Sky-Lighting BR30RGBCW10W Connected LED Lamp Instructions

To pair the lamp, press the (+) Add Device button in the app and follow the instructions on the screen. Reset to factory settings by pressing the button for 3-5 seconds. The lamp will blink at 50% intensity before reaching 100% to indicate a connection to the Tuya app. Control the lamp via the app or by pressing the main button briefly.

Completing Installation:

Follow the on-screen instructions to complete the installation. Accept any location authorization requests to enable WiFi access for Android or iOS devices.

FAQ

Q: What should I do if the lamp does not pair with the Tuya app?
- A: Ensure the lamp is in pairing mode and that your phone’s Bluetooth and WiFi are enabled. Try resetting the lamp and retrying the pairing process.
Q: Can I control the lamp without using the Tuya app?
- A: Yes, you can control the lamp by pressing the main button on the device.

Operation

This connected led lamp will allow you to control you rooms lighting from your smart phone or tablet with the Tuya app. Before starting the setup, you’ll need to write down your WiFi network name and password, remember to respect spaces and capital letters.

Warning:

This connected light bulb only works on WiFi network at 2.4GHz.Please check the WiFi settings of your box. –
Do not connect the chain to the supply while it is in the packing. The lamps are not replaceable.

Important information

Before installing or replacing the lamp,please read this manual completely and observe the following precautions:

Please do not install the product if your hands are wet or if you are in a humid environment.

Please do not use a dimmer switch.Use only the dedicated app to dim the brightness.
Suitable for use between -20°C and 40°C.

Do not open or disassemble the product.
Do not use the product if it is out of order, damaged or emits abnormal noises.

Thoroughly clean the surface on which the lamp will be applied.

Installation in 4 steps

Installation of the lamp

Unwind the lamp at your convenience – Plug the all into a power outlet.

Installing the mobile app and creating an account

Once the lamp is installed, please proceed with pairing. if you don’t have the Tuya app, download it from the Android Play Store or the Apple Store. Open the app. If you are a new user, follow the instructions on the screen to create your account.

Pairing the lamp

To register your new lamp, press the (+) “Add Device” button in the upper right corner, and follow the instructions on the screen. To reset the product to factory settings, you must press the button for 3-5 seconds, the lamp will blink at 50% light intensity. Once it has reached 100% light intensity, the product is then connected to the TUYA app. You can control the product via the Tuya app or by briefly pressing the main button.

4-Follow the instructions

To complete the installation please follow the instructions on the screen. If a location authorization request message appears,you will need to accept it to allow Android or iOS devices to retrieve your WiFi.

FCC Statement

FCC Caution:

This device complies with part 15 of the FCC Rules. Operation is subject to the following twoconditions:

This device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with theinstructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment . This equipment should be installed and operated with a minimum distanceof 20cm between the radiator& your body.

Documents / Resources

Sky-Lighting BR30RGBCW10W Connected LED Lamp [pdf] Instructions
2AVJP-BR30RGBCW10W, 2AVJPBR30RGBCW10W, br30rgbcw10w, BR30RGBCW10W Connected LED Lamp, BR30RGBCW10W, Connected LED Lamp, LED Lamp, Lamp

References

User Manual

Sky-Lighting BR30RGBCW10W Connected LED Lamp

Specifications

Product Usage Instructions

FAQ