Keilton Basic RM51 Pule Mamao mo Fa'amau Fa'amau

Fa'amatalaga

The RM51 Remote is used to program the configurations of the Keilton Basic sensors using infrared (IR) communications with the devices. It offers 6 default modes of configurations plus manual settings. Customer configurations can be created, saved, and then sent to each device, ensuring a rapid deployment.

Vaega

• Fa'atauga maualalo le mana.
• Infrared communication.
• Setting most of the Keilton Sensors G2.
• Custom Configurations can be saved to A, B, C, D, or For.
• 40′ maximum IR range.
• RML (included with new orders, available as an accessory for order), installed, will increase the IR range. (See table below)

Fa'amatalaga

Fa'amatalaga Fa'atonu

Fa'ata'ita'iga	Fa'amatalaga
RM51.A0	Basic Sensor Controller RM51
RM51.A1	Basic Sensor Controller RM51 With RML

Fa'amatalaga Fa'atonu - Mea fa'aoga

Fa'ata'ita'iga	Fa'amatalaga
RML	Extended IR range for commissioning

Fua

Fa'ailoga oloa

Fa'atonuga Mamao

Fa'atonuga (Fa'atonu)
To begin commissioning, follow these steps:

1. Filifili se mea e manatua aifile: A, B, C, D, poʻo le E.
2. The remote’s indicator lights will flash, indicating the currently saved settings.
3. Settings can be configured by pressing the appropriate buttons in the highlighted gray area of the remote (TRIM-LEVEL, SENSITIVITY, HOLD TIME, STANDBY DIM, STANDBY TIME, and PHOTOCELL). Review the selected settings and make changes as needed.
4. Point the remote at the desired luminaire and press “SEND.”
5. The luminaire will flash twice to confirm that he settings are saved. Changing a parameter in a memory profile will automatically override previous settings.
6. If configuring multiple luminaires, repeat steps 4 and 5 after selecting the configured memory mode.

E Mode allows for visual adjustment to choose the desired dimming level.

Seleseina o le Ao (Faiga F)
Continuous Adjustment Mode adjusts dimming levels based on daylight.

1. Point the remote at the desired luminaire and press “ON,” then press DIM+ or DIM- to adjust the dimming level.
2. Press “F.” The indicator lights on the remote will show the current saved settings. Note: Only TRIM-LEVEL, SENSITIVITY, and HOLD TIME can be selected for Daylight Harvesting settings
3. Review the selected settings and make changes as necessary. Press “SEND.”
4. If the configuration is successful, the luminaire will flash twice to confirm that the setting is saved. If configuring multiple luminaires, select the configured Daylight Harvesting settings, then follow steps 1, 2, and 3.

Galuega Faaopoopo Mamao

ON	Liliu ON moli.
TOTO	Liliu TOTO moli.
TOFOTOGA	The fixture enters the test mode and exits automatically after 5 minutes. The test mode parameters are configured as follows: Trim-level: 100%, Ma'ale'ale: maualuga, Taimi taofi: 2s, Standby dim: 50%, Taimi tutumau: 2s.
TOE FAI	Trim= 100%, Sensitivity = Maualuga, T1 = 5 minu, Standby Dim = 30%, T2 = 60 minu, Photocell = TOTO.
DIM+/-	Press Dim+ or Dim- to adjust brightness in 0.5V increments. Hold the button for continuous pouliuli
TITIMI-LEVEL	Set the Maximum brightness.
AGAFAI	Set the motion sensitivity of the sensor Maulalo:50% / MAUGA:100%, ESE: disable the motion detection function.
TAIMI TATAU	O le umi e alu e aunoa ma le iloa o tagata nofoia a'o le'i fa'afeiloa'i i le fa'ata'ita'i fa'apouliuli.
STANDBY DIM	Select any standby dim level.
FAATALI MAI TAIMI	Standby time, when the time is set to “∞”, the daylight detection function is activated.
PHOTOCELL	visible light threshold, the fixture is allowed to be turned on when it falls below the threshold Maulalo:5fc / MAUGA:20fc, CAL: Collect the current visible light illuminance as the threshold, ESE: disable PHOTOCELL function.
TULAGA	Default configuration parameters for modes A ia F.
AVE	Auina atu tulaga i le masini.
TALA FA'ATAU A	Trim= 100%, Sensitivity = Maulalo, T1 = 30 minu, Standby Dim = 50%, T2 = ∞, Photocell = CAL.
TULAGA FA'AVAE B	Trim= 100%, Sensitivity = Maulalo, T1 = 30 minu, Standby Dim = 50%, T2 = 15 minu, Photocell = CAL.
TULAGA TULAGA C	Trim= 100%, Sensitivity = Maulalo, T1 = 30 minu, Standby Dim = 50%, T2 = 15 minu, Photocell = TOTO.
FA'ATAU FA'AVAE D	Trim= 50%, Sensitivity = Maulalo, T1 = 30 s, Standby Dim = 50%, T2 = 30 minu, Photocell = CAL.
FA'ATAU FA'ATAU E	Manual Dimmer Mode, Trim 100%.
F	Daylight Harvesting, Trim= 50%, Sensitivity = Maulalo, T1 = 15 minu.

Faafesootai matou

• 7001 Columbia Gateway Drive, Suite 210, Columbia, MD 21046, USA
• T: +1 443-320-2233 (M-F 9 am-5 pm ET)
• E: support@autani.com

FAQ

How do I change the memory profile faatulagaga?

Select the desired memory profile on the remote and adjust settings as needed before pressing SEND to save

Can I configure Daylight Harvesting settings for multiple luminaires simultaneously?

No, you need to configure Daylight Harvesting settings for each luminaire individually using the F Mode on the remote.

What is the expected operation if the user sets Standby Time to something other than INFINITE?

moiton -> the intensity of ambient light is lower than the threshold set by the PC->turn on the light and dim to trim-level->t1 timeout->dim to standby dim ->t2 timeout->turn off the light.

If it does not turn OFF the fixture, why would Mode B and D use CAL as the default?

The ambient light intensity stored by CAL will serve as the threshold for turning on the lights, but it has no connection with the function of turning off the lights.

Pepa / Punaoa

Keilton Basic RM51 Pule Mamao mo Fa'amau Fa'amau [pdf] Tusi Lesona a le Pule RM51.A0, RM51.A1, RM51 Pule mamao mo le faʻapipiʻiina o mea, RM51, faʻamama mamao mo le faʻaogaina o mea faʻapipiʻi, mo le faʻaogaina o mea faʻapipiʻi, masini faʻapipiʻi

Fa'asinomaga

• Tusi Taiala