Smart Watch M99 Watch Operating Tutorial User Manual

Smart Watch M99 Watch Operating Tutorial

Product information

Basic parameters

• Product name: Smartphone watch
• Insertion method: SIM card
• Operating temperature: 0° ~ 45°
• Ingress protection: IP67
• Input rated value: 5V— 1A

Packing List

• Smartwatch ×1
• User guide × 1
• card ejector ×1
• screen protector x1
• Watch strap × 1
• Charging cable × 1

Product Introduction

Please read this manual carefully before using the product.

Menu key/return key

• Tap: open app list/ go back to the previous level.
• Double click: switch menu style.
• Long press: Long press for two seconds to turn on Al long press for five seconds to make an SOS emergency ca II.

Power button

• Long press: power on/off/ reboot.
• Tap: Wake/Sleep/Return to Home Screen.
• Double-click: open the taskbar interface.
• Screen shot: Press the rotation key and the power key at the same time.
• Forced restart: press and hold the power button for more than 10 seconds.

In the event of a crash or freeze, press the power key 15 times continuously and quickly, the watch will force a factory reset.

Power on and charge

Press and hold the power button to power on. Align the charging area of the watch with the front of the charging base, and the charging base will automatically ads until the charging interface appears on the watch interface.

If the battery is too low, the watch will not be able to start, please charge it in time.

Insert SIM card

Please use a standard Nano-SIM card, ensuring that the metal chip side of the SIM card is free from dirt or oxidation. Refer to the illustration the correct orientation when inserting the SIM card, aligning the notch on the SIM card with the notch in the tray, and then push the tray into the watch.

After inserting the SIM card, you need to long press the power key to restart the watch to read the SIM card.

Operation guide

1. Swipe down from the right half of the screen on any interface: open the status bar;
2. Swipe down from the left half of the on any interface: open the notification bar;
3. Swipe from right to left on the watch face interface: enter the menu interface.
4. Swipe from left to right on the watch face interface: Enter the card right-swipe shortcut; swipe from left to right on any interface: to the previous level.
5. Swipe up from the bottom of the watch face interface: Enter the shortcut card.

Application installation and uninstallation

Application installation

1. Find the app market in the watch function menu, download and install it directly for use.
2. You can also find the Google Store in the menu, download the APP through the Google Store.

Application Uninstall

1. Find the settings in the function menu, then find “Apps and Notifications” in the settings, view all apps, and you can uninstall the corresponding software.
2. Long press the APP icon in the menu interface to enter.

Mainly display in the watch status bar.

How Bluetooth connects to mobile phone

1. Step 1: Turn on mobile Bluetooth and watch Bluetooth
2. Step 2: Turn on the watch Bluetooth, turn on the Bluetooth headset mode switch, and open the detection.
3. Step 3: Open the Bluetooth assistant and turn on Bluetooth service.
4. Step 4: Scan the QR code of the app with your mobile phone to download it.
5. Step 5: After downloading the APP on your mobile phone, register and log in. After logging in, scan the QR code on the watch to bind it, then follow the steps to bind it. (Special note: Click “Allow” or “Yes” for all pop-up prompts).
6. Step 6: Check if the binding is successful. Click Mobile App-Management-Find Device.
   • If the watch responds, the binding is successful.
   • If there is response, the binding fails. Please go back to the first step and re-bind.
   • Note: After binding is successful, all apps that need to display notifications on the watch must have their app notification management fully enabled on the mobile device

Watch strap assembly and disassembly

1. Watch strap assembly
2. The short band is flush with the top of the watch, and the long band is flush with the bottom of the watch.
3. Press the quick button to the band interface with the groove, and then push it straight in. When you hear a “click”, it is locked.
4. Pull the band gently to check the firm and confirm that it is not loose.

Watch strap disassembly

1. Find the quick-release button: there is a rectangular button on the inside of the strap where it connects to the watch body. (two symmetrical buttons)
2. Press the button: hold down one of the quick-release buttons and gently pull the strap to separate it.

Instructions for use and operation of the camera:
When the camera is pulled out, the camera direction always faces directly upwards; the camera can be rotated 180°, allowing for both front and rear photography. z

Note

1. After removing the camera, if you need to turn off the camera, you can only push the camera in when the camera direct ion is facing the key/menu key (i.e., directly above} and remains on the same horizontal line. Do not use brute force to push the camera in.
2. The can only rotate 180 degrees, and cannot rotate to the exact opposite side. Do not use brute force to rotate when it cannot be turned.
3. Please contact service immediately if you have any problems.

Pull out the camera, which can be used for photography (the camera is directly above at this time)

 

Quick use instructions and precautions :

Please read the following text carefully, it can assist you to use this product smoothly

Instructions for use of the SIM card :

1. Remove the sim card slot and place the SIM card
2. Position the sim card correctlyYellow c hip facing up. notch up close to the card p osition
3. Complete the above steps lo align the card slot and push it forward.
   To ensure the user’s experience and product integrity, please a lign the card slot and push ii Inward instead of using brute force.
   Insert the SIM card when the device is powered off, and then turn it on

Power button and menu key shortcut usage

1. Long press the power button for 2-3 seconds to turn on;
2. While the device is turned on long press the power button for 2-3 seconds to display the shutdown option, and click to shut down;
3. If you press the power button 13 times within3 seconds, the machine will be forced to restore the factory settings;
4. Click the back key/ menu key to enter the menu interface:
5. Swipe from left to on the screen to return to the previous level;
6. Hold down the power button and the back button at the same time for 3 seconds to take a screenshot Double-click the power button to enter the task manager.

Charging operation instructions:

(Note: Align with the marked thimble position to enter the charging state)

Safety and precautions

1. Please wear the watch about one finger’s width away from the wrist bone, as wearing it too loosely may affect the heart rate blood oxygen data. When measuring heart rate and blood oxygen on the watch, please keep your wrist still during the measurement process.
2. The watch has been tested and exhibits water dust resistance performance in a specific environment. However, the watch is not a professional waterproof device, and it can be used during exercise (where it may come into contact with sweat) in the rain, or when washing hands.
3. The watch is not resistant to corrosive liquids such as seawater, acidic or alkaline solvents, chemical agents, etc.
4. Please use this device within the temperature range of 0°C to 45°C. When the ambient temperature is too high or too, it may cause device malfunction.
5. Please charge the device using the charging cable included with this device. When charging with a power adapter, a power adapter with a output voltage of SV and a rated output current of lA that meets the corresponding safety standards should be used. When charging the device, please keep the power adapter, cable, and device in a dry environment, do not touch the power adapter or charging cable with wet hands, and ensure that the power adapter, charging cable, and device have not exposed to rain or soaked in liquid.
6. The product contains an embedded lithium battery that can not be removed. Please do not attempt to replace the battery yourself, as this may the battery device. Improper battery disposal may cause an explosion.
7. Do not disassemble, strike, crush, or throw the device into a fire to avoid an explosion. If battery is seriously swollen, do not continue to use it.
8. Do not leave the device exposed to high temperatures or near heat-generating equipment for a long time such as sunlight, heaters, microwave ovens, ovens, or water heaters, as battery overheating may cause an explosion.
9. The device and its accessories may small parts, please keep them out of the reach of children.
10. This device is not a medical device, and any data/ information provided by the product should not be used as a basis for diagnosis, treatment, and prevention of diseases.
11. If you do not use this product for a long time, please fully charge it, power, and place it in a cool and dry place, and charge it at least once every 3 months.

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Warranty instructions

The user’s watch is covered by a 3-guarantee for performance faults due to non-human damage within the warranty period. If smartwatch experiences non-human main unit performance faults within 15 days from
the date of purchase and cannot be used normally after multiple adjustments, the user can request a free. The replacement requirements include the user’s main unit having no wear or scratches, and all accessories being intact. The accessory replacement service is only valid for normal use. All human (such as: the user disassembling and assembling by themselves, connecting inappropriate accessories, not using according to the instructions) are not covered by the warranty. The warranty period to be calculated from the date when the end user purchases the product, based on the end user’s purchase receipt and valid warranty certificate. If the above proofs cannot be provided, warranty period will be calculated based on the production date of the product purchased by the user. The production date is determined based on the label of our company. If the last day of validity period is a statutory rest day, the last day of the validity period shall be the first working day after the statutory rest day.

Precautions

1. No warranty for products that cannot work normally due to the use of self-compiled or third-party software.
2. No warranty for-disassembly, repair, or modification of performance upgrades not recognized by the company.
3. No warranty for products that have exceeded the service period or have been altered without authorization
4. Smartwatch accessories have a 2-month warranty, and the main watch has a 1-year warranty (non-human damage).
5. The is water-resistant for normal life, and it is fine to wear it when washing hands and face. Please do not wear it when swimming or bathing. If the watch gets water and cannot be turned on due to wearing it while swimming or bathing, such damage is not covered by the warranty. Please be aware!

Warm prompt: if the watch meets water, please dry it up as soon as possible to prevent it from penetrating into the interior of the watch and damaging the parts. Please keep away from high temperature and avoid exposure to the sun.

Scan QR code Operating tutorial video