Argon ONE V3 Case Mo Raspei

ARGON ONE V3 / M.2 NVMe PCIE VAEGA

1. Maneta Aveese
2. Ufiufi pito i luga
3. 40 Pin GPIO Avanoa
4. Pusa fau
5. 3.5mm Audio Port (E na'o Argon e galue
6. USB-C Malosi i totonu
7. 2xTypeAHMI
8. Pule Malosi
9. Gigabit Ethernet 02xUSB3.0
10. 2xUSB2.0
11. ID Pele Film Strip
12. PC le Socket
13. Mana Pogo Pins
14.  THRML M.2H mea'ai 49
15. M.2 NVMe Drive Socket

ARGON ONE V3 FAAALIGA

ARGON ONE V3 ADD ON MODULES

FAATONUGA FAAPOTOPOTOGA

1. Faʻafesoʻotaʻi le Raspberry Pi® 5 i le HDMI-Power Board. Tuu le
   Silicon Thennal Pads ile Argon ONE V3 case heatsinks (CPU ma PMIC).
   Raspberry Pi 5 faʻatasi ma HDMI-POWER BOARD e le mafai ona faʻamalo pe a le fesoʻotaʻi ma le pusa pito i luga.
2.  Filifili le Argon ONE V3 Power Button Mode Management Mode:
   ARGON ONE V3 / M.2 NVMe PCle CASE JUMPER PIN FA'ATAU
   
3. Fa'afeso'ota'i le PCle Pipe Flat Flex Cable i le Raspberry Pi® 5 PCIE uafu.
4. Fa'afeso'ota'i le Argon BLSTR DAC Board i pine o le Argon ONE V3 RP2040-Fan Board.
   Argon BLSTR DAC e manaʻomia e faʻagaoioia ai le 3.5mm Audio Port.
5. Faʻafesoʻotaʻi ma le faaeteete Raspberry Pi9 5 HDMI-Power assembly i le GPIO fafine ma le 6-pln Power port o le Argon ONE V3 case.
6.  Fa'amautu fa'amau fa'aulu fa'amau e fa'amau ai le Raspberry Pi'” 5 ma le HDMI-Power Board fa'apipi'i i le pito i luga.
   
7. Fa'amau le faavaa pito i lalo o le Argon ONE V3 / M.2 NVMe PCle e fa'aaoga ai fa'avili lapotopoto ulu.
8. Fa'afeso'ota'i lau M.2 NVMe Drive i le Argon ONE V3 M.2 NVMe PCIe Expansion Board. O le a talia e lenei Komiti Fa'atonu le M.2 Key M ma le M.2 Key B+M NVMe Storage Drive.
   E LE fetaui lenei Komiti Fa'atonu ma M.2 SATA Storage Drives.
   E mafai ona e fa'anofoina le fa'ailoga fa'ailoga i luga o le laupapa i le lapo'a talafeagai o lau Ta'avale Teuina.
   OMI le POLOSILI ile TURN ON pe a uma ona faʻapipiʻi ma faʻafesoʻotaʻi le Malosiaga

FA'ATAU ARGON ONE V3 POWER BUTTON MA FA'ATA'U PULE ILI

1. STEP 1: Fa'atulaga le EE PROM Seti e fa'amanino ai le mana ma le fa'auma mai le NVMe.
   1. Fesoʻotaʻi ile Initaneti, ia mautinoa ua faʻafouina Raspberry Pi TI me ma faʻatino i le Terminal.
   2. Toe fai.
2. Laasaga 2: Faʻapipiʻi le Argon Control Script ma Config.txt Seti 1. Faʻafesoʻotaʻi i le Initaneti ma faʻatino i le Terminal.
   

Toe fai.
T'ATA'I
Ina ia aveese le Argon ONE V3 script e mafai ona e faia i le kilikiina o le Argon ONE V3 Desktop Icon. E mafai foi ona e aveese le tusitusiga e ala i le Tenninal Shell e ala i le taina:

Toe fa'afou i taimi uma pe'a uma ona suia so'o se fa'atulagaga po'o le fa'a'ese'esega mo fa'atonuga toe fa'aleleia ina ia aoga.

FA'ATA'U AUTOMA I ARGON ONE V3 SCRIPT

O le ARGON ONE Script e otometi le faʻapipiʻiina o faletusi uma, polokalame ma le EEPROM ma le Config faʻatulagaina e manaʻomia mo le RP2040 i le Argon ONE V3 Case ina ia mafai ona fesoʻotaʻi ma le Raspbenry Pl 5 ma faʻatino galuega eseese e pei o Active Cooling ma Power Management.
O loʻo i lalo le FAʻAALIGA na faʻaogaina e le Argon ONE Script.

FA'ATAU LE ARGON ONE V3 PUMA MA FA'ATAU ILI

I luga o le faʻapipiʻiina o le Argon ONE V3 script e ala i le faaletonu, o le faʻatulagaina o le Argon ONE V3 Power button ma le faʻamafanafanaina e faʻapea:

Ae ui i lea, e mafai ona e suia pe faʻapipiʻi le FAN i mea e te manaʻo ai i le kilikiina o le Argon ONE V3 Desktop icon.

Pe ala i le Teminal Shell e ala i le taina ma mulimuli i le faatulagaga faʻapitoa: 

argon-config

FA'ATAU ARGON BLSTR DAC MO RASPBERI Pl OS

1. Ia mautinoa ua e faʻapipiʻi le Argon Configuration Script i totonu o oe e ala i le tamoe i le Terminal Shell:
   
2. Ina ia ulufale i le Argon Configuration Tool ituaiga argon-config i le Terminal Shell. Ulufale numera 3 e faʻapipiʻi Argon BLSTR DAC Configuration.  
3. A maeʻa faʻapipiʻi e mafai ona e vaʻai i lenei mea.
4. 11 e te manaʻo e faʻapipiʻi ma le lima le ARGON BLSTR DAC naʻo le faʻaopoopoina o le seti i le config file maua ile /boot/flnnware/config.txt
   
5. Ona Toe Toe.

Mo nisi fa'amatalaga fa'amolemole asiasi: https://largon40.com/blogs/argon-resources

FAATUATU LE RECEIVER INFRARED
O le lomiga lata mai o lo'o i ai se fa'apipi'iina o le Infrared Receiver e mafai ona fa'apipi'i ON ma OFF le masini e fa'aaoga ai le Argon 40 IR Remote.

Ina ia fetuutuunai le Infrared Receiver ON/OFF faailo o Argon ONE V3 ituaiga i le Terminal Shell:
argonone-ir
Ona mulimuli lea i faatonuga e pei ona faailoa atu.

FAATUATUA IR MAMAITI & LASA
Argon JR mamao  https://ljargon40.com/products/argon-remote
Argon PWR GaN 27W Tiliva Malosiaga  https://ljargon40.com/products/argon-pwr-gan-usb-Pd·POWer-supply-27-watts

ARGON ONE V3 SU'E FA'AVAE FA'ATA'U

1. Fa'afeso'ota'i le Socket USB-C i totonu ile RP2040-Fan Board ile 5V Power Supply.
2. Oomi le Pule ON Button.
   
3. Ole mea lea ole a amata ai ile FAN ile TAGATA ile 5 SECONDS ona taofi lea.
4. E fa'ailoa mai ai e mafai e le RP2040 ona feso'ota'i lelei ma le Power Button ma le FAN i totonu ma o lo'o galue atoatoa le laupapa.

FA'ATAU ARGON ONE V3 FUAFUAGA

1. La'u mai i lau PC po'o le Raspberry Pi Computer le Argon ONE V3 Firmware fou mai le so'oga i lalo: https://download.argon40.com/firmware/ArgonOne.uf2
2. OMI ma TUMAU le Argon ONE V3 POWER BUTTON a'o e fa'afeso'ota'i le Internal USB•C ma le Data cable i lau PC po'o le komepiuta Raspberry Pl.
3. Ole mea lea e tu'u ai le RP2040 ile USB masini fa'apipi'i masini.
   
4. Ona mafai lea ona e TOSO ma TAGAI lau LATEST compiled .uf2 flnnware file i le masini teuina tele USB.
5. Aveese le masini pe a maeʻa.

www.argon40.com 

Pepa / Punaoa

Argon ONE V3 Case Mo Raspei [pdf] Taiala mo Tagata Fa'aoga V3, PI 5, TASI V3 Pusi Mo Raspeli, TASI V3, Pusa Mo Raspeli, Raspeli

Fa'asinomaga

• Tusi Taiala