cable connector into the port. Handtighten
the screw nut to secure the connection.
1b. Connect an 800/900/1100 Series™ Control Head
to the Ethernet Switch
To connect an 800/900/1100 Series™ control head to the Ethernet Switch, you
will need to use a Humminbird® Ethernet Accessory Cable.
1. Insert the Ethernet cable connector into the Ethernet port on the back
of the control head. Hand-tighten the screw nut to secure the
connection.
2. Unscrew an Ethernet port cover from the Ethernet Switch.
3. Plug the Ethernet cable connector into the port. Hand-tighten the
screw nut to secure the connection.
2. Connect the NMEA 2000® Module to the Ethernet Switch
1. Unscrew an Ethernet port cover from the Ethernet Switch.
2. Plug the NMEA 2000® Module cable connector into the port.SmokerCraft-NMEA-2000-Multi-Function-Display-FIG (3)

Hand-tighten the screw nut to secure the connection.
Powering On
Follow the instructions below to power on your Humminbird® control head(s).
To Power On:
1. Press the POWER/LIGHT key.
2. When the Title screen is displayed, press the MENU key to access the
Start-Up Options Menu.
3. Use the 4-WAY Cursor Control key to select Normal (if there is a
transducer attached to the control head) or Simulator (if there isn’t a
transducer attached to the control head).
• If a functioning transducer is connected, Normal operation will be
selected automatically at power up, and your Fishfinder can be
used on the water.
• If a transducer is not connected and you wait too long to select a
Start-Up Option, the system will default to whichever menu is
already highlighted.
• In Simulator you can learn how to use your control head and save
settings in advance for later use.
NOTE: See your control head operations manual for more information about the
Start-Up Options Menu.
NOTE: If you have an InterLink™ connected to the network, the NMEA 2000® will
disable the InterLink™ because both network systems cannot be used at the same time.
Powering On
Follow the instructions below to power on your Humminbird® control head(s).
To Power On:
1. Press the POWER/LIGHT key.
2. When the Title screen is displayed, press the MENU key to access the
Start-Up Options Menu.
3. Use the 4-WAY Cursor Control key to select Normal (if there is a
transducer attached to the control head) or Simulator (if there isn’t a
transducer attached to the control head).
• If a functioning transducer is connected, Normal operation will be
selected automatically at power up, and your Fishfinder can be
used on the water.
• If a transducer is not connected and you wait too long to select a
Start-Up Option, the system will default to whichever menu is
already highlighted.
• In Simulator you can learn how to use your control head and save
settings in advance for later use.
NOTE: See your control head operations manual for more information about the
Start-Up Options Menu.
NOTE: If you have an InterLink™ connected to the network, the NMEA 2000® will
disable the InterLink™ because both network systems cannot be used at the same time.
NMEA 2000® Data Sources Setup
When the NMEA 2000® Module is first installed and connected on the NMEA
2000® network, the control head(s) will automatically detect all connected
NMEA 2000® sources (engines, tanks, depth sounders, etc.). The available
sources are added to the Accessories menu tab, under NMEA2K Gateway.
NOTE: NMEA 2000® menus and menu options are displayed as NMEA2K.
• Source Setup: Use the NMEA2K Gateway menu to select the sources
that will provide data for the digital readouts in the NMEA 2000® Views.
The changes you make are saved even after the unit is powered off.
NOTE: If there is only one source connected on the NMEA 2000® network, that
source will be automatically selected.
• GPS Source Setup: When you power on the network for the first time,
the control head will automatically choose a connected or internal GPS
receiver to provide data to the control head. To use a GPS receiver that
is installed on the NMEA 2000® network, it must be manually selected
from the Network Source Setup dialog box. See NMEA 2000® GPS
Source Setup for more information.
• Control Head(s): The Sources and GPS Source have to be set up on
each control head on the network.
• Lost Data Source: If the control head cannot detect the selected
NMEA 2000® data source, the digital readout box will go blank in
NMEA 2000® Views.
• NMEA 2000® PGN Messages: The NMEA 2000® PGNs are listed in the
Specifications section of this manual.
1. Select NMEA 2000® Data Sources
1. Main Menu: Press the MENU key twice.
Select the Accessories menu tab.
NOTE: In NMEA2K Views, press the MENU key once
to open the Main Menu (see Views).
2. Select NMEA2K Gateway. Press the RIGHT
Cursor key to open the NMEA2K Sources
menu.
3. Press the DOWN or UP Cursor key to select
a source group.
4. Press the RIGHT Cursor key to open the
submenu for that source.
5. Press the DOWN or UP Cursor key to select a
data source. Press the RIGHT Cursor key or
CHECK/INFO key to select the data source.
NOTE: If your control head does not have a CHECK/INFO key, press the top
VIEW PRESET key .
6. Press the EXIT key to return to the NMEA2K Sources menu.
7. Repeat steps 3 – 6 to select another data source.
8. Repeat steps 1 – 7 for each control head on the network where you
want to view NMEA 2000® data.

Network Menu Tab

When a control head is connected to the
NMEA 2000® Module, the Network menu
tab is added to the Main Menu system.
The Network menu tab includes the following menu options:
• Unit Name: Displays the name of the control head. The default Unit
Name is based on its model number and serial number. To change the
Unit Name, see Customize the Unit Name.
• Network Source Setup: Opens the Network Source Setup dialog box.
The Network Source Setup dialog box displays all sonar, temperature,
and GPS sources detected on the network. The sources may be shared
on the network or operating locally with their connected control head.
NOTE: The Sonar and Temperature Sources in this dialog box are not NMEA 2000®
sources. For NMEA 2000® network purposes, youwill only need to open the Network
Source Setup dialog box to select a NMEA 2000® GPS source. See NMEA 2000®
GPS Source Setup.
NMEA 2000® GPS Source Setup
When you power on the control head for the first time, it will automatically
choose the connected or internal GPS receiver to provide data to the control
head. To use a NMEA 2000® GPS source connected on your NMEA 2000®
network, the source must be manually selected from the Network Source
Setup dialog box.
• Digital Readouts: To provide digital readout data for NMEA2K views,
select a NMEA 2000® GPS Source.
• Humminbird® Views: The NMEA 2000® GPS source will display data in
Sonar Views, Chart Views, Bird’s Eye View, etc. It is the only NMEA
2000® source that can display data outside NMEA2K views.
• Multiple Control Heads: If you have more than one unit connected via
Ethernet Switch, you must select the NMEA 2000® GPS on each control
head.
• Menu System and Views: When you select a NMEA 2000® GPS
source, the menu settings, view rotation, and digital readouts will
automatically update on the control head.
1. Select a NMEA 2000® GPS Source
Use the instructions below to select a NMEA 2000® GPS source for your control
head.
To Select a NMEA 2000® GPS Source:
1. Main Menu: Press the MENU key twice. Select the Network menu
tab.
NOTE: In NMEA2K Views, press the MENU key once to open the Main Menu
(see Views).
2. Select Network Source Setup, and press the RIGHT Cursor key.
3. Press the RIGHT Cursor key until the GPS tab is selected.
4. Scroll: Press the DOWN or UP Cursor keys. The selected source is
highlighted in white.
5. Select: Press the RIGHT Cursor key. The check mark indicates that the
source is being used by the control head.
6. Save: Press the EXIT key twice to close the dialog box. Network
settings are saved even after the unit is powered off.
7. Repeat steps 1 – 6 for each control head on the network.

Data Box View

NMEA2K Data Box View

NMEA2K Data Box View presents a full screen view of digital data boxes. It
automatically displays a default data set, and you can also select a data
readout for each data box. See Select Readouts for NMEA2K Views for more
information.
NOTE: The view must be displayed on the screen in order to change the digital
readouts. The availability of the digital readout information varies by model.SmokerCraft-NMEA-2000-Multi-Function-Display-FIG (4)Engine 1 Temperature
2 Engine 2 Temperature
3 Speed Over Ground (SOG)
NMEA2K Depth 4
Course Over Ground (COG) 5
Heading (Hdg) 6

Troubleshooting

Before contacting the Humminbird® Customer Resource Center, please read
the following section. Taking the time to review these troubleshooting
guidelines may allow you to solve a performance problem yourself, and
therefore avoid sending your unit back for repair.
Fishing System Doesn’t Power Up
If your Fishing System doesn’t power up, use the installation guide that is
included with your Fishing System to confirm specific details, making sure that:
• the power cable is properly connected to the Fishing System control head,
• the power cable is wired correctly, with red to positive battery terminal
and black to negative terminal or ground,
• the fuse is operational,
• the battery voltage of the power connector is at least 10 Volts, and
Correct any known problems, including removing corrosion from the battery
terminals or wiring, or actually replacing the battery if necessary.
Fishing System Defaults to Simulator with a Transducer Attached
A connected and functioning transducer will cause the newly-started Fishing
System to go into Normal operating mode automatically. If, when you power
up the Fishing System, it goes into Simulator mode automatically, even though
a transducer is already connected, this means that the control head is not
detecting the transducer. Perform the following troubleshooting tasks:
• Using the Installation Guide that also comes with your Fishing System,
check to make sure that the transducer cable is securely connected to
the Fishing System. Reconnect if necessary, and power up the Fishing
System again to see if this fixes the problem.
• Replace the non-functioning transducer with a known good transducer
if available and power up the control head again.
• Check the transducer cable. Replace the transducer if the cable is
damaged or corroded.

Documents / Resources

PDF thumbnailNMEA 2000 Multi Function Display
Installation Guide · 80-911-0047-00, 80-911-0031-00, NMEA 2000 Multi Function Display, NMEA 2000, Multi Function Display, Multi Function Display

References

Ask a Question

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.