Smart-AVI SM-D2H-4S 4 Port DP To HDMI KVM Switch
Technical Specifications
Video
- Format: DisplayPort, HDMI
- Maximum Pixel Clock: 165 MHz
- Input Interface: (4) DisplayPort
- Output Interface: (1) HDMI
- Resolution: 3840 x 2160 @ 30 Hz
- DDC Input Equalization: Automatic
- Input Cable Length: Up to 20 ft.
- Output Cable Length: Up to 20 ft.
USB
- Signal Type: USB 2.0, 1.1, and 1.0 w/ internal hub
- Input Interface: (4) USB Type B
- Output Interface: (2) USB 1.1 Type A for KVM Devices, (2) USB 2.0 Type A Transparent
Audio
- Input: (4) 3.5 mm Stereo Audio
- Output: (1) 3.5 mm Stereo Audio
Power
- Power Requirements: 12V DC, 2A power adapter with center-pin positive polarity
Environment
- Operating Temperature: N/A
- Storage Temperature: N/A
- Humidity: N/A
Control
- Front Panel: Push Buttons with LED indicators
- RS-232: Via Serial @ 115200 bps
- Hot Keys: Via Keyboard
Other
- Emulation: Keyboard, Mouse and Video
What’s in the Box
- Part No.: SM-D2H-4S
- Qty: 1
- Description: 4-Port DP-to-HDMI KVM Switch with Audio and USB 2.0 Support
- 12V DC, 2A power adapter with 1 center-pin positive polarity
- Quick Start Guide
| WHAT’S IN THE BOX | ||
| PART NO. | QTY | DESCRIPTION |
| SM-D2H-4S | 1 | 4-Port DP-to-HDMI KVM Switch with Audio and USB 2.0 Support |
| PS12VDC2A | 1 | 12V DC, 2A power adapter with center-pin positive polarity |
| 1 | Quick Start Guide | |
NOTICE
The information contained in this document is subject to change without notice. SMART-AVI makes no war-ranty of any kind with regard to this material, includ-ing but not limited to, implied warranties of merchant-ability and fitness for particular purpose. SMART-AVI will not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance or use of this materi-al. No part of this document may be photocopied, reproduced, or translated into another language with-out prior written consent from SMART-AVI, Inc.
TECHNICAL SPECIFICATIONS
| VIDEO | |
| Format | DisplayPort, HDMI |
| Maximum Pixel Clock | 165 MHz |
| Input Interface | (4) DisplayPort |
|
Output Interface |
(1) HDMI |
|
Resolution |
3840 x 2160 @ 30 Hz |
| DDC | 5 volts p-p (TTL) |
| Input Equalization | Automatic |
| Input Cable Length | Up to 20 ft. |
| Output Cable Length | Up to 20 ft. |
| USB | |
| Signal Type | USB 2.0, 1.1, and 1.0 w/ internal hub |
| Input Interface | (4) USB Type B |
|
Output Interface |
(2) USB 1.1 Type A for KVM Devices
(2) USB 2.0 Type A Transparent |
| AUDIO | |
| Input | (4) 3.5 mm Stereo Audio |
| Output | (1) 3.5 mm Stereo Audio |
| POWER | |
| Power Requirements | 12V DC, 2A power adapter with center-pin positive polarity |
| ENVIRONMENT | |
| Operating Temp | 32° to 104° F (0° to 40° C) |
| Storage Temp | -4° to 140° F (-20° to 60° C) |
| Humidity | 0-80% RH, non-condensing |
| CONTROL | |
| Front Panel | Push Buttons with LED indicators |
| RS-232 | Via Serial @ 115200 bps |
| Hot Keys | Via Keyboard |
| OTHER | |
| Emulation | Keyboard, Mouse and Video |
HARDWARE INSTALLATION
- Ensure that power is turned off or disconnected from the unit and the computers.
- Use DP cables to connect the DP output ports from each computer to the corresponding DP IN ports of the unit.
- Use a USB cable (Type-A to Type-B) to connect a USB port on each computer to the respective USB ports of the unit.
- Optionally connect a stereo audio cable (3.5mm to 3.5mm) to connect the audio output of the computers to the AUDIO IN ports of the unit.
- Connect monitors to the HDMI OUT console ports of the unit using HDMI cables.
- Connect a USB keyboard and mouse in the two USB console ports.
- Optionally connect stereo speakers to the AUDIO OUT port of the unit.
- Finally, power on the KVM by connecting a 12VDC power supply to the power connector, and then turn on all the computers.
Note: You can connect up to 4 computers to the 4 port KVM.
EDID LEARN
The KVM is designed to learn a connected monitor’s EDID upon power up. In the event of connecting a new monitor to the KVM, a power re-cycle is required.
SYSTEM CONTROL
There are three ways to control the SM-DPN: Keyboard HotKeys, RS-232 Serial Commands, and Front Panel Buttons. The settings for the serial connection are as follows: Baud rate: 115200;
Data Bits: 8; Parity: None; Stop Bits: 1; Flow Control: None.
| Command | HotKey | RS-232 |
| Switch KVM | [CT][CT][#]<CR> | //m[#]<CR> |
| Audio Only | [CT][CT]a[#]<CR> | //a[#]<CR> |
| KM Only | [CT][CT]c[#]<CR> | //c[#]<CR> |
| USB Only | [CT][CT]u[#]<CR> | //u[#]<CR> |
| Learn EDID | [CT][CT]e <CR> | //e <CR> |
| SW Reset | [CT][CT]r | //r <CR> |
| Status Query | N/A | //?? <CR> |
| Current HK Trigger | [Alt][Alt][Alt]
k 0 <CR> |
//hk <CR> |
| Update HK Trigger | [HK][HK] k [1|2|3] <CR> | N/A |
Chart Key
- [CT] = Ctrl
- <CR> = Carriage Return (Enter Key)
- [HK] = Current Hot Key Trigger
- 1 = Ctrl (Default) | 2 = Shift | 3 = Scroll Lock
A full Manual can be downloaded from www.smartavi.com/SM-D2H-4S/
- Toll Free: (800) AVI-2123
- Phone: 702-800-0005 2455 W. Cheyenne Ave, Suite 112 North Las Vegas, NV 89032 smartavi.com
Documents / Resources
 |
Smart-AVI SM-D2H-4S 4 Port DP To HDMI KVM Switch [pdf] User Guide SM-D2H-4S, SM-D2H-4S 4 Port DP To HDMI KVM Switch, 4 Port DP To HDMI KVM Switch, DP To HDMI KVM Switch, HDMI KVM Switch, KVM Switch, Switch |