SmallRig RC 350B COB LED Video Light

Specifications

Light Operating Current	8.4A@48V	Power Consumption	403.2W
Light Power Supply	DC48V	Cooling Mode	Active Cooling
Adapter Power Supply	ACl 00 ~ 240V 50 I 60Hz	CRI	96+
TLCI	97+	App Control Type	BLE
Color Temperature	2700K ~ 6500K(±200K)	Remote Ability	slO0m
Radio Frequency	2.4GHz	Power Supply	AC
Size	11.43 X 5.7 X 5.7in	Weight	7.27 Pound

Photometrics

CCT I INT	Distance Illumination	lm	3m	5m
2700K	Bare Bulb	903 fc	100 fc	37 fc
		9720 lux	1080 lux	400 lux
	Hyper–Reflector	6942 fc	540 fc	183 fc
		74700 lux	5810 lux	1970 lux
3200K	Bare Bulb	1171 fc	130 fc	48 fc
		12600 lux	1400 lux	520 lux
	Hyper-Reflector	9061 fc	708 fc	239 fc
		97500 lux	7620 lux	2570 lux
4800K (MAX lux)	Bare Bulb	1468 fc	164 fc	61 fc
		15800 lux	1770 lux	660 lux
	Hyper-Reflector	11524 fc	907 fc	303 fc
		124000 lux	9760 lux	3260 lux
5600K	Bare Bulb	1366 fc	151 fc	57 fc
		14700 lux	1630 lux	610 lux
	Hyper-Reflector	10688 fc	835 fc	281 fc
		115000 lux	8980 lux	3020 lux
6500K	Bare Bulb	1208 fc	133 fc	50 fc
		13000 lux	1430 lux	540 lux
	Hyper-Reflector	9387 fc	736 fc	248 fc
		101000 lux	7920 lux	2670 lux

This is an average result, the number might be slightly different on each light.

Foreword
Thank you for choosing Small Rig COB LED Video Light.

Warnings

1. Please read this User Manual carefully
2. Keep this User Manual and always include it when passing the product to a third party.
3. Heed all warnings and follow all instructions in this User Manual.
4. Close supervision is necessary when any fixture is used by or near children. Do not leave the fixture unattended while in use.
5. Care must be taken as burns can occur from touching hot surfaces.
6. Do not operate the fixture if a cord is damaged or if the fixture has been dropped or damaged until it has been examined by qualified service personnel.
7. Position any power cables so that they will not be tripped over, pulled or put into contact with hot surfaces.
8. If an extension cord is necessary, a cord with an amperage rating at least equal to that of the fixture should be used. Cords rated for less amperage than the fixture may overheat.
9. Always unplug the lighting fixture from the electrical outlet before cleaning and servicing or when not in use. Never yank the cord to remove the plug from the outlet.
10. Let the lighting fixture cool completely before storing.
11. To reduce the risk of electric shock, do not immerse this fixture in water or any other liquids.
12. To reduce the risk of fire or electric shock, do not disassemble this fixture. Contact smallrig@smallrig.com or take it to qualified service personnel when service or repair work is required.
13. The use of an accessory attachment not recommended by the manufacturer may increase the risk of fire, electric shock, or injury to any person operating the fixture.
14. . Power this fixture by connecting it to a grounded outlet.
15. Please remove the protection cover before powering the light.
16. Please remove the 8/A protection cover before using the reflector.
17. Please do not block the ventilation, and do not look at the light directly when it is powered on.
18. Please do not place the LED lighting fixture near any liquids or other flammable objects.
19. Only use a dry microfiber cloth to clean the product.
20. Please have the product checked by authorised service personnel or agents if your product has a problem.
21. The malfunctions caused by unauthorised disassembly are not covered under the warranty.
22. We recommend only using the original Small Rig cable accessories. Please note that our warranty for this product does not apply to any repairs required due to any malfunctions of unauthorised SmallRig accessories, although you may request such repairs for a fee.
23. This product is certified by CE, Rohs, UKCA, FCC, IC, KC, RCM, TELEC, and PSE. Please operate the product in full compliance with the operation standards. Please note that this warranty does not apply to repairs arising from malfunctions, although you may request such repairs on a chargeable basis.
24. The instructions and information in this manual are based on thorough, controlled company testing procedures. Further notice will not be given if the design or specifications change.

Please do not disassemble the product. If you have any questions, please contact the seller to apply for after-sales service.

FCC Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Warning
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note
This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 7.5 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy. If not installed and used according to the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try reorienting or relocating the receiving antenna.

• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet in a different circuit than the receiver is connected to.
• Consult the dealer or an experienced radio/1v technician for help.

RF Warning Statement
The equipment complies with FCC Radiation exposure limits set forth for uncontrolled enviroment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

In the Box

When you unbox the product, please make sure all the items below are included. Otherwise, contact the seller immediately

Product Details

Installations

Attaching/ Detaching the protection cover
Push the handle of the lever in the direction of the arrow shown in the picture, and rotate the cover to pull it out. Reverse rotation will put the protection cover into place.

Notice: Always remove the protection cover before turning on the light. Always reinstall the cover when packing it away.

Installation and removal of the reflector
Push the lever handle according to the arrow direction shown in the picture and rotate the reflector into it. Rotating in the opposite direction pulls out the reflector.

Notice: The installation of other Bowen’s Mount modifiers is the same.

Setting up the light
Connect and tighten the stand adapter with the light through the Arca-type clamp and mount plate, rotate the tie-down knob to fix the stand adapter on the light stand. Please remember to lock the stand adapter with the locking handle once you’ve adjusted the light to the required angle.

 Soft light umbrella installation
Insert the soft light handle into the hole and lock the knob on the hole.

The Power Supply
Powered by AC

Notice

• Please press the spring-loaded lock button on the power cord to remove the cord.
• Do not pull it out forcibly.

Operations

Press the power button to turn the light on and off.

 Manual control

 Brightness adjustment
Rotate the INT adjusting knob to adjust the brightness with 1 % variable and the brightness change range is 0 ~ 100%, the change of the brightness will be displayed in real time on the light body.

Colour temperature adjustment
Rotate the CCT knob to adjust the color temperature, and the CCT range is 2700K ~ 6500K.

FX and FRO adjusting control.

• Press the FX button to get Normal and Paparazzi/ TV/ Fault Bulb/ Lightning/ Breath Party/ Flash/ Flame/and Firework, nine kinds of FX.
• Rotate the FRO knob then switch to the frequency adjustment, the change range is 1 ~ 10.
  • Notice: The brightness and FRO of every FX can be set separately.

BLE reset

•  Long press the Reset button for 3 seconds, the BLE icon will appear in the upper right if the LCD display. The icon flashes 6 times and the BLE is reset.
• Then you can reconnect the light through the SmallGoGo App on your smart device.

 App control
The user can download the SmallGoGo App and connect the device named 350b-xxxxxx I 450B-xxxxxx.

• After the light is controlled by the App, the BLE icon will be displayed on the upper right of the light LCD.
• Notice: Please enable the mobile location function when using the App.

Please visit www.smallgogo.com for more details regarding how to use the App to control your lights.

OTA mode
Firmware updates can be updated online via the SmallGoGo App for OTA updates.

 Using the SmallGoGo App
You can download the SmallGoGo App from the ios App Store or Google Play Store to enhance the functionality of the light. Please visit www.smallgogo.com for more details regarding how to use the app to control your lights.

• Operation Manual
• App Download

Panel control

• Connect the control panel to the light.
• The operation interface is the same as that on the light.

Notice: The control panel is not the standard configuration and needs to be bought separately.

Documents / Resources

SmallRig RC 350B COB LED Video Light [pdf] User Manual RC 350B, RC 350B COB LED Video Light, COB LED Video Light, LED Video Light, Video Light

References

• User Manual